Produktkategorier

Single Ply Endless Lifting Sling

Kort beskrivning:

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Single ply endless lifting sling: one layer, one lapped joint, inga slutar. 4 mm band, 1-12 t kl 7:1 två EN 1492-1, quoted by circumference or flat length.

Produktdetaljer

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Endless lifting sling · single layer · 4 mm flat band

Single Ply Endless Lifting Sling

Ett lager, one lapped joint, inga slutar. The lightest closed loop in the range: it folds into a pocket, turns a tight radius and drapes over the load — 1 t till 12 t kl 7:1 två EN 1492-1.

1–12 t single ply ladder 4 mm band section 7:1 två EN 1492-1 25–300 mm bandbredd
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets

A single ply endless lifting sling is the single-layer build of the closed loop: one band of high-tenacity polyester, lapped over itself and closed with dense parallel rows of stitching, utan ögon, no fittings and no metal anywhere on the article. Det är den ändlösa vävslingan av typ A av EN 1492-1 — the type 5 web sling in North American usage.

The word to be careful with is ply. It does not mean two slings or two bands in parallel; it means how many layers of webbing are woven into the one band the loop is made from. Single ply is one layer, and everything that follows — the 4 mm section, the weight per metre, the way it turns round a small radius, and the capacity it can be given at a given width — comes from that one decision.

The trade-off in one line. Single ply gives the most flexible loop and the lowest weight per metre; duplex gives more capacity at the same width, a stiffer bearing face and more abrasion reserve. Nedan ca 6 t, and wherever the loop has to fold, single ply is the right default.

What one layer actually gives you

Four practical differences separate the single-layer loop from the duplex build, and each one shows up on a different job:

  • A 4 mm section. The band folds into a pocket, coils onto a hook and passes between a load and a tight gap where a thicker band will not go.
  • Less weight per metre. The ladder below runs from 0.20 kg/m vid 1 t till 2.05 kg/m vid 10 t — a one-handed carry for the sizes most yards actually use.
  • More supple over a radius. One layer conforms to pipe, tube and rolled sections instead of standing off them, so contact is over the full width rather than at two edges.
  • En led, thin and easy to read. The lapped joint is the only made connection in the load path; in a single layer the stitching rows sit on one visible face, with no second layer masking them.
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets
Plate and sheet in a basket: one layer of band, doubled under the load, a full-width soft bearing face and no fitting anywhere near the steel.

Single ply against duplex, at the same width

The two builds are not two grades of the same thing; they are two answers to different questions. The comparison below is the one we use in quotation, and the widths are the published single-ply ladder.

Tabell 1 — Single ply and duplex, same nominal width
Enkelt lager Duplex
Layers in the band En Två, woven as one band
Section thickness 4 mm at the standard ladder Roughly twice the single-ply section
Capacity at a given width The ladder figure Higher — the reason duplex exists above the single-ply range
Vikt per meter 0.20 kg/m vid 1 t till 2.05 kg/m vid 10 t Higher for the same width
Hantering Folds small, turns a tight radius, drapes onto the load Styvare; sits flatter over an edge and resists abrasion longer
Där den vinner Nedan ca 6 t, tight gaps, små diametrar, mixed rigs High capacity in a narrow width, rough edges, heavy abrasion
Gemensam One lap, stitching visible on the face One lap through the doubled band

The duplex build has its own page: double ply endless lifting sling.

The capacity ladder, enkelskikt

Working load limits are quoted in straight lift, på 7:1 två EN 1492-1. Colour follows EN 1492-1 and is a capacity band, not a material; ovan 10 t there is no colour code and the label is the only rating.

Tabell 2 — Single ply endless sling: kapacitet, colour and weight
WLL, rak lyft Färg Referensbredd Längdintervall Ca. vikt Kvävd (× 0.8)
1 t Violett Bekräfta vid beställning 0.5 – 100 m 0.22 kg/m 0.8 t
2 t Grön 50 mm 1 – 100 m 0.35 kg/m 1.6 t
3 t Gul 75 mm 1 – 100 m 0.52 kg/m 2.4 t
4 t Grå 100 mm 1.5 – 100 m 0.80 kg/m 3.2 t
5 t Röd 125 mm 1.5 – 100 m 0.85 kg/m 4.0 t
6 t Brun 150 mm 1.5 – 100 m 0.96 kg/m 4.8 t
8 t Blå 200 mm 2 – 100 m 1.34 kg/m 6.4 t
10 t Orange 250 mm 2 – 100 m 1.64 kg/m 8.0 t
Ovan 10 t Ingen färgkod Duplex build Att beställa På begäran Etiketten styr

Widths and weights are the published series for this range; the finished width, ply and weight are confirmed on the order acknowledgement.

Bredd, safety factor and the same capacity

A higher safety factor needs a wider band for the same working load limit, which is why the width column has three values. Tell us the standard your site works to and the sling is built to it; the figures below are the single-ply polyester ladder.

Tabell 3 — Band width by safety factor, 4 mm single ply polyester
WLL På 5:1 På 6:1 På 7:1 Tjocklek Vikt kl 7:1
1 t (1 000 kg) 25 mm 25 mm 30 mm 4 mm 0.20 kg/m
2 t (2 000 kg) 50 mm 50 mm 60 mm 4 mm 0.60 kg/m
3 t (3 000 kg) 75 mm 75 mm 90 mm 4 mm 0.78 kg/m
4 t (4 000 kg) 100 mm 100 mm 120 mm 4 mm 0.90 kg/m
5 t (5 000 kg) 125 mm 125 mm 150 mm 4 mm 1.14 kg/m
6 t (6 000 kg) 150 mm 150 mm 180 mm 4 mm 1.33 kg/m
8 t (8 000 kg) 200 mm 200 mm 240 mm 4 mm 1.85 kg/m
10 t (10 000 kg) 250 mm 250 mm 300 mm 4 mm 2.05 kg/m
12 t (12 000 kg) 300 mm 300 mm 300 mm 4 mm 2.70 kg/m
Four single ply endless slings in white, violett, green and black
The capacity colour is woven in, not printed on: white for the general band, violet for 1 t, green for 2 t, with one black transverse stripe per tonne as a second check.

