Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.
Single Ply Endless Lifting Sling
Một lớp, one lapped joint, không có kết thúc. The lightest closed loop in the range: it folds into a pocket, turns a tight radius and drapes over the load — 1 đến 12 tại 7:1 hai MỘT 1492-1.

The word to be careful with is ply. It does not mean two slings or two bands in parallel; it means how many layers of webbing are woven into the one band the loop is made from. Single ply is one layer, and everything that follows — the 4 mm section, the weight per metre, the way it turns round a small radius, and the capacity it can be given at a given width — comes from that one decision.
What one layer actually gives you
Four practical differences separate the single-layer loop from the duplex build, and each one shows up on a different job:
- MỘT 4 mm section. The band folds into a pocket, coils onto a hook and passes between a load and a tight gap where a thicker band will not go.
- Less weight per metre. The ladder below runs from 0.20 kg/m tại 1 đến 2.05 kg/m tại 10 t — a one-handed carry for the sizes most yards actually use.
- More supple over a radius. One layer conforms to pipe, tube and rolled sections instead of standing off them, so contact is over the full width rather than at two edges.
- Một khớp, thin and easy to read. The lapped joint is the only made connection in the load path; in a single layer the stitching rows sit on one visible face, with no second layer masking them.

Single ply against duplex, at the same width
The two builds are not two grades of the same thing; they are two answers to different questions. The comparison below is the one we use in quotation, and the widths are the published single-ply ladder.
| Lớp đơn | song công | |
|---|---|---|
| Layers in the band | Một | Hai, woven as one band |
| Section thickness | 4 mm at the standard ladder | Roughly twice the single-ply section |
| Capacity at a given width | The ladder figure | Higher — the reason duplex exists above the single-ply range |
| Trọng lượng mỗi mét | 0.20 kg/m tại 1 đến 2.05 kg/m tại 10 t | Higher for the same width |
| Xử lý | Folds small, turns a tight radius, drapes onto the load | Cứng hơn; sits flatter over an edge and resists abrasion longer |
| Nó thắng ở đâu | Dưới đây về 6 t, tight gaps, đường kính nhỏ, mixed rigs | High capacity in a narrow width, rough edges, heavy abrasion |
| Chung | One lap, stitching visible on the face | One lap through the doubled band |
The duplex build has its own page: double ply endless lifting sling.
The capacity ladder, lớp đơn
Working load limits are quoted in straight lift, Tại 7:1 hai MỘT 1492-1. Colour follows EN 1492-1 and is a capacity band, not a material; bên trên 10 t there is no colour code and the label is the only rating.
| WLL, nâng thẳng | Màu sắc | Chiều rộng tham chiếu | Phạm vi chiều dài | Xấp xỉ. cân nặng | Nghẹt thở (× 0.8) |
|---|---|---|---|---|---|
| 1 t | màu tím | Xác nhận theo đơn đặt hàng | 0.5 – 100 tôi | 0.22 kg/m | 0.8 t |
| 2 t | Màu xanh lá | 50 mm | 1 – 100 tôi | 0.35 kg/m | 1.6 t |
| 3 t | Màu vàng | 75 mm | 1 – 100 tôi | 0.52 kg/m | 2.4 t |
| 4 t | Xám | 100 mm | 1.5 – 100 tôi | 0.80 kg/m | 3.2 t |
| 5 t | Màu đỏ | 125 mm | 1.5 – 100 tôi | 0.85 kg/m | 4.0 t |
| 6 t | Màu nâu | 150 mm | 1.5 – 100 tôi | 0.96 kg/m | 4.8 t |
| 8 t | Màu xanh da trời | 200 mm | 2 – 100 tôi | 1.34 kg/m | 6.4 t |
| 10 t | Quả cam | 250 mm | 2 – 100 tôi | 1.64 kg/m | 8.0 t |
| Bên trên 10 t | Không có mã màu | Duplex build | Để đặt hàng | Theo yêu cầu | Nhãn chi phối |
Widths and weights are the published series for this range; the finished width, ply and weight are confirmed on the order acknowledgement.
Chiều rộng, safety factor and the same capacity
A higher safety factor needs a wider band for the same working load limit, đó là lý do tại sao cột chiều rộng có ba giá trị. Tell us the standard your site works to and the sling is built to it; the figures below are the single-ply polyester ladder.
| WLL | Tại 5:1 | Tại 6:1 | Tại 7:1 | độ dày | Trọng lượng tại 7:1 |
|---|---|---|---|---|---|
| 1 t (1 000 kg) | 25 mm | 25 mm | 30 mm | 4 mm | 0.20 kg/m |
| 2 t (2 000 kg) | 50 mm | 50 mm | 60 mm | 4 mm | 0.60 kg/m |
| 3 t (3 000 kg) | 75 mm | 75 mm | 90 mm | 4 mm | 0.78 kg/m |
| 4 t (4 000 kg) | 100 mm | 100 mm | 120 mm | 4 mm | 0.90 kg/m |
| 5 t (5 000 kg) | 125 mm | 125 mm | 150 mm | 4 mm | 1.14 kg/m |
| 6 t (6 000 kg) | 150 mm | 150 mm | 180 mm | 4 mm | 1.33 kg/m |
| 8 t (8 000 kg) | 200 mm | 200 mm | 240 mm | 4 mm | 1.85 kg/m |
| 10 t (10 000 kg) | 250 mm | 250 mm | 300 mm | 4 mm | 2.05 kg/m |
| 12 t (12 000 kg) | 300 mm | 300 mm | 300 mm | 4 mm | 2.70 kg/m |

