Awọn ẹka Awọn ọja

Single Ply Endless Lifting Sling

Apejuwe kukuru:

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Single ply endless lifting sling: one layer, one lapped joint, ko si opin. 4 mm iye, 1-12 t at 7:1 meji ỌKAN 1492-1, quoted by circumference or flat length.

Alaye ọja

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Endless lifting sling · single layer · 4 mm flat band

Single Ply Endless Lifting Sling

One layer, one lapped joint, ko si opin. The lightest closed loop in the range: it folds into a pocket, turns a tight radius and drapes over the load — 1 t lati 12 t at 7:1 meji ỌKAN 1492-1.

1–12 t single ply ladder 4 mm band section 7:1 meji ỌKAN 1492-1 25-300 mm band iwọn
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets

A single ply endless lifting sling is the single-layer build of the closed loop: one band of high-tenacity polyester, lapped over itself and closed with dense parallel rows of stitching, ti ko si oju, no fittings and no metal anywhere on the article. It is the endless type A flat woven webbing sling of EN 1492-1 — the type 5 web sling in North American usage.

The word to be careful with is ply. It does not mean two slings or two bands in parallel; it means how many layers of webbing are woven into the one band the loop is made from. Single ply is one layer, and everything that follows — the 4 mm section, the weight per metre, the way it turns round a small radius, and the capacity it can be given at a given width — comes from that one decision.

The trade-off in one line. Single ply gives the most flexible loop and the lowest weight per metre; duplex gives more capacity at the same width, a stiffer bearing face and more abrasion reserve. Ni isalẹ nipa 6 t, and wherever the loop has to fold, single ply is the right default.

What one layer actually gives you

Four practical differences separate the single-layer loop from the duplex build, and each one shows up on a different job:

  • A 4 mm section. The band folds into a pocket, coils onto a hook and passes between a load and a tight gap where a thicker band will not go.
  • Less weight per metre. The ladder below runs from 0.20 kg/m ni 1 t lati 2.05 kg/m ni 10 t — a one-handed carry for the sizes most yards actually use.
  • More supple over a radius. One layer conforms to pipe, tube and rolled sections instead of standing off them, so contact is over the full width rather than at two edges.
  • One joint, thin and easy to read. The lapped joint is the only made connection in the load path; in a single layer the stitching rows sit on one visible face, with no second layer masking them.
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets
Plate and sheet in a basket: one layer of band, doubled under the load, a full-width soft bearing face and no fitting anywhere near the steel.

Single ply against duplex, at the same width

The two builds are not two grades of the same thing; they are two answers to different questions. The comparison below is the one we use in quotation, and the widths are the published single-ply ladder.

Tabili 1 — Single ply and duplex, same nominal width
Ẹyọ ẹyọkan Duplex
Layers in the band Ọkan Meji, woven as one band
Section thickness 4 mm at the standard ladder Roughly twice the single-ply section
Capacity at a given width The ladder figure Higher — the reason duplex exists above the single-ply range
Iwọn fun mita kan 0.20 kg/m ni 1 t lati 2.05 kg/m ni 10 t Higher for the same width
Mimu Folds small, turns a tight radius, drapes onto the load Difa; sits flatter over an edge and resists abrasion longer
Ibi ti AamiEye Ni isalẹ nipa 6 t, tight gaps, small diameters, mixed rigs High capacity in a narrow width, rough edges, heavy abrasion
Apapọ One lap, stitching visible on the face One lap through the doubled band

The duplex build has its own page: double ply endless lifting sling.

The capacity ladder, nikan ply

Working load limits are quoted in straight lift, ni 7:1 meji ỌKAN 1492-1. Colour follows EN 1492-1 and is a capacity band, not a material; loke 10 t there is no colour code and the label is the only rating.

Tabili 2 — Single ply endless sling: agbara, colour and weight
WLL, gígùn gbe soke Àwọ̀ Iwọn itọkasi Iwọn gigun Isunmọ. iwuwo Ti parun (× 0.8)
1 t Awọ aro Jẹrisi lori ibere 0.5 – 100 m 0.22 kg/m 0.8 t
2 t Alawọ ewe 50 mm 1 – 100 m 0.35 kg/m 1.6 t
3 t Yellow 75 mm 1 – 100 m 0.52 kg/m 2.4 t
4 t Grẹy 100 mm 1.5 – 100 m 0.80 kg/m 3.2 t
5 t Pupa 125 mm 1.5 – 100 m 0.85 kg/m 4.0 t
6 t Brown 150 mm 1.5 – 100 m 0.96 kg/m 4.8 t
8 t Buluu 200 mm 2 – 100 m 1.34 kg/m 6.4 t
10 t ọsan 250 mm 2 – 100 m 1.64 kg/m 8.0 t
Loke 10 t Ko si koodu awọ Duplex build Lati paṣẹ Lori ìbéèrè Aami akoso

Widths and weights are the published series for this range; the finished width, ply and weight are confirmed on the order acknowledgement.

