లిఫ్ట్ స్లింగ్ రిగ్గింగ్ కంపెనీ ఉత్పత్తి 5 Ton Heavy Duty Ratchet Straps,10 టోన్ రాట్చెట్ స్ట్రాప్,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.
5 Ton Heavy Duty Ratchet Straps
50 mm పాలిస్టర్ వెబ్బింగ్, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 కు 10 m ప్రమాణంగా, LC 2,500 మరియు, STF 350 మరియు N వద్ద 50 మరియు చేతి బలం. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.
Part of the వెబ్బింగ్ స్లింగ్ and lashing range. ది 50 mm specification in isolation sits on the 50 మి.మీ 5000 కేజీ రాట్చెట్ లాషింగ్ బెల్ట్ పేజీ.
What “5 Ton” Actually Means on a Ratchet Strap
Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. EN కింద 12195-2 లాషింగ్ స్ట్రాప్ యొక్క వెబ్బింగ్ దాని కొరడా దెబ్బ సామర్థ్యం కంటే కనీసం రెండు రెట్లు చేరుకోవాలి, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.
| మూర్తి | Value on the 50 mm assembly | అది ఏమి వివరిస్తుంది | How it gets misread |
|---|---|---|---|
| కనిష్ట బ్రేకింగ్ బలం | 5,000 మరియు (5,000 కిలో) | పుల్ టెస్ట్లో అసెంబ్లీ విఫలమయ్యే లోడ్ | Read as the working figure — the mistake that overloads a trailer |
| లాషింగ్ సామర్థ్యం (LC) | 2,500 మరియు (2.5 t) | అసెంబ్లీని నిలుపుదల చేయడానికి రేట్ చేయబడింది, printed on the label | లిఫ్టింగ్ స్లింగ్ యొక్క WLLతో పోలిస్తే, which is a different duty altogether |
| ప్రామాణిక ఉద్రిక్తత శక్తి (STF) | 350 మరియు N వద్ద 50 మరియు చేతి బలం | The tension one person reaches with the ratchet handle | LC తో గందరగోళం, కాబట్టి ఆపరేటర్ ఉపయోగకరమైన పాయింట్ను దాటుకుంటూనే ఉంటాడు |
ఎందుకు 50 mm Build Is the Heavy-Duty Default
Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. ది 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.
| వెబ్ వెడల్పు | Typical LC | బ్రేకింగ్ బలం | దేనికి కొంటారు |
|---|---|---|---|
| 25 మి.మీ (1 లో) | 400–500 daN | 800–1,000 daN | Tool boxes, light restraint, tight anchor eyes |
| 35 మి.మీ (1-3/8 లో) | 750 మరియు | 1,500 మరియు | Van and trailer decks, general cargo |
| 38 మి.మీ (1-1/2 లో) | 1,000–1,500 daN | 2,000–3,000 daN | స్టీల్ ప్లేట్, పైపు కట్టలు, plant |
| 50 మి.మీ (2 లో) | 2,500 మరియు | 5,000 మరియు | Heavy cargo restraint, కాయిల్స్, యంత్రాలు, కంటైనర్లు |
| 75–100 మి.మీ | 5,000 daN and up | 10,000 daN and up | Abnormal loads, where the bed allows the width |
The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.
Standard Specification of the 5 Ton Assembly
| అంశం | స్పెసిఫికేషన్ |
|---|---|
| వెబ్బింగ్ | 100% అధిక దృఢత్వం గల పాలిస్టర్, ట్విల్ నేత, UV స్థిరీకరించబడింది, 50 mm ± 2% |
| బ్యాండ్ మందం / ద్రవ్యరాశి | 1.8 mm నామమాత్రం / 88 g per metre |
| లాషింగ్ సామర్థ్యం (LC) | 2,500 daN per assembly |
| కనిష్ట బ్రేకింగ్ బలం | 5,000 మరియు (2:1 against LC) |
| ప్రామాణిక ఉద్రిక్తత శక్తి (STF) | 350 మరియు N వద్ద 50 మరియు చేతి బలం |
| టెన్షనర్ | Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle |
| LC వద్ద పొడుగు | 7% లేదా తక్కువ |
| సేవ ఉష్ణోగ్రత | −40 °C నుండి +100 °C (పాలిస్టర్ వెబ్బింగ్) |
| ప్రామాణిక పొడవు | 3–10 మీ; 1–30 m to order |
| మార్కింగ్ | నేసిన లేబుల్: LC, STF, పొడవు, బ్యాచ్ సంఖ్య, standard reference |
| ప్రామాణికం | Designed, tested and marked to EN 12195-2 |
| HS కోడ్ | 630790 |
The End Fitting Decides Whether the Strap Fits the Job
The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.
| అమర్చడం | Anchors to | Notes before ordering |
|---|---|---|
| Chassis rave hook | Flatbed side rail, chassis lip | Check rail thickness and that the hook throat clears it |
| Claw hook | Anchor rings, D rings, recessed eyes | Opening must clear the ring; load on the crown only |
| D ring / delta ring | Welded or bolted anchor points | Ring bore at least as wide as the webbing |
| Flat snap hook | ఇ-ట్రాక్, slotted rail, రంధ్రాలు | Confirm slot width; snap gate must close fully |
| S hook | పైపులు, పట్టాలు, frame members | Both ends must seat without point loading on a weld |
| Sewn loop / looped ends | Around the load or through a bore | Nothing metal at the load; ideal for finished surfaces |
| అంతులేని, అమర్చడం లేదు | Girth only — hulls, కాయిల్స్, కట్టలు | See the endless loop build below |

ది 5 Ton Strap in Two Special Builds
Polyester covers most freight, and it fails predictably when it is out of its depth: అది చుట్టూ మెత్తగా ఉంటుంది 150 °C and melts at about 255 °C, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.
Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces
The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 లేదా 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 మరియు N వద్ద 25 mm నుండి 2,500 మరియు N వద్ద 50 మి.మీ, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.
The grade decision is about chloride, లోడ్ కాదు. 304 (1.4301) handles rain, మంచినీరు, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 అది బలమైనదని నమ్మకంతో తప్పు ఆస్తికి చెల్లిస్తున్నాడు. Where the application is safety-related, confirm the grade on the mill certificate rather than on the invoice description.
Two shop-floor notes worth passing on. Stainless threads gall, so a dry 316 nut run hard onto a 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. And stainless bolted to aluminium in salt water forms a galvanic pair, so where the strap anchors to an alloy frame, isolate the contact.
Full range and grade comparison: అంతులేని స్టెయిన్లెస్ స్టీల్ రాట్చెట్ పట్టీ.
అరామిడ్ (కెవ్లర్) ratchet straps — for heat, sparks and cut edges
Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 °C. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.
The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.
Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.
How Many Straps Does the Load Actually Need?
Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.
| Straps used | Angle to the deck | Restraint per strap | Total restraint |
|---|---|---|---|
| 2 | 45° | సుమారు. 1,750 మరియు | సుమారు. 3,500 మరియు |
| 4 | 30° | సుమారు. 1,250 మరియు | సుమారు. 5,000 మరియు |
| 4 | 45° | సుమారు. 1,750 మరియు | సుమారు. 7,000 మరియు |
| 4 | 60° | సుమారు. 2,165 మరియు | సుమారు. 8,660 మరియు |
| 6 | 45° | సుమారు. 1,750 మరియు | సుమారు. 10,500 మరియు |
The arithmetic is an illustration, not a lashing plan: IN 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.
ఎక్కడ 5 Ton Ratchet Strap Earns Its Keep
- ఫ్లాట్బెడ్, container and plant trailer restraint — the volume application for the 50 mm build.
- స్టీల్ కాయిల్, పలక, billet and pipe bundles, with edge protection at the contact points.
- యంత్రాలు, moulds and skid-mounted plant, ఎక్కడ a 25 mm strap has neither the width nor the tension.
- కలప ప్యాకెట్లు, డబ్బాలు మరియు స్టిలేజ్లు, including the endless form that simply closes round the pack.
- Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
- మెరైన్, marina and wash-down duty in 304 లేదా 316 where plated hardware would be a maintenance item.
- Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.

రంగు, Printing and Private Label
Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, నారింజ, పసుపు, నలుపు, ఎరుపు, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, పొడవు, standard and traceability code. Cartons of 10 కు 20 ముక్కలు, palletised for export, with neutral or own-brand packaging as required.
పరీక్షిస్తోంది, Traceability and the Paperwork Buyers Ask For
Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. Test reports, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.
One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.
తరచుగా అడిగే ప్రశ్నలు
ఒక 5 ton ratchet strap rated to lift 5 టన్నులు?
నం, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.
Why does the same strap get called 5 టన్ను మరియు 2.5 టన్ను?
Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.
50 mm లేదా 38 mm for a flatbed?
50 మి.మీ, unless the anchor points are small. ది 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; ది 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.
Do I need 304 లేదా 316 స్టెయిన్లెస్?
316 where chloride is present — sea air, ఉప్పు స్ప్రే, డి-ఐసింగ్ ఉప్పు, boatyards, ఆహార మొక్కలు. 304 is enough for rain, మంచినీరు, condensation and indoor wash-down. The difference is corrosion resistance, బలం కాదు.
At what temperature does polyester fail, and what does aramid do instead?
Polyester softens around 150 °C and melts at about 255 °C, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 °C, and chars at about 427 కరిగే బదులు °C. పైన 400 °C, or against molten metal, both need a heat shield.
Can the strap be supplied with a printed brand and a custom length?
అవును. వెడల్పులు, వరకు పొడవు 30 m, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.
కొటేషన్ను అభ్యర్థించండి
Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, పర్యావరణం (salt, వేడి, వాష్-డౌన్), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.
లిఫ్ట్ స్లింగ్ రిగ్గింగ్ కంపెనీ
లిఫ్యూట్ ఇండస్ట్రియల్ పార్క్, తైజౌ సిటీ, జియాంగ్సు ప్రావిన్స్, చైనా
Tel: +86 523 8693 5818 · WhatsApp: +86 180 6600 2268
ఇ-మెయిల్: 702461526@qq.com · HS code 630790
సంబంధిత ఉత్పత్తులు
- Ratchet straps — the full lashing range, 25 mm నుండి 100 మి.మీ.
- 50 మి.మీ 5000 కేజీ రాట్చెట్ లాషింగ్ బెల్ట్ — this specification in detail.
- Endless loop ratchet strap — closed loop, హుక్ లేదు, for girth-only loads.
- Endless stainless steel ratchet strap — 304 లేదా 316 for salt and wash-down.
- Aramid flame retardant ratchet straps — 200 °C నిరంతర, 400 °C గరిష్టం.
- పాలిస్టర్ వెబ్బింగ్ స్లింగ్ — when the job is lifting rather than lashing.

