产品分类

Steel Pipe Lifting One Way Webbing Sling

简短描述:

Lift sling rigging company produce Steel Pipe Lifting One Way Webbing Sling,Lifting Slings For Steel and Steel Tube.

One-way webbing sling for steel pipe and tube: 25-300 毫米聚酯纤维, 1-24 t, 目不转睛或无穷无尽, cut to your pick spacing. Printed to your reference.

产品详情

Lift sling rigging company produce Steel Pipe Lifting One Way Webbing Sling,Lifting Slings For Steel and Steel Tube.

One-way sling · eye and eye · steel pipe and tube

Steel Pipe Lifting One Way Webbing Sling

两只眼睛, 两个选择, one journey — a flat woven band cut to the pick spacing of the lift and printed with the tonnage it will carry.

1–24 吨 WLL range 25–300 毫米 带宽 ×1.4 two legs to 45° ±2 % length tolerance
steel pipe lifting one way webbing sling carrying a galvanised pipe bundle

This is the eye-and-eye form of the one-way sling, and it is the form that suits most steel pipe and tube consignments: a flat polyester band with a formed eye at each end, one eye on each hook, the band bearing under the pipe or round the bundle. It is bought against a consignment rather than issued from a sling store, and it goes with the load instead of coming back. Working load limits run from 1 到 24 t, band widths from 25 毫米至 300 毫米, 和长度从 0.5 米至 100 米, at a factor of 5:1, 6:1 或者 7:1.

快速解答: for pipe the sling is specified by the pick positions. The length is the distance from the hook down to each pick, the capacity is set by the angle the legs make with the vertical, and the width is set by what the pipe surface will tolerate. Tonnage alone does not describe the article.

两只眼睛, 两个选择, and what that decides

The same one-way discipline is sold in three shapes, and the shape is decided by what is at each end of the band. On pipe work the eye-and-eye form is the general answer because a pipe is usually picked at two points along its length, with something to hook to above each one.

桌子 1 — The three shapes a one-way sling is bought in, for pipe work
Shape What is at each end How the pipe is held When it is the right buy
Eye and eye — this page A formed flat eye, stitched and bar-tacked One eye on each hook, band under the pipe or round the bundle Two picks along the length, with a hook, pin or shackle above each
无限循环 Nothing — a closed ring Wrapped round the pipe and back through itself, or doubled as a basket Where there is no fitting to thread and the band must close on itself
单眼 One eye and a plain tail 窒息: the tail passes back through the eye and the noose closes Where the pipe must be gripped rather than hung, or left slung on arrival

The single-eye version is written up separately, because a choke changes both the arithmetic and the length: 看 one way endless lifting slings, 单眼, for steel pipe and tubing. The endless loop is for the same loads with no hardware at either end — the closed-ring form is on its own page as well. Nothing prevents a consignment using more than one shape, but each has to be specified and counted separately.

The figure on the band is per leg — the angle decides what a pair will carry

A two-leg lift is never twice one sling. The legs lean towards each other, so each leg carries more than half the load and the pair carries less than two bands’ worth. The design factor table used for synthetic webbing slings states it plainly, and the reference angle is measured from the vertical, not between the legs.

桌子 2 — Mode factor by arrangement, and what a 5 t sling becomes
安排 角度 因素 容量
单腿, 垂直的 — × 1.0 5,000 公斤
两条腿 0与垂直方向 –45° × 1.4 7,000 kg per pair
两条腿 45与垂直方向 –60° × 1.0 5,000 kg per pair
两条腿 beyond 60° not permitted —
篮子, both parts vertical 0° × 2.0 10,000 公斤
篮子, parts at 45–60° — × 1.4 7,000 公斤
窒息 — × 0.8 4,000 公斤

Worked case. 一个 9 t joint of 508 mm pipe, picked at two points, 钩 4 m above the pipe, pick spacing 6 米. Each leg is √(3² + 4²) = 5.0 m long and makes 36.9° with the vertical, so the pair is worth 1.4 × 工作寿命. To carry 9 t the slings must be rated 9 ÷ 1.4 = 6.4 t each, 和一个 7 t band is the answer. Halve the hook height and the same pipe needs 9 t bands — the pipe did not change, the geometry did.

steel pipe suspended on two one way webbing slings in a workshop
两条腿, one pick near each end: the arrangement this page is written around.