khớp, and why it is the first thing to look at
Một chiếc địu vô tận được sử dụng vô tận, không liền mạch. Dải được quấn lên chính nó và đóng lại bằng các hàng khâu song song dày đặc; vạt áo đó là một khớp có đủ độ bền và nó nằm trong đường tải. Đó là sự kết nối duy nhất được tạo ra trong toàn bộ bài viết.
On a single-layer loop that joint is easier to inspect than on a duplex one, because the stitching rows lie on one visible face rather than between two layers. Look for broken or pulled stitches, a lap that has started to open, and abrasion where the lap passes over an edge. If the joint is sound, the rest of the loop is one continuous band and can be read anywhere along its length.

Three hitches from the same loop
The marked figure is the straight-lift rating; every other arrangement is derived from it. Kích thước dây đeo cho phù hợp với móc mà đội sẽ thực sự lắp đặt, không đến cái trong kế hoạch thang máy.
| Xô | Yếu tố chế độ | Ý nghĩa của nó trên trang web |
|---|---|---|
| Thẳng đứng | × 1.0 | Hình nhãn áp dụng trực tiếp |
| Nghẹt thở | × 0.8 | MỘT 4 t tải trong một cuộn cảm cần một 5 t sling — the wrap grips as the load comes on |
| Rổ, chân gần thẳng đứng | × 2.0 | Both sides of the loop carry the load and the bearing face is doubled |
| Rổ, 7°–45° | × 1.4 | As the legs open the rating falls; plan the angle, không chỉ cân nặng |
| Rổ, 45°–60° | × 1.0 | At wide angles the basket advantage is gone — treat it as a straight lift |
Chiều dài: đường tròn, or the height you actually get
Một vòng khép kín không có điểm kết thúc, nên không có gì để đo lường từ đầu đến cuối. This trade quotes the same sling two ways, và chúng khác nhau khoảng hai lần: the circumference is the perimeter of the loop, while the effective working length is the usable height you get, roughly half the circumference because the loop is doubled when it hangs.
| Được trích dẫn như | Nó đo lường những gì | Cùng một chiếc địu bằng |
|---|---|---|
| Đường tròn | The perimeter of the loop — total band in the article | 2 tôi |
| Chiều dài làm việc hiệu quả | Chiều cao có thể sử dụng; the loop doubles when it hangs | 1 tôi |
Đặt tên cho quy ước bằng hình, hoặc thay vào đó hãy nêu cách sử dụng - chu vi của vật thể mà vòng lặp phải đi vòng - và sự mơ hồ biến mất trước khi dải được cắt.

