Mahsulot toifalari

5 Ton Heavy Duty Ratchet Straps

Qisqacha tavsif:

Lift sling arma kompaniyasi ishlab chiqaradi 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

5 ton heavy duty ratchet straps: 50 mm polyester, 5,000 daN break, LC 2,500 daN dan EN gacha 12195-2. Zanglamaydigan 304/316 and aramid high-temp builds. To'g'ridan-to'g'ri zavod.

Mahsulot detali

Lift sling arma kompaniyasi ishlab chiqaradi 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

Cargo restraint · EN 12195-2

5 Ton Heavy Duty Ratchet Straps

50 mm poliester to'quv, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

2,500 Va bog'lash qobiliyati 5,000 Va sindirish kuchi 350 Va STF da 50 daN hand 3-10 m standard length
5 ton heavy duty ratchet straps with hook options: claw hook, tekis kanca, D ring and S hook

“5 ton heavy duty ratchet straps” is the phrase buyers search for, and the reason this page exists is that the phrase covers two different articles. a kuni 50 mm polyester assembly the breaking strength is 5,000 Va va bog'lash qobiliyati (LC) hisoblanadi 2,500 Va. Both numbers are real, both are printed on the same label, and quoting one against the other is how trailers get overloaded. We build the assembly to EN 12195-2, mark it, and state both figures so the comparison you make at quotation stage is between like and like.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 uchun 10 m standart sifatida, LC 2,500 Va, STF 350 va N da 50 va qo'l kuchi. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.

Part of the to'rli sling and lashing range. The 50 mm specification in isolation sits on the 50 mm 5000 kg ratchet bog'lovchi kamar sahifa.

What “5 Ton” Actually Means on a Ratchet Strap

Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. EN ostida 12195-2 bog'lovchi tasmaning to'ri bog'lash qobiliyatidan kamida ikki baravar ko'p bo'lishi kerak, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.

Jadval 1 — The three numbers on a 5 ton heavy duty ratchet strap
Rasm Value on the 50 mm assembly U nimani tasvirlaydi How it gets misread
Minimal buzilish kuchi 5,000 Va (5,000 kg) O'rnatishni tortish sinovida muvaffaqiyatsizlikka uchragan yuk Read as the working figure — the mistake that overloads a trailer
Bog'lash qobiliyati (LC) 2,500 Va (2.5 t) Assambleya ushlab turish uchun mo'ljallangan, printed on the label Ko'taruvchi slingning WLL bilan solishtirganda, which is a different duty altogether
Standart kuchlanish kuchi (STF) 350 va N da 50 va qo'l kuchi The tension one person reaches with the ratchet handle LC bilan chalkashib ketgan, Shunday qilib, operator foydali nuqtadan o'tishda davom etadi
Ask for both numbers. Two suppliers quoting “5 tonne” can be quoting the breaking strength and the working figure — a factor of two apart — and a North American catalogue printing the same article as “10,000 lb” is quoting breaking strength in pounds. Xuddi shu kamar, different unit, same trap.

Why the 50 mm Build Is the Heavy-Duty Default

Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. The 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.

Jadval 2 — Width ladder: where 50 mm sits
Veb kengligi Typical LC Buzilish kuchi Nima uchun sotib olinadi
25 mm (1 ichida) 400–500 daN 800–1,000 daN Tool boxes, light restraint, tight anchor eyes
35 mm (1-3/8 ichida) 750 Va 1,500 Va Van and trailer decks, general cargo
38 mm (1-1/2 ichida) 1,000–1,500 daN 2,000–3,000 daN Chelik plastinka, quvur to'plamlari, plant
50 mm (2 ichida) 2,500 Va 5,000 Va Heavy cargo restraint, bobinlar, mashinalar, konteynerlar
75-100 mm 5,000 daN and up 10,000 daN and up Abnormal loads, where the bed allows the width

The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.

Standard Specification of the 5 Ton Assembly

Jadval 3 — 50 mm 5 ton heavy duty ratchet strap: texnik parametrlar
Element Spetsifikatsiya
Webbing 100% yuqori chidamli polyester, dumaloq to'quv, UV stabillashgan, 50 mm ± 2%
Band qalinligi / massa 1.8 nominal mm / 88 g per metre
Bog'lash qobiliyati (LC) 2,500 va yig'ilish uchun
Minimal buzilish kuchi 5,000 Va (2:1 against LC)
Standart kuchlanish kuchi (STF) 350 va N da 50 va qo'l kuchi
Tensioner Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle
LC da cho'zilish 7% yoki kamroq
Xizmat harorati -40 °C gacha +100 °C (polyester to'r)
Standart uzunlik 3-10 m; 1–30 m to order
Belgilash Woven label: LC, STF, uzunligi, partiya raqami, standard reference
Standart Designed, tested and marked to EN 12195-2
HS kodi 630790

The End Fitting Decides Whether the Strap Fits the Job

The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.

