Ngā Kāwai Hua

Synthetic Fiber Lifting Belt Slings

Whakaahuatanga Poto:

Lift sling rigging company produce Synthetic Fiber Lifting Belt Slings,synthetic lifting belt,Kotaha Whakarewa Hangaia,Heavy-Duty Lifting Belt.

Synthetic fibre lifting belt slings in polyester, nairona, PP, aramid and UHMWPE: flat belt or round, soft on finished surfaces, rated per hitch.

Taipitopito Hua

Lift sling rigging company produce Synthetic Fiber Lifting Belt Slings,synthetic lifting belt,Kotaha Whakarewa Hangaia,Heavy-Duty Lifting Belt.

Webbing sling · five fibres · flat belt and round

Synthetic Fiber Lifting Belt Slings

polyester, nairona, polypropylene, aramid and UHMWPE: the fibre decides whether the sling survives the job, and the form decides how it meets the load.

5 fibre types 0.5–24 t belt slings 1–50 t kotaha porotaka 200 °C aramid continuous
Orange synthetic fibre flat lifting belt sling with printed working load limit and length

A synthetic fibre lifting belt sling is a flat band — or a sleeved round sling — woven from high-tenacity man-made fibre, with eyes or a loop formed at the ends and the working load limit marked on the article. It replaces a wire rope sling wherever the load must not be marked: the band presents a wide, soft face instead of a hard line of steel, so the same load is spread over an area rather than concentrated on a few millimetres of contact.

Ko te kamupene Lift Sling Rigging te raranga te roopu, forms the eyes and proof-tests the sling in Taizhou. This page is about the part of the specification that decides whether a sling survives the job at all — the fibre — and about the two forms it is made into.

The one-line version. Polyester is the default, nylon takes shock, polypropylene handles chemicals and water, aramid takes heat, UHMWPE gives the most strength per kilo. Get the fibre wrong and the sling fails at something the tonnage never mentioned.

The two forms, from the same fibre family

The brief calls for flat belt or round slings, and both are built from the same fibres. The form changes how the load is contacted and how the sling is handled; it does not change what the fibre can survive.

Ripanga 1 — Flat belt sling against round sling
Flat webbing belt sling Kotaha porotaka (mutunga kore)
Whakawhitiwhiti roopu papatahi, 25–300 mm te whanui Porowhita, sleeved core, 30–100 mm diameter
Contact on the load Widest face; the least pressure per area Narrower line contact, but soft and compliant
Kei hea e pai ana Finished flat surfaces, pereti, coated sheet, bagged cargo Paipa, ngongo, mowhiti, anything that a flat band would crease on
Damage visibility Cuts and abrasion are visible on the face Damage hides inside the sleeve until it is severe
Te tohu Printed along the band, easy to read Label on the sleeve; colour on the sleeve
Typical rating 0.5 – 24 t me runga ake, per build 1 – 50 t me runga ake, per build
Green endless round sling, a sleeved core form of the same synthetic fibre family
Round sling form: the same fibre family inside a woven sleeve, for loads where a round, soft cross-section suits better than a flat band.

The five fibres, and what each one buys

Every synthetic sling on the market is one of a handful of fibres. They differ in strength per kilo, in how far they stretch, in the temperature they tolerate and in what chemicals attack them — and the differences are large enough to decide the application.

Ripanga 2 — Fibre selection for lifting belt and round slings
muka Te kaha / taumaha Totoro Te wera Chemicals and UV Kei hea te wikitoria
polyester (PET) Teitei Iti −40 ki +100 °C Good against acids; UV stable The default: hiki whānui, coated and painted work, colour-coded bands
Nylon (PA) Teitei Teitei (ka horo i te ru) Lower at the top end than polyester Ka whakaekea e te waikawa; moderate UV Nga kawenga ohorere, te whakahaere taratara, cargo that must settle into the sling
Polypropylene (PP) Whakaōrite Whakaōrite The lowest of the family Excellent against most chemicals and alkalis; mānu Wet docks, tipu matū, mahi mama, cost-sensitive work
Aramid Tino teitei Tino iti 200 °C tonu, 400 °C tihi Poor UV; moderate chemicals Mahi wera, foundry and steel plant, anything near heat
UHMWPE The highest per kilo Tino iti Low — heat is its weakness Good chemicals; poor at high temperature Maximum strength for minimum weight, long heavy lifts

Heat figures are the ones we publish for the aramid webbing; for the other fibres the limit depends on the build, and the label states what the article was rated to.