Where the picks go on a pipe

A pipe is a beam, and where it is supported decides whether it sags, whips or bends at the overhang. The classical layout for a uniform span puts the supports at about 0.21 L from each end, which makes the sag in the middle equal to the overhang at the ends; many yards simply use the quarter points, which is close enough on a stiff wall and easier to measure. Neither figure is a rule from a standard — it is a layout, and the layout is what the sling length is cut to.

桌子 3 — Pick layout by joint length (single joint, 两个选择)
Pipe length Pick position from each end Span between picks 笔记
最多 6 米 1.5 米 (quarter points) 3 米 两个精选, one hook or two
6 – 12 米 0.21 L, 或者 2 最小米 0.58 L The usual range for line pipe
12 – 18 米 0.21 L 0.58 L Four picks or a spreader above
超过 18 米 Two pick groups — Spreader beam rather than a long V
捆绑包 One pick per sling position Set by the pack Girth, not length, sets the band
pick positions marked on a coated steel pipe before lifting
The pick positions marked on the pipe itself: the only instruction that still exists at the far end of the journey.

Two practical points that decide more lifts than the table does. A pick must not sit on a weld seam or a coating repair, and it must clear the end collar: an end that is thicker than the barrel will take the band on its shoulder and cut it. On a joint with a bevelled or sheared end, the band goes behind the bevel, never on it.

webbing sling in a basket hitch around a bundle of steel tubing
A basket hitch on tube: two parts of the band share the load, provided both are vertical. Lean them and the pair stops being worth twice one.

Length from pick spacing and hook height

On a two-leg lift the band is not a height, it is a hypotenuse. Given the spacing between the picks and the height of the hook above the pipe, the leg length and the angle follow directly — and the angle, 不是吨位, is what changes the capacity of the pair.

Leg length = √((spacing ÷ 2)² + hook height²), 和 angle from vertical = arctan((spacing ÷ 2) ÷ hook height). Add the eye take-up at both ends — roughly the eye clear length — and order to the next half metre. A sewn article holds ±2 % on length.

桌子 4 — Leg length and capacity for a pair of 5 t吊带
Pick spacing Hook height 腿长 Angle from vertical Pair capacity
4 米 4 米 4.47 米 26.6° 7,000 公斤
6 米 4 米 5.00 米 36.9° 7,000 公斤
8 米 5 米 6.40 米 38.7° 7,000 公斤
10 米 4 米 6.40 米 51.3° 5,000 公斤
12 米 5 米 7.81 米 50.2° 5,000 公斤
12 米 7 米 9.22 米 40.6° 7,000 公斤
16 米 6 米 10.00 米 53.1° 5,000 公斤
16 米 9 米 12.04 米 41.6° 7,000 公斤

The capacity column is the pair, not the leg, and it already includes the mode factor. Beyond 60° from vertical the arrangement is outside the factor table: raise the hook or shorten the spacing rather than adding tonnage.

This is why the same pipe can need two very different bands on two sites. A yard with a high gantry picks a 12 m joint with 5 T 腿; a shed with low headroom, picking the same joint at the same spacing, needs 7 t legs or a spreader to lift the pick points clear of the hook. The sling is the same length in both cases and a different article.

What the band bears on: 墙, coating and the end

The width of the band is chosen by the surface it touches, 不是按吨位. A pipe is a line contact with a curved, sometimes thin, sometimes coated face — and the failure on pipe work is nearly always local: a cut, a scuff or an ovalised wall at the pick, not a band that broke in the middle.

