Lift sling rigging company produce Aramid Anti-Drone Nets,knotted Aramid Anti-Drone Net,high strength Anti-Drone Net,Aramid Anti-Drone Net for Restricted Area Protection,Para Aramid Safety Net,Heavy Duty Aramid Fabric Netting for Anti-Drone Defense/Perimeter Protection/Security Facilities.
Ан aramid anti-drone net is a knotted rope panel hung across the line a small unmanned aircraft would fly through. We supply it as a complete assembly rather than a loose piece of netting: knotted aramid panel, spliced border, кути очей, tensioners and anchors, quoted per opening so that the panel, the border and the fixings carry the same load.
Two rope sizes cover almost every installation. А 6 mm braided aramid rope breaks at 2.6 t and is the panel for perimeter work, prisons, schools and anywhere the aperture has to be fine without the panel becoming heavy. А 10 mm braided aramid rope breaks at 7 t and is the panel for real kinetic impact — refineries, substations, порти, airfields. Both are knotted, both are spliced into the border, and both are supplied with the fittings that take the load out of the mesh and into the structure.
At a glance
- 6 mm braided aramid rope — breaking force 2.6 t
- 10 mm braided aramid rope — breaking force 7 t (70.67 kN measured on a 10 mm sample)
- Knotted mesh 40–120 mm, panels to 10 × 20 м
- Supplied with border, кути очей, tensioners and anchors
- No power, no radar, no operator — passive interception
- Не тане: вуглецьовується з о 400 °C and holds its shape
On this page
What the assembly is made of
Four elements decide whether the barrier works, і тільки одна з них - мотузка.
- The panel. A 12-strand braided aramid rope, double-knotted into square or diamond mesh. The knot gathers four rope ends, so the load entering from one direction leaves through the other three instead of passing through a clamp.
- Кордон. The same braid or one size up, double-laid and spliced — never knotted — around the perimeter. The border collects everything the mesh gathers and hands it to the corner eyes.
- The corner eyes and fixing points. Spliced eyes with stainless thimbles at the corners, eyelets or D-rings along the edge at your anchor spacing.
- Якоря. Posts, wall plates or stand-off brackets. A panel that is strong enough and tied to a post that is not will fail at the post.
The construction detail behind the knot, the braid and the fire behaviour is set out on the high strength anti-drone rope net сторінку; this page carries the specification and the fittings you need to place an order.
Технічні параметри
The figures below are the manufacturing range. The batch certificate supplied with the panel governs, and the installed barrier is only as strong as its border and anchors.
| Пункт | Aramid anti-drone net — standard build |
|---|---|
| клітковина | Параарамідні (Кевларового типу), УФ-стабілізований; polyester available for light duty |
| Мотузкова конструкція | 12-пасмо коса, coreless; 8-strand on 6 mm and below |
| Діаметр каната | 6 мм і 10 стандарт мм; 4 / 8 / 12 mm to order |
| Breaking force — 6 мм | 2.6 t (≈25.5 kN) |
| Breaking force — 10 мм | 7 t (≈68.6 kN; 70.67 kN measured on sample Dia10mm, 23 June 2026) |
| Подовження | ≈3.5 % на перерві; under 1.5 % при робочому навантаженні |
| Сітка | 40 / 50 / 60 / 80 / 100 / 120 мм, квадрат або ромб |
| Будівництво | Knotted, double knot hand-set and locked |
| Розмір панелі | 5 × 10 м, 10 × 10 м, 10 × 20 m as single panels; larger openings as joined panels |
| вага | ≈1.6 kg/m² at 10 мм / 100 мм сітки; ≈0.6 kg/m² at 6 мм / 100 мм |
| Теплові | Немає точки плавлення в експлуатації; continuous to ≈200 °C; carbonises from ≈400 °C |
| Колір | Натуральне арамідне золото, чорний, або на замовлення |
| Покриття | Без покриття, або ПУ / неопрен, змочений для УФ-променів та стирання на постійних зовнішніх панелях |
| Маркування | Позначте розмір панелі, діаметр мотузки, сітка, волокно і номер партії |
| обов'язок | Physical interception — never fall arrest, ніколи не піднімати |
Таблиця 1 — Aramid anti-drone net, standard build.