Two of these rows are worth reading twice. Aramid is the only fibre on the list that will stand in front of hot work — our aramid webbing is rated 200 °C continuous and 400 °C peak with an LOI of 28 or above — but it is also the weakest of the five in sunlight. UHMWPE gives the most strength for the least weight, and then fails earlier than polyester as the temperature climbs. Neither is a general-purpose substitute for the other.

White polyester webbing sling coiled on a bench with its 5 t capacity label visible
The same article coiled: a 5 t band weighs a few kilos, folds into a bag and needs no lifting gear to move it around the shop.

Why the soft face is the whole point

The reason a synthetic sling replaces a wire rope is geometry rather than strength. A 50 mm band and a 10 mm rope carrying the same 5 t present the same force over five times different a contact area — the band presses on the load at roughly a fifth of the pressure, and it does it with a woven surface instead of a steel one.

  • Kua peita, whakakikoruatia, coated and polished surfaces arrive at the other end as they left;
  • Bagged and boxed cargo is not cut through at the sling line;
  • No broken wires to catch a hand, no meat hooks, no kinking — the sling folds away;
  • A band of the same rating weighs a fraction of the rope and can be carried by one person.
White endless loop webbing sling laid out showing the woven band surface
Endless loop form: no eyes to wear, the load wraps anywhere along the band, and the weave is the same fibre throughout.

Matching the fibre to the environment

The tonnage is the easy part. What removes a synthetic sling from service is the environment, and the fibre is the only defence against it.

Ripanga 3 — Environment first, fibre second
Te taiao Fibre to specify He aha
General workshop, painted or machined work polyester Totoro iti, UV stable, the widest availability
Loads that land or swing Nylon Stretch absorbs the shock instead of passing it to the hook
Quay, wet dock, tipu matū Polypropylene Indifferent to water and to most chemicals; it floats
Next to heat, slag or hot plate Aramid The only fibre rated for continuous heat in this family
Maximum load for minimum weight UHMWPE Highest strength per kilo; accept the lower heat ceiling
Outdoor storage, long term polyester The most UV-stable of the five
Mixed or unknown duty polyester The safest default; specify up when the duty is known

Rating is per hitch, and the label wins

No synthetic sling has a single capacity. The marked working load limit applies to the arrangement it is used in, and the arrangement is what changes on the floor.

Ripanga 4 — Mode factors applied to the marked WLL
Whakaritenga Tauwehe He aha te tikanga
Poutū 1.0 Kotahi waewae, straight up — the marked figure
Kowaowaotia 0.8 Porowhitahia te kawenga me te hoki ki roto i tona ake kanohi
kete, 0–45° 2.0 Paihere i raro i te kawenga, waewae tata poutū
kete, 45–60° 1.4 Same basket, legs spread — the spread costs capacity
E rua nga waewae, 0–45° 1.4 A matched pair to one hook
E rua nga waewae, 45–60° 1.0 The pair with the legs spread
E toru, e wha nga waewae, 0–45° 2.1 Not three or four times the figure; the load rarely shares evenly
E toru, e wha nga waewae, 45–60° 1.5 The same arrangement, spread

The angle is measured from the vertical. The label on the sling overrides this table wherever the two disagree.

What a given width carries

Width is the other half of the specification: it sets the pressure on the load and the figure the band can be marked at. The ladder below is the one we publish for the standard build, so a quotation can be read against it.

Ripanga 5 — Belt width against working load limit, 7:1
Te rohe kawenga mahi Te whanui o te whitiki Usual ply Typical end
1 t 30 mm Takitahi Flat loop or folded eye
2 t 60 mm Takitahi Flat loop or folded eye
3 t 90 mm Takitahi Folded eye
4 t 120 mm Two-ply Folded or reinforced eye
5 t 150 mm Two-ply Folded or reinforced eye
6 t 180 mm Two-ply Te kanohi whakakaha
8 t 240 mm Two-ply Te kanohi whakakaha
10 t 300 mm Four-ply Te kanohi whakakaha

Read it with the mode factors above and a lift resolves quickly. A 6 t band in a vertical hitch is a 180 mm polyester belt with a reinforced eye. He pera ano 6 t in a choke is not: te 0.8 factor takes the capacity to 4.8 t, so the next size up carries it. Move the same job beside a furnace and the width stays but the fibre changes — aramid — because polyester would be the wrong answer however wide it is.