Jadval 4 — End fittings for 5 ton heavy duty ratchet straps
O'rnatish Anchors to Notes before ordering
Chassis rave hook Flatbed side rail, chassis lip Check rail thickness and that the hook throat clears it
Claw hook Anchor rings, D rings, recessed eyes Opening must clear the ring; load on the crown only
D ring / delta ring Welded or bolted anchor points Ring bore at least as wide as the webbing
Flat snap hook Elektron trek, slotted rail, teshiklar Confirm slot width; snap gate must close fully
S hook Quvurlar, rails, frame members Both ends must seat without point loading on a weld
Sewn loop / looped ends Around the load or through a bore Nothing metal at the load; ideal for finished surfaces
Cheksiz, mos kelmaydi Girth only — hulls, bobinlar, to'plamlar See the endless loop build below
5 ton heavy duty ratchet straps with hook options: claw hook, tekis kanca, D ring and S hook
Bir 50 mm band, eight ways to terminate it — the hook option decides which anchor the strap can reach.

The 5 Ton Strap in Two Special Builds

Polyester covers most freight, and it fails predictably when it is out of its depth: atrofida yumshatadi 150 °C and melts at about 255 °C, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.

Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces

The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 yoki 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 va N da 25 mm gacha 2,500 va N da 50 mm, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.

The grade decision is about chloride, not load. 304 (1.4301) handles rain, fresh water, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 in the belief that it is stronger is paying for the wrong property. Ilova xavfsizlik bilan bog'liq bo'lsa, bahoni hisob-faktura tavsifida emas, balki tegirmon sertifikatida tasdiqlang.

Two shop-floor notes worth passing on. Zanglamaydigan po'latdan yasalgan iplar, so a dry 316 yong‘oq a ustiga qattiq yuguradi 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. Va sho'r suvda alyuminiyga zanglamaydigan murvat galvanik juftlikni hosil qiladi, so where the strap anchors to an alloy frame, kontaktni ajrating.

Full range and grade comparison: cheksiz zanglamaydigan po'latdan yasalgan tasma.

Aramid (Kevlar) ratchet straps — for heat, sparks and cut edges

Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 °C. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.

The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.

Two honest limits. Aramid is flame retardant, not fireproof: molten steel, ladles and hot slag still need a heat shield or a stand-off. And low elongation is exactly wrong for snatch and shock loads — for those, the polyester band or a dedicated recovery strap is the right article.

Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.

How Many Straps Does the Load Actually Need?

Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.

Jadval 5 — Worked example: 50 mm straps at 2,500 daN LC
Straps used Angle to the deck Restraint per strap Total restraint
2 45° taxminan. 1,750 Va taxminan. 3,500 Va
4 30° taxminan. 1,250 Va taxminan. 5,000 Va
4 45° taxminan. 1,750 Va taxminan. 7,000 Va
4 60° taxminan. 2,165 Va taxminan. 8,660 Va
6 45° taxminan. 1,750 Va taxminan. 10,500 Va

The arithmetic is an illustration, not a lashing plan: IN 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.

Qayerda 5 Ton Ratchet Strap Earns Its Keep

  • Yassi to'shak, container and plant trailer restraint — the volume application for the 50 mm build.
  • Chelik rulon, plita, billet and pipe bundles, with edge protection at the contact points.
  • Mashinasozlik, moulds and skid-mounted plant, qayerda a 25 mm strap has neither the width nor the tension.
  • Yog'och paketlar, sandiqlar va sandiqlar, including the endless form that simply closes round the pack.
  • Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
  • Dengizchi, marina and wash-down duty in 304 yoki 316 where plated hardware would be a maintenance item.
  • Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.
5 ton heavy duty ratchet straps securing a timber crate on a flatbed truck
50 mm straps over a timber crate on a flatbed — two legs at roughly 45°, hooks seated on the crown of the rail.

Rang, Printing and Private Label

Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, apelsin, sariq, qora, qizil, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, uzunligi, standard and traceability code. Cartons of 10 uchun 20 pieces, palletised for export, with neutral or own-brand packaging as required.

Sinov, Traceability and the Paperwork Buyers Ask For

Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. Sinov hisobotlari, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.

One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.

Tez-tez so'raladigan savollar

Bu a 5 ton ratchet strap rated to lift 5 tonnani tashkil etadi?

Yo'q, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.

Why does the same strap get called 5 tonna va 2.5 tonna?

Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.

50 mm yoki 38 mm for a flatbed?

50 mm, unless the anchor points are small. The 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; the 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.

Do I need 304 yoki 316 zanglamaydigan?

316 where chloride is present — sea air, tuz spreyi, muzdan tozalash tuzi, boatyards, oziq-ovqat o'simliklari. 304 is enough for rain, fresh water, condensation and indoor wash-down. The difference is corrosion resistance, kuch emas.

At what temperature does polyester fail, and what does aramid do instead?

Polyester softens around 150 °C and melts at about 255 °C, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 °C, and chars at about 427 °C instead of melting. Yuqorida 400 °C, or against molten metal, both need a heat shield.

Can the strap be supplied with a printed brand and a custom length?

Ha. Kengliklari, gacha 30 m, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.

Kotirovka so'rash

Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, atrof-muhit (salt, issiqlik, yuvish), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.

Lift Sling armatura kompaniyasi

Lifute sanoat parki, Tayzhou shahri, Jiangsu viloyati, Xitoy

Tel: +86 523 8693 5818 · WhatsApp: +86 180 6600 2268

Elektron pochta: 702461526@qq.com · HS code 630790

Send your lifting details for a quotation →

Tegishli mahsulotlar

Lift Sling armatura kompaniyasi · Lifute Industrial Park, Tayzhou shahri, Jiangsu viloyati, Xitoy · HS kodi 630790
Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com · xulft.com

 

Xabaringizni qoldiring

Yuqoriga aylantiring