Кордон, fittings and anchor schedule
Buyers rarely fail on the panel and often fail on what it is tied to. The schedule below is what we supply with a standard opening; every line is confirmed on the approval drawing before the panel is woven.
| Пункт | Специфікація | матеріал / закінчити | Примітки |
|---|---|---|---|
| Border rope | 10 mm 12-strand aramid, double-laid, spliced | Арамід, optional PU dip | Never knotted — a knot in the border puts the panel through a single joint at its most loaded point |
| Corner eye | 80 × 160 mm spliced eye, stainless thimble | AISI 316 наперсток | One per corner as standard; extra eyes on long spans |
| Edge eyelets | Ø 12 мм, в 500 mm centres | Stainless, pressed | For lacing to a frame or to a second panel |
| D-ring / delta ring | Ø 12 мм, 60 × 110 мм | Zinc-plated or AISI 316 | Where a ratchet tensioner is used instead of a turnbuckle |
| Tensioner | M12 turnbuckle, або 50 mm ratchet tensioner | Galvanised / zinc-plated | Take the slack out and stop; over-tensioning creeps the knots |
| Anchor post | Ø 60 × 3.0 mm or Ø 76 × 3.0 mm tube, 3–6 m | Гаряче оцинкований | Base plate 200 × 200 × 10 мм, 4 × M16; post size to be confirmed against design wind |
| Wall / anchor plate | 150 × 150 × 8 мм, 4 × M12 | Гаряче оцинкований | For fixing to concrete or steel structure |
| Stand-off bracket | 300 / 500 / 1000 mm arm | Galvanised | Keeps 1 m clear behind the panel for a caught aircraft to deform into |
| Eye bolt | M12 × 120 мм | Galvanised | Anchor point at the post or wall |
| Wire rope clip set | M6 / M8 with thimble | Galvanised | For anchor tails and temporary fixings |
| Wear sleeve | 500 мм, open tubular | PU-coated polyester | Where the panel crosses structure or a sharp edge |
| Repair kit | 3 m matching braid + splicing fid | Арамід | One damaged mesh is re-knotted on site and recorded |
| Panel tag | 60 × 120 мм | Woven polyester | Розмір панелі, мотузка, сітка, клітковина, номер партії |
Таблиця 2 — Fittings supplied with a standard opening. Load ratings of anchors and tensioners are confirmed against the panel design on the approval drawing.
Aramid against steel wire mesh
Steel wire mesh is the barrier most buyers compare against, and the comparison is usually made on the wire. It should be made on the joint. A clamped stainless mesh is pressed together with aluminium double ferrules, one at every crossing, and the ferrule — not the wire — sets the limit of the panel.
The following is the specification the steel mesh trade works to, translated from the Chinese original supplied with the material.
| Ø мотузки (мм) | Strand | Ferrule joint, min. breaking force | кН | тонн |
|---|---|---|---|---|
| 1.2 | 7 × 7 | not published for mesh joints | — | — |
| 1.5 | 7 × 7 | ≈41 kgf (≈400 N) | 0.4 | 0.04 |
| 1.6 | 7 × 7 | not published for mesh joints | — | — |
| 2.0 | 7 × 7 | ≈265 kgf | 2.6 | 0.27 |
| 2.4 (3/32″) | 7 × 7 | ≈426 kgf (4.18 кН) | 4.18 | 0.43 |
| 3.0 | 7 × 19 | ≈552 kgf | 5.4 | 0.55 |
| 4.0 | 7 × 19 | ≈981 kgf | 9.6 | 0.98 |
| 6 / 8 / 10 / 12 | 7 × 19 | no ferrule rating published for mesh joints | — | — |
Таблиця 3 — Stainless steel wire rope mesh, aluminium double ferrule to DIN EN 13411-3, SUS 304 / 304L / 316 / 316L. Ferrule joints must not be bent again or re-used after pressing; for dynamic, impact or personnel duty the working load is taken as 1/5 до 1/6 of the breaking force.
Steel wire mesh: a pressed aluminium ferrule at every crossing. The largest standard ferrule breaks at about 0.98 t — and that joint repeats across the whole panel.
Put the two tables side by side and the difference is not marginal.
| Element | Breaking force | Against the 4.0 mm ferrule |
|---|---|---|
| 10 мм арамідна мотузка, вузлуватий | 7 t (≈68.6 kN) | 7.1 × |
| 10 mm aramid, в 50 % knot efficiency | ≈3.6 t (35 кН) | 3.7 × |
| 6 мм арамідна мотузка, вузлуватий | 2.6 t (≈25.5 kN) | 2.7 × |
| 4.0 mm steel wire + aluminium ferrule | 0.98 t (9.6 кН) | 1.0 × |
| 3.0 mm steel wire + aluminium ferrule | 0.55 t (5.4 кН) | 0.56 × |
Таблиця 4 — Like for like: one element of net against one element of net.
Even the lightest rope we put in an anti-drone panel — 6 мм, 2.6 t — carries 2.7 times the load of the heaviest ferrule in the steel table, and it does so at roughly a tenth of the weight per square metre. The gap matters for a second reason: a steel mesh repeats its weakest joint hundreds of times across an opening, so a drone finds the nearest one, while a knotted panel spreads the impact through neighbouring meshes and degrades instead of unzipping.
Steel mesh is still the right answer for rigid screens, heavy debris and abrasion, and we make wire rope assemblies on the same presses — see канатні стропи. It is not the right answer for a fast, light aircraft, because the ferrule sets the limit at about a tonne.