Where a synthetic sling must not go

Honesty here saves a load. The same softness that protects the cargo is what limits the article, and three conditions end it quickly:

  • Koi nga tapa me nga piriti. A cut band starts as a notch. Either the band is sleeved at the works, or the corner carries a pad — and the sleeve has to be ordered with the sling, because it cannot be retro-fitted to a woven band.
  • Heat beyond the fibre. Standard synthetic webbing fails by melting, kauaka ma te whakakino i te ahua. Above the working limit the answer is aramid, a heat sleeve, or a chain.
  • Chemicals the fibre cannot take. Acids attack nylon; strong alkalis and some solvents attack polyester. Where the load is wet with something aggressive, the fibre is chosen for that chemical, not for the tonnage.

How the sling is built and marked

  • The band is woven from high-tenacity fibre to the specified width, then cut and formed into eyes or a loop; multi-ply builds layer two or more bands for heavier working limits.
  • Eyes are folded and double-stitched in a pattern that puts the thread in shear; reinforced eyes add a wear layer where the hook sits.
  • Each sling is proof loaded before dispatch and fitted with a label carrying the working load limit, te roa, the fibre and the batch.
  • The band itself can be printed — WLL, roa, fleet number and your own brand — and the colour follows the market convention: 1 t puru, 2 t kakariki, 3 t kowhai, 4 t hina, 5 t whero, 6 t parauri, 8 t kahurangi, 10 t karaka. The colour is a quick check; the label is the answer.
White webbing sling with red reinforced eyes, takahurihia, showing the protected eye ends
Nga kanohi whakakaha: the end is where a band wears out first, so the eye is built up rather than left as a plain stitch line.

Te tirotiro me te reti

  • Read the label before the lift and confirm the sling is rated for the arrangement in use;
  • Check the whole band for cuts, mahanga, werohanga, abrasion, heat glazing and chemical staining — an acid or caustic burn is a retirement, not a stain;
  • Check the eyes and the stitching most carefully: broken or worn stitching retires the sling;
  • Check for distortion of the eyes or fittings after an overload;
  • Rokiroki ma, kia maroke, i waho o te ra, and keep the record with the sling.
Bundle of yellow webbing slings coiled, the colour used for the 3 t karaehe
Colour coding by capacity: yellow is the 3 t class by the market convention — useful on a yard, never a substitute for the label.

He maha nga patai

Which fibre should I take for a general workshop?

polyester, unless the duty says otherwise: it stretches little, tolerates UV far better than aramid or UHMWPE, and is available in every width and rating. Move to another fibre only when a specific condition — shock, werawera, matū, weight — rules polyester out.

Aramid or UHMWPE for a hot application?

Aramid. It is rated 200 °C continuous and 400 °C tihi; UHMWPE has the lowest heat ceiling of the family, so it is the wrong answer next to hot work however strong it is.

Can a round sling replace a flat belt sling?

On pipe, ngongo, rings and anything that a flat band would crease on, yes — and it is often kinder. On flat finished surfaces the belt gives the wider contact. Both are made from the same fibres, so choose the form by the load’s shape, ehara i te tone.

Does the colour tell me the fibre?

Kao. Colour codes the working load limit by convention, not the material — a yellow sling is 3 t whether it is polyester or nylon. The fibre is on the label.

Why does my nylon sling stretch so much?

Because nylon stretches further before it parts, which is exactly why it is chosen for shock loads: the stretch absorbs the jolt instead of passing it into the hook and the crane. Where a level load matters more than shock, polyester is the better fibre.

Can these slings be used outdoors?

Polyester and polypropylene yes, with normal care; aramid and UHMWPE degrade in prolonged sunlight, so they are stored out of it. In every case, inspect for condition rather than against a calendar.

Tonoa he korero

Tukuna te kawenga, ehara i te tone anake

The load — what it is, what its surface is worth, and how it will be hitched;

The figure — working load limit needed, and the arrangement it will be used in;

The environment — heat, matū, wai, rā, abrasion, koi nga tapa;

The form — flat belt or round sling, and the end type: flat loop, folded or reinforced eye;

The marking — WLL, roa, fleet number and your own brand if you need them printed.

Send the duty and the figure for a quotation →

Me haere ki hea

Kamupene Rigging Kotaha Kotaha · Lifute Industrial Park, Taizhou City, Porowini o Jiangsu, Haina · Waehere HS 630790
Waea +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Waiho To Karere

Panuku ki Runga