桌子 5 — Width and protection by pipe surface
管道 带宽 Protection at the pick 没有它会出现什么问题
Bare black pipe, 墙 6 mm and up 75 – 100 毫米 None normally needed Cosmetic scuffing only
Bare pipe, wall under 4 毫米 100 – 150 毫米 Wide band, pick behind the collar Ovalisation at the pick
涂层, painted or lined 150 毫米, 7.5 毫米带 穿套, 软接触 Coating damage becomes a rejection
Galvanised tube 100 – 150 毫米 Sleeve where the band turns Bright witness marks on the zinc
Bundled tube 150 – 200 毫米 Sleeve at the arris, if square-cut Band cut on a tube end
Stainless or aluminium 150 毫米, sleeve as standard 袖子, and a band that has never been used on steel Iron transfer, then corrosion

Two details cost almost nothing at the order and are impossible to add later: 一个 wear sleeve over the contact point, which is replaced with the band instead of the band being replaced, 和一个 强化眼 where a hook or shackle pin bears. On a one-trip article both are thrown away with the band, which is exactly why they are cheap.

pair of one way webbing slings with flat eyes for pipe lifting
眼睛和眼睛, 平织: 眼睛是带子向后折叠并缝合, so the hook bears on a soft flat loop rather than on an edge.
white polyester webbing sling with reinforced red eye
A reinforced eye in a sleeve where the hook bears. On pipe work it is the eye that wears first, 不是乐队.

规格

桌子 6 — Eye-and-eye one-way sling, 标准规格
范围 标准构造 笔记
织带 Flat woven high-tenacity polyester, 25–300 毫米 4 毫米或 7.5 毫米带
工作负荷极限 1 t – 24 每条吊带的吨数 垂直的, 单腿
设计因素 5:1 / 6:1 / 7:1 Same WLL needs a wider band at 7:1
结束 Formed flat eye at each end Stitched and bar-tacked; sleeved on request
Eye clear length 250 毫米于 1 到 650 毫米于 15 t Hook bowl or pin plus about 10 毫米
长度 0.5 米 – 100 米 Cut to the pick spacing; ±2 %
颜色 订购; 在 1492-1 code up to 10 t A second channel for sorting
温度 −40°C 至 +100 ℃ 聚酯纤维; not for molten metal
标记 WLL, 长度, 纤维, 批, 你的参考 Printed on the band and on a sewn label
包装 盘绕, baled or cartoned Can travel inside the consignment
海关编码 630790 Packing list line

The standard range

The works weaves nine tonnages on a 4 毫米带和九上 7.5 毫米带. Width follows the tonnage and the factor, and the minimum length steps up with the width rather than with the tonnage — which is the line that decides a short order.

桌子 7 — Width by WLL and factor, with minimum length
WLL 乐队 5:1 6:1 7:1 最小. 长度
1 t 4 毫米 25 毫米 50 毫米 30 毫米 0.5 米
2 t 4 毫米 50 毫米 100 毫米 60 毫米 1.0 米
3 t 4 毫米 75 毫米 150 毫米 90 毫米 1.0 米
4 t 4 毫米 100 毫米 200 毫米 120 毫米 1.5 米
5 t 4 毫米 125 毫米 250 毫米 150 毫米 1.5 米
6 t 4 毫米 150 毫米 300 毫米 180 毫米 1.5 米
8 t 4 毫米 200 毫米 200 毫米 240 毫米 2.0 米
10 t 4 毫米 250 毫米 250 毫米 300 毫米 2.0 米
12 t 4 毫米 300 毫米 300 毫米 300 毫米 2.0 米
2 t 7.5 毫米 25 毫米 50 毫米 30 毫米 0.5 米
4 t 7.5 毫米 50 毫米 100 毫米 60 毫米 1.0 米
6 t 7.5 毫米 75 毫米 150 毫米 90 毫米 1.0 米
8 t 7.5 毫米 100 毫米 200 毫米 120 毫米 1.5 米
10 t 7.5 毫米 125 毫米 250 毫米 150 毫米 1.5 米
12 t 7.5 毫米 150 毫米 300 毫米 180 毫米 1.5 米
16 t 7.5 毫米 200 毫米 200 毫米 240 毫米 2.0 米
20 t 7.5 毫米 250 毫米 250 毫米 300 毫米 2.0 米
24 t 7.5 毫米 300 毫米 300 毫米 300 毫米 2.0 米

Two lines of reading are worth doing before the table is used. The two blocks share the same width ladder, so a band bought thicker for a delicate surface buys nothing if the width column was already right — thickness is for tonnage and wear, width is for the surface. And at 8 t and above the 6:1 column runs out of width: from that point the band is already at 300 毫米, and the answer to more tonnage is a heavier block or two slings, not a wider band.

