தயாரிப்பு வகைகள்

Multi-ply webbing sling

சுருக்கமான விளக்கம்:

Lift sling rigging company produce Multi-ply webbing sling,duplex webbing sling,duplex endless webbing sling,multi-ply endless flat web sling,Multi-ply endless webbing sling,Flat Multiply Webbing Sling.

Multi-ply webbing sling in 2, 3 மற்றும் 4 ply polyester: 100-300 mm web, 8-100 t per leg at 7:1. The outer ply takes the knocks, the inner plies carry the load.

தயாரிப்பு விவரம்

Lift sling rigging company produce Multi-ply webbing sling,duplex webbing sling,duplex endless webbing sling,multi-ply endless flat web sling,Multi-ply endless webbing sling,Flat Multiply Webbing Sling,Multi – Ply Lifting Sling,Multi-Layer Weaving Lift Sling Strap,Multi-ply polyester web sling.

Multi-ply Webbing Sling

A multi-ply webbing sling is two, three or four layers of high-tenacity polyester webbing sewn into one load-bearing band. The plies are stacked and stitched through, so the cross-section that carries the load is the width multiplied by the number of plies – which is why a multi-ply sling reaches in 100 மிமீ what a single layer needs 240 மிமீ to reach. Standard build: 2, 3 அல்லது 4 ஓடு, 100-300 மிமீ wide, 8 டி செய்ய 48 டி per leg in the vertical mode at a 7:1 காரணி, elongation of 7 % or less வேலை சுமை வரம்பில், rated to IN 1492-1 and made to order in any length from 1 மீ முதல் 100 மீ.

Multi-ply webbing sling in orange polyester, showing the layered edge of the flat band
Look at the cut edge: several layers of webbing, not one. That stack is the whole argument for this product.

What “Multi-Ply” Actually Adds

Capacity in a flat sling is set by the cross-section of load-bearing yarn, and the cross-section is width x plies. There are only two ways to buy a figure: go wider, or go deeper. Going deeper is what this page is about.

  • More capacity in the same width. ஏ 100 mm band in two plies carries 8 ஒரு காலுக்கு டி; the same 100 mm in one ply does not, and no amount of care will make it.
  • An outer layer that is not the load path. The outer ply meets the hook, the shackle and the edge of the load. The inner plies carry the tension. A scuff that would have been a cut into a single band lands on a layer that is not doing the holding.
  • A softer body for the same figure. A narrow multi-ply band rolls and folds more easily than a very wide single layer, which matters at the eye and in a tight choke.
  • A visible record of abuse. Because the plies are separate layers, damage shows up at the surface before it reaches the middle. That is a margin for inspection, not a licence to keep lifting.

விவரக்குறிப்புகள்

Standard multi-ply range
அளவுரு விருப்பங்கள்
தயாரிப்பு Multi-ply webbing sling / இரட்டை, triplex or quadplex flat web sling
Build 2-ஓடு (இரட்டை) · 3-ply (triplex) · 4-ply (quadplex); single ply on request
Fibre 100 % உயர் உறுதியான பாலியஸ்டர் (PET); கோரிக்கையின் பேரில் நைலான் வெப்பிங்
வலைப்பின்னல் அகலம் 100 / 150 / 200 / 240 / 300 mm in the multi-ply range (25-300 mm across the full range)
வலைப்பின்னல் தடிமன் 1.8 மிமீ – 6.0 மிமீ, depending on width and ply
வேலை சுமை வரம்பு 8 டி – 48 ஒரு காலுக்கு டி, vertical mode
பாதுகாப்பு காரணி 7:1 standard to EN 1492-1; 5:1 மற்றும் 6:1 கோரிக்கையின் பேரில்
WLL இல் நீட்டிப்பு 7 % or less
End form Eye and eye (flat or twisted eye), or endless flat; eye length 150-1500 மிமீ
நீளம் 1 மீ – 100 மீ, ஆர்டர் செய்ய செய்யப்பட்டது; overall length and effective length both quoted
வேலை வெப்பநிலை -40 °C முதல் +100 °C
Colour and marking IN 1492-1 colour by working load limit, அல்லது தனிப்பயன் நிறம்; WLL, நீளம், mode and date printed into the webbing
HS குறியீடு 630790

Capacity by Width and Ply

Two numbers set the figure: the width of the band and the number of plies. The table is one leg hanging vertically, கவண் மீது அச்சிடப்பட்ட உருவம். Every other arrangement multiplies it by the hitch factor further down.