Ìbú, safety factor and the same capacity

A higher safety factor needs a wider band for the same working load limit, ti o jẹ idi ti awọn iwọn iwe ni o ni meta iye. Tell us the standard your site works to and the sling is built to it; the figures below are the single-ply polyester ladder.

Tabili 3 - Band iwọn nipa ailewu ifosiwewe, 4 mm poliesita ply nikan
WLL Ni 5:1 Ni 6:1 Ni 7:1 Sisanra Iwọn ni 7:1
1 t (1 000 kg) 25 mm 25 mm 30 mm 4 mm 0.20 kg/m
2 t (2 000 kg) 50 mm 50 mm 60 mm 4 mm 0.60 kg/m
3 t (3 000 kg) 75 mm 75 mm 90 mm 4 mm 0.78 kg/m
4 t (4 000 kg) 100 mm 100 mm 120 mm 4 mm 0.90 kg/m
5 t (5 000 kg) 125 mm 125 mm 150 mm 4 mm 1.14 kg/m
6 t (6 000 kg) 150 mm 150 mm 180 mm 4 mm 1.33 kg/m
8 t (8 000 kg) 200 mm 200 mm 240 mm 4 mm 1.85 kg/m
10 t (10 000 kg) 250 mm 250 mm 300 mm 4 mm 2.05 kg/m
12 t (12 000 kg) 300 mm 300 mm 300 mm 4 mm 2.70 kg/m
Four single ply endless slings in white, aro, green and black
The capacity colour is woven in, not printed on: white for the general band, violet for 1 t, green for 2 t, with one black transverse stripe per tonne as a second check.

Awọn isẹpo, and why it is the first thing to look at

Sling ailopin ko ni opin ni lilo, kii ṣe lainidi. Awọn iye ti wa ni lapped lori ara ati ni pipade pẹlu ipon ni afiwe awọn ori ila ti stitching; ipele yẹn jẹ isẹpo ti o ni kikun ati pe o joko ni ọna fifuye. O jẹ asopọ nikan ti a ṣe ni gbogbo nkan naa.

On a single-layer loop that joint is easier to inspect than on a duplex one, because the stitching rows lie on one visible face rather than between two layers. Look for broken or pulled stitches, a lap that has started to open, and abrasion where the lap passes over an edge. If the joint is sound, the rest of the loop is one continuous band and can be read anywhere along its length.

White single ply endless sling laid out on gravel
Ẹgbẹ kan, lapped and stitched once. That single joint is the only made connection in the load path, and the first thing an inspector reads.

Three hitches from the same loop

The marked figure is the straight-lift rating; every other arrangement is derived from it. Iwọn sling si hitch awọn atuko yoo kosi rig, kii ṣe si ọkan ninu eto gbigbe.

Tabili 4 — Mode factor by hitch
Hitch Ipo ifosiwewe Ohun ti o tumo si lori ojula
Inaro × 1.0 The label figure applies directly
Ti parun × 0.8 A 4 t fifuye ni a choke nilo a 5 t sling — the wrap grips as the load comes on
Agbọn, ese nitosi inaro × 2.0 Both sides of the loop carry the load and the bearing face is doubled
Agbọn, 7°–45° × 1.4 As the legs open the rating falls; plan the angle, not only the weight
Agbọn, 45°–60° × 1.0 At wide angles the basket advantage is gone — treat it as a straight lift

Gigun: iyipo, or the height you actually get

Yipo pipade ko ni opin, so there is nothing to measure end to end. This trade quotes the same sling two ways, nwọn si yato nipa nipa kan ifosiwewe ti meji: the circumference is the perimeter of the loop, while the effective working length is the usable height you get, roughly half the circumference because the loop is doubled when it hangs.

Tabili 5 — The same sling under both conventions
Ti sọ bi Ohun ti o ṣe iwọn Kanna sling dogba
Ayika The perimeter of the loop — total band in the article 2 m
Munadoko ṣiṣẹ ipari Giga to wulo; the loop doubles when it hangs 1 m

Lorukọ apejọpọ pẹlu eeya naa, tabi ṣalaye lilo dipo - girth ti nkan naa lupu ni lati yika - ati pe aibikita parẹ ṣaaju ki o to ge ẹgbẹ naa.