单程, and what that adds to the order

The band travels with the pipe, is inspected once at issue, and is not recovered. That changes three things about how it is ordered, and none of them about how it is made.

  • Counted per pick, 每包. A bundle on two picks is two bands; a long joint on four picks is four. Add 2–5 % for the band that gets cut while the pack is made up, and put the number on the order rather than in someone’s head.
  • Marked to the consignment. 工作负荷极限, length and your reference printed on the band — pack number, order number or part number — because that print is the only record the receiving site will have. 这 one way sling category sets out the discipline in full.
  • Packed to arrive with the goods. Coiled and baled, cartoned, or packed into the crate beside the pipe so the bands land at the same time as the consignment instead of a week earlier.

涉案检查

There is one inspection in the life of a one-way band and it happens before the lift. Four places, 按这个顺序:

  • The eyes. 拼接, bar-tacks and the mouth of each eye — a broken stitch at an eye gives no warning at the load.
  • The band where it will bear. 削减, 障碍, 玻璃受热, and any thin patch that shows daylight through the weave.
  • 印刷品. If the WLL or the length cannot be read, the band cannot be matched to the pipe it was cut for.
  • What it has been lying in. 砂砾, 切屑和油进入触点; a clean band is the only protection on the list that costs nothing.

常见问题

How many slings does a 12 m joint of pipe need?

二, at about 0.21 L from each end — 2.5 m in from either end, leaving a 7 m span — provided the wall carries the overhang. 以上关于 18 米, or where the overhang whips, four picks or a spreader beam is the honest answer and the band count goes up with it.

Can one sling lift one end of a pipe?

Only for a short, 僵硬的, light joint, and then it is a single vertical leg at 1.0 × WLL with the pipe hanging at an angle. On anything long the pipe rotates about the pick and the load walks; two picks are the arrangement, and the second sling is cheaper than the first accident.

眼睛和眼睛, endless loop or single eye for pipe?

Eye and eye where there is a hook or a pin at each pick — the usual case. The endless loop where nothing must be threaded and the band closes on itself, which is also the kindest to a coated surface. The single eye where the pipe must be gripped in a choke and left slung on arrival. The three are separate articles and are counted separately.

How flat is too flat?

Beyond 60° from the vertical the two-leg arrangement leaves the factor table entirely, and the tension in each leg climbs steeply for very little gain in height. If the pick spacing is fixed and the headroom is not there, the answer is a spreader beam that lifts the pick points instead of a heavier pair of slings.

Will the sling mark galvanised or coated pipe?

A used band can: grit embedded in the weave polishes the zinc, and a band that has carried black steel leaves iron behind that shows up as rust later. A sleeve at the contact point, a band kept for coated work only, 和 150 mm of width instead of 75 mm are the three measures that prevent it.

Can the length be cut to my pick spacing exactly?

Yes — that is what the length on the order means. Send the spacing between picks and the height of the hook above the pipe, and the leg length comes out of the arithmetic in Table 4; add the eye take-up and round to the next half metre. The finished length is confirmed in writing before the bands are cut, to ±2 %.

Send the lift, 不仅仅是吨位

Six lines and the band can be cut

The pipe: 外径, 壁厚, coating or finish, and whether it travels as a joint or a bundle;

The mass of one lift, and how many picks you intend to use;

The spacing between picks, and the height of the hook above the pipe;

The fittings at each pick — hook, shackle or pin — with their sizes;

The factor your market expects: 5:1, 6:1 或者 7:1;

打印参考, 颜色, 以及每包的数量.

Send the pipe and the pick spacing for a quotation →

起重吊索索具公司, 有限公司·利夫特工业园, 台州市, Jiangsu Province, 中国·HS编码 630790 · Tel / 微信 +86 180 6600 2268 ·702461526@qq.com

下一步去哪里

起重吊索索具公司 · Lifute Industrial Park, 台州市, Jiangsu Province, 中国·HS编码 630790
电话 +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com · xulft.com

 

留言

滚动至顶部