Multi-ply Webbing Sling

A multi-ply webbing sling is two, three or four layers of high-tenacity polyester webbing sewn into one load-bearing band. The plies are stacked and stitched through, so the cross-section that carries the load is the width multiplied by the number of plies – which is why a multi-ply sling reaches in 100 mm what a single layer needs 240 mm to reach. Standard build: 2, 3 veya 4 kat, 100-300 mm wide, 8 t'ye 48 T per leg in the vertical mode at a 7:1 faktör, elongation of 7 % or less çalışma yükü sınırında, derecelendirildi İÇİNDE 1492-1 and made to order in any length from 1 m ila 100 M.

Ne “Multi-Ply” Actually Adds

Capacity in a flat sling is set by the cross-section of load-bearing yarn, and the cross-section is width x plies. There are only two ways to buy a figure: go wider, or go deeper. Going deeper is what this page is about.

• More capacity in the same width. A 100 mm band in two plies carries 8 t per leg; the same 100 mm in one ply does not, and no amount of care will make it.
• An outer layer that is not the load path. The outer ply meets the hook, the shackle and the edge of the load. The inner plies carry the tension. A scuff that would have been a cut into a single band lands on a layer that is not doing the holding.
• A softer body for the same figure. A narrow multi-ply band rolls and folds more easily than a very wide single layer, which matters at the eye and in a tight choke.
• A visible record of abuse. Because the plies are separate layers, damage shows up at the surface before it reaches the middle. That is a margin for inspection, not a licence to keep lifting.

Specifications

Capacity by Width and Ply

Two numbers set the figure: the width of the band and the number of plies. The table is one leg hanging vertically, which is the figure printed on the sling. Every other arrangement multiplies it by the hitch factor further down.

Üstünde 48 t per leg the sling is built to order. The 5:1 Ve 6:1 builds reach the same working load limit at a narrower width or one ply less; the figure that applies is always the one on the label, so state the factor on the enquiry and it is confirmed on the drawing.

Narrow and Deep, Against Wide and Thin

This is the decision the ply count really makes, and it is worth putting in numbers rather than adjectives. Take the same 8 t per leg:

Neither is better. They are the same tonnage in two shapes, and the shape has to match the load: a narrow multi-ply band where the lift point is tight or the band will be knocked about, a wide band where the surface is what matters. The single-ply figures are published on the single ply eye-eye webbing sling sayfa, so the two can be read side by side.

Impact, Kenarlar, and the Life of the Band

A sling rarely dies of overload. It dies of what happens to it between lifts: the band dropped on a corner, dragged over grit, pinched between the load and the floor, swung into the edge of a steel plate. That is where the ply count pays for itself, and it is worth being precise about how.

• The impact lands on the outside. A blow that nicks or glazes the outer ply has not yet reached the yarn that is carrying the tension. On a single layer, that same blow is a defect in the load path.
• The layers spread the contact. Several sewn layers behave like a slightly padded body: the bearing pressure at an edge is shared and the weave is less likely to be cut through in one contact.
• The stitching stops a tear travelling. The bond between plies interrupts a running rip, which is how a woven band usually fails once it is cut – along the weave, quickly.
• It buys inspection time, not immunity. A multi-ply webbing sling is not cut-proof, and the ply count is no substitute for a sleeve. A sharp edge still needs a protective sleeve, and a damaged outer ply still retires the sling under EN 1492-1 – the extra layer gives you a margin to notice, not a reason to keep going.

Service life follows the same logic. A multi-ply band carries the same load over a thicker cross-section, so each layer works further from its limit, and the outer layer absorbs the abrasion that would otherwise thin the only layer there is. In repetitive duty – a press shop, a precast yard, a port – that difference is measured in replacements per year rather than in tonnage.

Choosing the Build: Four Questions

Hitch Factors: the Label Is One Number

The figure on the sling describes a vertical lift. Everything else is that figure multiplied by the factor for the arrangement, and on a multi-ply sling the choke is the one most often missed – because a thick band takes a choke so readily.

İşaretleme, Length and What Else to Send

Every sling carries its working load limit, uzunluk, mode and date printed into the webbing and repeated on a sewn label – printed into the band rather than onto a tag, so the figure is still legible after a year on site. Length is quoted two ways and both are legitimate: the toplam uzunluk from eye tip to eye tip, ve etkili uzunluk from bearing point to bearing point. State which one you mean; more slings come back for a length misunderstanding than for any other reason.

Yükü gönder, the working load limit per hitch, the arrangement, the width the lift point allows, the fittings the eyes must pass, and the surface the band must not mark. A multi-ply webbing sling is quoted from those six answers, not from a stock list, and the width, kat, the eye reinforcement and the protection come back on a drawing before anything is woven.

Sıkça Sorulan Sorular

What is a multi-ply webbing sling?

İki, three or four layers of high-tenacity polyester webbing stacked and sewn into a single band. Each layer adds to the cross-section that carries the load, so a multi-ply sling reaches a given working load limit at a narrower width than a single-ply sling would need.

Does more plies always mean more capacity?

At the same width, yes – the figures run 8 / 12 / 16 t for 100 mm in 2, 3 Ve 4 kat. What it does not mean is that you can pick a ply count by eye: the working load limit printed on the label, adjusted by the hitch factor, is the only figure that applies to a lift.

Is a multi-ply sling stronger than a wider single-ply one?

Not stronger – the same figure in a different shape. Bir 8 t load can be carried by a 100 mm two-ply band or a 240 mm single-ply band at a 7:1 faktör. The two-ply is narrower and easier in a tight lift point; the single ply spreads the pressure over a wider face. Choose by what the load needs.

Will a multi-ply sling protect itself from being knocked or cut?

It gives you an outer layer that is not carrying the load, so an impact or a scuff shows up on the surface before it reaches the load path, and the sewn plies slow a tear that starts at an edge. That is a margin, not immunity: a sharp edge still needs a sleeve, and a damaged outer ply still retires the sling.

2-kat, 3-ply or 4-ply – which should I order?

Read the width you have room for, then take the ply count that reaches the figure you need. If the figure is already met at 2-ply, order 4-ply only for repetitive duty or rough handling, where the outer layers are doing real work.

What safety factor and elongation does a multi-ply sling have?

7:1 as standard to EN 1492-1, ile 5:1 Ve 6:1 istek üzerine, and elongation of 7 % or less at the working load limit. A different factor is a different article – the same tonnage at 6:1 is narrower – so the factor belongs on the enquiry, not in a footnote.

Can a multi-ply sling be printed with our own reference?

Evet. Çalışma yükü sınırı, the length and your own part or asset number can be printed into the webbing as a production instruction, in the exact string and case you send, alongside the standard marking.

Request a Quotation

Send your multi-ply sling specification for a quotation

Telephone / WeChat: +86 180 6600 2268 | E-posta: 702461526@qq.com
Adres: Lifute Endüstri Parkı, Taizhou Şehri, Jiangsu Eyaleti, Çin | HS kodu: 630790

Related Slings

• Heavy duty eye & eye flat web sling – the multi-ply build with reinforced eyes, kadar 48 T
• Single ply eye-eye webbing sling – the one-layer build, 1-12 T
• Polyester webbing sling – lif, and the single-ply range it starts from
• Geniş vücut kaldırma dokuma sapan – where pressure on the load must be spread further
• Çelik boru kaldırma kayışı – the edge-protection case in detail
• Eye and eye webbing slings – flat or twisted eye, single and multi-ply
• Sonsuz düz dokuma sapan – the same body without eyes
• Yayıcı kirişin kaldırılması – for two and four leg assemblies
• Webbing slings – the full range and the mode factors