Green single ply endless sling with its blue capacity label
Aami sewn n gbe opin fifuye ṣiṣẹ, ohun elo, boṣewa, the length and the batch — on a closed loop it is the whole record of the article.

Polyester, and the limits of it

The standard build is 100% poliesita ti o ga (PES). It elongates no more than 3% at the working load limit and no more than 10% ni fifuye fifọ, so the load does not creep down as the lift comes on, and the standard build works from −40 °C to +100 °C. Nylon is offered where shock and abrasion dominate; polypropylene where weight and cost matter more than strength; UHMWPE and aramid where strength-to-weight or heat is the deciding factor.

What ends a polyester build is the same list as for any synthetic sling: heat above the range, strong alkalis, sharp edges that cut rather than abrade, and a cut or a glaze anywhere on the circumference. On a closed loop there is no second end to compare, so condition is judged against the surrounding band.

Single ply endless slings lifting bundles of steel pipe at a loading bay
Pipe bundles at a loading bay: the loop is passed round the bundle and both sides come back to the hook, so the band is doubled where the load is heaviest.

Marking and traceability

  • IN 1492-1 capacity colour in the weave — violet 1 t, alawọ ewe 2 t, ofeefee 3 t, grẹy 4 t, pupa 5 t, brown 6 t, buluu 8 t, ọsan 10 t.
  • One black transverse stripe per tonne as a second, opitika ayẹwo lori awọn iye ara.
  • A sewn label with the working load limit, ohun elo, boṣewa, length and traceability code — and above 10 t, the label is the only rating there is.
  • Every sling proof tested in our own laboratory before dispatch, with a test certificate per batch on request; HS koodu 630790.
Two single ply yellow endless slings showing the flat band and its thin section
The single-layer section is 4 mm: it folds into a pocket, turns round a small diameter and drapes over the load instead of standing off it.

Nigbagbogbo beere

What does single ply mean, exactly?

One layer of webbing in the band the loop is made from — not two slings, and not two bands side by side. It gives a 4 mm section at the standard ladder widths, the lowest weight per metre in the range, and the most supple loop we build.

Is an endless sling seamless?

Rara. It is endless in use, kii ṣe lainidi: the band is lapped over itself and closed with dense parallel stitching, and that lap is a full-strength joint in the load path. What a closed loop removes is the eyes and the end fittings, not the joint. If you need a closed loop with no joint in the load-bearing element at all, iyẹn ni ailopin yika sling, where the core is continuous.

How far up the capacity range does single ply go?

The single-ply ladder is published to 12 t at 7:1 in a 300 mm iye; the range as a whole runs to 30 t, and above the single-ply ladder the duplex build is the answer rather than a wider single band.

Can I use one loop for a vertical lift and a choke?

Bẹẹni, and the figure changes with the arrangement: 1.0 inaro, 0.8 fun pa, 2.0 in a basket with the legs near vertical, ja bo si 1.4 and then 1.0 as the legs open. Size to the hitch the crew will actually rig.

Will a single ply sling mark aluminium or painted steel?

Ẹgbẹ naa jẹ okun sintetiki ati pe ko si ibamu fọwọkan fifuye naa, nitorina kii yoo yọ tabi burr bi ẹwọn tabi okun waya le ṣe le. Width is the protection measure — for mirror-finish or anodised work, specify a width above the capacity ladder and the pressure on the surface falls with it.

How should the length be quoted?

Nipa iyipo tabi nipa ipari iṣẹ ṣiṣe ti o munadoko - awọn mejeeji yatọ nipasẹ iwọn kan ti meji. Dárúkọ àpéjọpọ̀ náà, or give the girth of the article the loop must go round, and the figure is confirmed on the order acknowledgement.

Beere agbasọ ọrọ kan

Five things settle a single ply loop

The load — what it is, its girth at the pick positions, and its surface;

The hitch — vertical, choked tabi agbọn, and the leg angle if it is a basket;

The working load limit in that hitch, and the safety factor your site works to;

The length — with its convention, or the girth the loop has to go round;

The marking and packing — own-brand label, carton or pallet specification.

Send the duty and the figure for a quotation →

Ibi ti lati lọ tókàn

Gbe Sling Rigging Company · Lifute Industrial Park, Ilu Taizhou, Agbegbe Jiangsu, China · HS koodu 630790
Tẹli +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Fi ifiranṣẹ rẹ silẹ

Yi lọ si Top