Working load limit per leg, vertical mode, 7:1
வலைப்பின்னல் அகலம் 2-ஓடு 3-ஓடு 4-ஓடு வழக்கமான கடமை
100 மிமீ 8 டி 12 டி 16 டி எஃகு அலகுகள், கான்கிரீட் கூறுகள், இயந்திர பாகங்கள்
150 மிமீ 12 டி 18 டி 24 டி Long fabrications, குழாய் மற்றும் குழாய் மூட்டைகள்
200 மிமீ 16 டி 24 டி 32 டி கனரக புனையப்பட்ட எஃகு, வார்ப்புகள், moulds
240 மிமீ 20 டி 30 டி 40 டி Large weldments, கப்பல் கட்டும் தளம் மற்றும் துறைமுக கடமை
300 மிமீ 24 டி 36 டி 48 டி Heaviest standard range, கனமான ஆலை

மேலே 48 t per leg the sling is built to order. தி 5:1 மற்றும் 6:1 builds reach the same working load limit at a narrower width or one ply less; the figure that applies is always the one on the label, so state the factor on the enquiry and it is confirmed on the drawing.

Narrow and Deep, Against Wide and Thin

This is the decision the ply count really makes, and it is worth putting in numbers rather than adjectives. Take the same 8 ஒரு காலுக்கு டி:

Two ways to reach 8 t per leg at 7:1
Build அகலம் What you gain What you pay
2-ply multi-ply 100 மிமீ Narrow band: fits a tight choke, a small eye, a confined lift point; less bulk at the shackle Higher bearing pressure on the load – a soft or finished surface is marked sooner than under a wide band
ஒற்றை அடுக்கு 240 மிமீ Wide contact: pressure spread over more of the surface, gentler on soft and coated loads A stiff, bulky band; a large eye; awkward where the lift point is narrow

Neither is better. They are the same tonnage in two shapes, and the shape has to match the load: a narrow multi-ply band where the lift point is tight or the band will be knocked about, a wide band where the surface is what matters. The single-ply figures are published on the single ply eye-eye webbing sling பக்கம், so the two can be read side by side.

Multi-ply polyester webbing sling coiled on a granite floor, printed working load limit visible on the band
The band is thick enough to hold its own curve – a four-ply body does not collapse into a flat ribbon when it is laid down.

Impact, விளிம்புகள், and the Life of the Band

A sling rarely dies of overload. It dies of what happens to it between lifts: the band dropped on a corner, dragged over grit, pinched between the load and the floor, swung into the edge of a steel plate. That is where the ply count pays for itself, and it is worth being precise about how.

  • The impact lands on the outside. A blow that nicks or glazes the outer ply has not yet reached the yarn that is carrying the tension. On a single layer, that same blow is a defect in the load path.
  • The layers spread the contact. Several sewn layers behave like a slightly padded body: the bearing pressure at an edge is shared and the weave is less likely to be cut through in one contact.
  • The stitching stops a tear travelling. The bond between plies interrupts a running rip, which is how a woven band usually fails once it is cut – along the weave, quickly.
  • It buys inspection time, not immunity. A multi-ply webbing sling is not cut-proof, and the ply count is no substitute for a sleeve. A sharp edge still needs a protective sleeve, and a damaged outer ply still retires the sling under EN 1492-1 – the extra layer gives you a margin to notice, not a reason to keep going.
Yellow multi-ply webbing sling with protective sleeves at the eyes, laid out on a white background
Sleeves at the eyes and a layered body: the two things that keep a multi-ply sling in service through repetitive handling.

Service life follows the same logic. A multi-ply band carries the same load over a thicker cross-section, so each layer works further from its limit, and the outer layer absorbs the abrasion that would otherwise thin the only layer there is. In repetitive duty – a press shop, a precast yard, a port – that difference is measured in replacements per year rather than in tonnage.