Polyester, and the limits of it
The standard build is 100% polyester có độ bền cao (PES). It elongates no more than 3% at the working load limit and no more than 10% ở tải phá vỡ, so the load does not creep down as the lift comes on, and the standard build works from −40 °C to +100 °C. Nylon is offered where shock and abrasion dominate; polypropylene where weight and cost matter more than strength; UHMWPE and aramid where strength-to-weight or heat is the deciding factor.
What ends a polyester build is the same list as for any synthetic sling: heat above the range, strong alkalis, sharp edges that cut rather than abrade, and a cut or a glaze anywhere on the circumference. On a closed loop there is no second end to compare, so condition is judged against the surrounding band.

Marking and traceability
- TRONG 1492-1 capacity colour in the weave — violet 1 t, màu xanh lá 2 t, màu vàng 3 t, xám 4 t, màu đỏ 5 t, màu nâu 6 t, màu xanh da trời 8 t, quả cam 10 t.
- One black transverse stripe per tonne as a second, kiểm tra quang học trên chính ban nhạc.
- A sewn label with the working load limit, vật liệu, tiêu chuẩn, length and traceability code — and above 10 t, the label is the only rating there is.
- Every sling proof tested in our own laboratory before dispatch, with a test certificate per batch on request; mã HS 630790.

Thường xuyên hỏi
What does single ply mean, exactly?
One layer of webbing in the band the loop is made from — not two slings, and not two bands side by side. It gives a 4 mm section at the standard ladder widths, the lowest weight per metre in the range, and the most supple loop we build.
Is an endless sling seamless?
KHÔNG. It is endless in use, không liền mạch: the band is lapped over itself and closed with dense parallel stitching, and that lap is a full-strength joint in the load path. What a closed loop removes is the eyes and the end fittings, not the joint. If you need a closed loop with no joint in the load-bearing element at all, that is the dây đeo vòng vô tận, where the core is continuous.
How far up the capacity range does single ply go?
The single-ply ladder is published to 12 tại 7:1 in a 300 dải mm; the range as a whole runs to 30 t, and above the single-ply ladder the duplex build is the answer rather than a wider single band.
Can I use one loop for a vertical lift and a choke?
Đúng, and the figure changes with the arrangement: 1.0 thẳng đứng, 0.8 nghẹn ngào, 2.0 in a basket with the legs near vertical, rơi xuống 1.4 and then 1.0 as the legs open. Size to the hitch the crew will actually rig.
Will a single ply sling mark aluminium or painted steel?
Dải là sợi tổng hợp và không có khớp nối chạm vào tải, vì vậy nó sẽ không bị trầy xước hoặc va đập như cách mà dây xích hoặc dây cáp có thể làm. Width is the protection measure — for mirror-finish or anodised work, specify a width above the capacity ladder and the pressure on the surface falls with it.
How should the length be quoted?
Theo chu vi hoặc theo chiều dài làm việc hiệu quả - cả hai đều khác nhau khoảng hai lần. Đặt tên cho quy ước, or give the girth of the article the loop must go round, and the figure is confirmed on the order acknowledgement.
Yêu cầu báo giá
Five things settle a single ply loop
The load — what it is, its girth at the pick positions, and its surface;
The hitch — vertical, nghẹn ngào hoặc giỏ, and the leg angle if it is a basket;
The working load limit in that hitch, và yếu tố an toàn mà trang web của bạn hoạt động;
The length — with its convention, or the girth the loop has to go round;
The marking and packing — own-brand label, carton or pallet specification.
Đi đâu tiếp theo
- The endless lifting sling range — every closed form, compared by load;
- Dây đeo phẳng vô tận một lớp Và dây đeo phẳng vô tận polyester for the full size and weight tables;
- Double ply endless lifting sling where the capacity needs to go up at the same width;
- Dây treo web vô tận Và dây đeo vô tận for the type A article in full;
- Dây nâng ống thép for pipe duty, Và the one-way single ply version for single-trip export packing;
- Dây đai vải in all builds, Và contact.