Choosing rope and mesh
Two decisions, в такому порядку: what has to be stopped, then what has to be seen through.
| Situation | Мотузка | Сітка | чому |
|---|---|---|---|
| Perimeter screening, prisons, школи, events | 6 мм | 60–80 mm | світло, low wind area, deployable by two people; the threat is a small multirotor or a contraband drop |
| Substations, data centres, fuel points | 10 мм | 80–100 мм | Real kinetic impact and a dropped payload; needs the joint strength and the fire behaviour |
| Refineries, tank farms, hot process areas | 10 мм | 80–100 мм | Panel must not melt or drip; aramid carbonises and holds its geometry |
| Airfields, helipads, approach zones | 10 мм | 100–120 mm | Larger airframes; wind load usually governs the anchors rather than the aircraft |
| Fine screens, іскри, small debris | 6 мм | 40–50 мм | Aperture smaller than the smallest part that must not pass |
Таблиця 5 — Selection guide. Where the fire case governs rather than the impact, see протипожежна протипожежна сітка.
Installation and stand-off
- Протистояння. Keep at least 1 м чистий за панеллю. A caught aircraft has to deform into space, not into the asset.
- Відстань між анкерами. 2 м або ближче по кордону. The border spans between anchors and carries everything the panel collects.
- Напруга. Take the slack out and stop. Вузлова арамідна панель схоплюється під першим навантаженням; over-tensioning creeps the knots and works the anchors loose.
- Повернення даху. A vertical wall can be flown over. Anything above about 6 м потребує повернення або верхньої штори.
- No cut mesh. Never cut an aperture for access or a service. Put a reinforced opening on the drawing.
- Вітер. А 100 мм нетто це приблизно 30 % solid; розрахувати панель як пористу поверхню при місцевому базовому тиску вітру, and size the posts to that, not to the drone.
Маркування, packing and documents
Each panel is rolled, strapped and tagged, with the tag carrying panel size, діаметр мотузки, сітка, волокно і номер партії. Panels travel in a PVC bag inside a woven outer, or on a pallet for multi-panel orders. Batch test records, a packing list and a declaration of conformity are supplied with the shipment; state the standard your site or customs authority needs and the documents are prepared to it.
код HS 630790. Походження: Lift Sling Rigging Co., ТОВ, Індустріальний парк Ліфуте, Місто Тайчжоу, Провінція Цзянсу, Китай.
Questions buyers ask
How strong is an aramid anti-drone net against a steel wire mesh?
А 6 mm aramid rope breaks at 2.6 t and a 10 мм при 7 t. The largest standard ferrule on steel wire mesh — 4.0 mm rope — breaks at 981 kgf, приблизно 0.98 t. On joint strength the 10 mm aramid element carries about seven times the best steel mesh joint, and even the 6 mm element carries 2.7 times as much.
What mesh size do I specify?
40–60 mm for small multirotors, so a propeller blade cannot pass; 80–100 mm for larger multirotors and fixed-wing airframes; 120 mm where panel weight and wind area matter more than aperture. The rule is that the aperture must be smaller than the part that would arrive first, вимірюється між центрами канатів, якщо не вказано вільний отвір.
Is it a panel or a complete assembly?
A complete assembly: knotted panel, spliced border, corner eyes with stainless thimbles, edge eyelets where specified, tensioners and anchors, tagged and documented. Panels can be supplied loose where you already have the anchors and only need the net.
Will it stop a drone carrying a munition?
The net stops the delivery, not the warhead, and that is the whole point of netting a position. А 5 kg munition arriving at 100 m/s is arrested with about 62.5 kN if it is stopped over 0.4 м; shared across the four ropes of an engaged mesh that is roughly 16 kN per rope, against about 34 kN carried by a knotted 10 mm element even at 50 % knot efficiency. Break the delivery and the warhead never arrives.
Can a damaged panel be repaired on site?
Yes on knotted construction. One damaged mesh is re-knotted with the same braid and the repair is recorded. Пошкоджена прикордонна мотузка, a pulled corner eye or a large damaged area is replaced rather than patched.
Does the net need power or detection?
немає. It is a passive physical barrier: no power, no radar, no operator. That is also why it still works against fibre-optic and pre-programmed drones that electronic countermeasures cannot reach.
Супутні товари
- High strength anti-drone rope net — the engineering behind the knot, the braid and the joint
- Арамідна сітка з вузлами — construction options and strength per braid
- Fire prevention anti-drone mesh — where flame, not impact, governs the fibre
- Durable safety netting for fall protection — the same netting tradition where a person has to be caught
- Страхувальні мотузкові сітки — the full category, з панелями, сітки та крайові деталі
- Нейлонова мотузка and braided aramid rope — the line our panels are knotted from
Надішліть відкриття, get a panel you can install
Tell us the width and height of the opening, what the panel fixes to and at what spacing, the stand-off behind it, the aircraft you are designing against and the design wind speed. Повертаємося з діаметром мотузки, сітка, border specification, fittings list and price — with the breaking force at the knot, не тільки на котушці.
Електронна пошта : lift98@jslift.com· Telephone and WeChat +8618066002268