Choosing the Build: Four Questions

Selection path
Step Question What it settles
1 What is the working load per leg, in the hitch you will really use? The figure to buy. ஏ 20 டி ஒரு சோக்கில் ஏற்ற வேண்டும் a 24 t band (20 / 0.8), not a 20 t one
2 How wide can the band be at the lift point? Whether the capacity is bought with width or with plies
3 What does the band meet – finished surface, raw edge, கிரிட், வெப்பம்? ஸ்லீவ், wear pad, or a different fibre altogether
4 How often, and by whom? Ply count. Repetitive duty with rough handling justifies 4-ply; occasional clean lifts do not

Hitch Factors: the Label Is One Number

The figure on the sling describes a vertical lift. Everything else is that figure multiplied by the factor for the arrangement, and on a multi-ply sling the choke is the one most often missed – because a thick band takes a choke so readily.

Mode factors to EN 1492-1
பயன்முறை காரணி ஏ 16 t 4-ply sling gives
செங்குத்து 1.0 16 டி
மூச்சு திணறியது 0.8 12.8 டி
கூடை, 0-45° 2.0 32 டி
கூடை, 45-60° 1.4 22.4 டி
இரண்டு கால்கள், 0-45° 1.4 per assembly
இரண்டு கால்கள், 45-60° 1.0 per assembly

குறியிடுதல், Length and What Else to Send

Every sling carries its working load limit, நீளம், mode and date printed into the webbing and repeated on a sewn label – printed into the band rather than onto a tag, so the figure is still legible after a year on site. Length is quoted two ways and both are legitimate: தி மொத்த நீளம் from eye tip to eye tip, மற்றும் தி பயனுள்ள நீளம் from bearing point to bearing point. State which one you mean; more slings come back for a length misunderstanding than for any other reason.

சுமை அனுப்பவும், the working load limit per hitch, ஏற்பாடு, the width the lift point allows, the fittings the eyes must pass, and the surface the band must not mark. A multi-ply webbing sling is quoted from those six answers, not from a stock list, and the width, the ply, the eye reinforcement and the protection come back on a drawing before anything is woven.

அடிக்கடி கேட்கப்படும் கேள்விகள்

What is a multi-ply webbing sling?

Two, three or four layers of high-tenacity polyester webbing stacked and sewn into a single band. Each layer adds to the cross-section that carries the load, so a multi-ply sling reaches a given working load limit at a narrower width than a single-ply sling would need.

Does more plies always mean more capacity?

At the same width, ஆம் – the figures run 8 / 12 / 16 t for 100 mm in 2, 3 மற்றும் 4 ஓடு. What it does not mean is that you can pick a ply count by eye: the working load limit printed on the label, adjusted by the hitch factor, is the only figure that applies to a lift.

Is a multi-ply sling stronger than a wider single-ply one?

Not stronger – the same figure in a different shape. அன் 8 t load can be carried by a 100 mm two-ply band or a 240 mm single-ply band at a 7:1 காரணி. The two-ply is narrower and easier in a tight lift point; the single ply spreads the pressure over a wider face. Choose by what the load needs.

Will a multi-ply sling protect itself from being knocked or cut?

It gives you an outer layer that is not carrying the load, so an impact or a scuff shows up on the surface before it reaches the load path, and the sewn plies slow a tear that starts at an edge. That is a margin, not immunity: a sharp edge still needs a sleeve, and a damaged outer ply still retires the sling.

2-ஓடு, 3-ply or 4-ply – which should I order?

Read the width you have room for, then take the ply count that reaches the figure you need. If the figure is already met at 2-ply, order 4-ply only for repetitive duty or rough handling, where the outer layers are doing real work.

What safety factor and elongation does a multi-ply sling have?

7:1 as standard to EN 1492-1, with 5:1 மற்றும் 6:1 கோரிக்கையின் பேரில், and elongation of 7 % or less at the working load limit. A different factor is a different article – the same tonnage at 6:1 is narrower – so the factor belongs on the enquiry, not in a footnote.

Can a multi-ply sling be printed with our own reference?

ஆம். வேலை சுமை வரம்பு, the length and your own part or asset number can be printed into the webbing as a production instruction, in the exact string and case you send, alongside the standard marking.

ஒரு மேற்கோளைக் கோரவும்

Send your multi-ply sling specification for a quotation

தொலைபேசி / WeChat: +86 180 6600 2268 | மின்னஞ்சல்: 702461526@qq.com
முகவரி: லிஃப்யூட் தொழில்துறை பூங்கா, தைஜோ நகரம், ஜியாங்சு மாகாணம், சீனா | HS குறியீடு: 630790

Related Slings

உங்கள் செய்தியை விடுங்கள்

மேலே உருட்டவும்