Leden, and why it is the first thing to look at

En ändlös sele är oändlig i användning, inte sömlös. Bandet lappas över sig själv och stängs med täta parallella rader av sömmar; det varvet är en fullstyrka led och den sitter i lastbanan. Det är den enda kopplingen i hela artikeln.

On a single-layer loop that joint is easier to inspect than on a duplex one, because the stitching rows lie on one visible face rather than between two layers. Look for broken or pulled stitches, a lap that has started to open, and abrasion where the lap passes over an edge. If the joint is sound, the rest of the loop is one continuous band and can be read anywhere along its length.

White single ply endless sling laid out on gravel
Ett band, lapped and stitched once. That single joint is the only made connection in the load path, and the first thing an inspector reads.

Three hitches from the same loop

The marked figure is the straight-lift rating; every other arrangement is derived from it. Size the sling to the hitch the crew will actually rig, not to the one in the lift plan.

Tabell 4 — Mode factor by hitch
Lifta Lägesfaktor Vad det betyder på plats
Vertikal × 1.0 The label figure applies directly
Kvävd × 0.8 A 4 t last i en choke behöver en 5 t sling — the wrap grips as the load comes on
Korg, ben nära vertikala × 2.0 Both sides of the loop carry the load and the bearing face is doubled
Korg, 7°–45° × 1.4 As the legs open the rating falls; plan the angle, not only the weight
Korg, 45°–60° × 1.0 At wide angles the basket advantage is gone — treat it as a straight lift

Längd: omkrets, or the height you actually get

En sluten slinga har inga ändar, så det finns inget att mäta från början. This trade quotes the same sling two ways, och de skiljer sig med ungefär en faktor två: the circumference is the perimeter of the loop, while the effective working length is the usable height you get, roughly half the circumference because the loop is doubled when it hangs.

Tabell 5 — The same sling under both conventions
Citerat som Vad den mäter Samma sele är lika
Omkrets The perimeter of the loop — total band in the article 2 m
Effektiv arbetslängd Den användbara höjden; the loop doubles when it hangs 1 m

Namnge konventionen med figuren, eller ange användningen istället — artikelns omkrets ska öglan gå runt — och otydligheten försvinner innan bandet skärs av.

Green single ply endless sling with its blue capacity label
Den sydda etiketten bär arbetsbelastningsgränsen, materialet, standarden, the length and the batch — on a closed loop it is the whole record of the article.

Polyester, and the limits of it

The standard build is 100% höghållfast polyester (PES). It elongates no more than 3% at the working load limit and no more than 10% vid brottlasten, so the load does not creep down as the lift comes on, and the standard build works from −40 °C to +100 °C. Nylon is offered where shock and abrasion dominate; polypropylene where weight and cost matter more than strength; UHMWPE and aramid where strength-to-weight or heat is the deciding factor.

What ends a polyester build is the same list as for any synthetic sling: heat above the range, strong alkalis, sharp edges that cut rather than abrade, and a cut or a glaze anywhere on the circumference. On a closed loop there is no second end to compare, so condition is judged against the surrounding band.

Single ply endless slings lifting bundles of steel pipe at a loading bay
Pipe bundles at a loading bay: the loop is passed round the bundle and both sides come back to the hook, so the band is doubled where the load is heaviest.

Marking and traceability

  • I 1492-1 capacity colour in the weave — violet 1 t, grön 2 t, gul 3 t, grå 4 t, röd 5 t, brun 6 t, blå 8 t, orange 10 t.
  • One black transverse stripe per tonne as a second, optisk kontroll av själva bandet.
  • A sewn label with the working load limit, material, standard, length and traceability code — and above 10 t, the label is the only rating there is.
  • Every sling proof tested in our own laboratory before dispatch, with a test certificate per batch on request; HS-kod 630790.
Two single ply yellow endless slings showing the flat band and its thin section
The single-layer section is 4 mm: it folds into a pocket, turns round a small diameter and drapes over the load instead of standing off it.

Vanliga frågor

What does single ply mean, exactly?

One layer of webbing in the band the loop is made from — not two slings, and not two bands side by side. It gives a 4 mm section at the standard ladder widths, the lowest weight per metre in the range, and the most supple loop we build.

Är en ändlös sele sömlös?

Inga. Den är oändlig i användning, inte sömlös: bandet lappas över sig själv och stängs med täta parallellsömmar, and that lap is a full-strength joint in the load path. What a closed loop removes is the eyes and the end fittings, not the joint. If you need a closed loop with no joint in the load-bearing element at all, det är den ändlös rund sele, where the core is continuous.

How far up the capacity range does single ply go?

The single-ply ladder is published to 12 t kl 7:1 in a 300 mm band; the range as a whole runs to 30 t, and above the single-ply ladder the duplex build is the answer rather than a wider single band.

Can I use one loop for a vertical lift and a choke?

Ja, and the figure changes with the arrangement: 1.0 vertikal, 0.8 kvävdes, 2.0 in a basket with the legs near vertical, faller till 1.4 and then 1.0 as the legs open. Size to the hitch the crew will actually rig.

Will a single ply sling mark aluminium or painted steel?

Bandet är av syntetfiber och ingen passform vidrör belastningen, så det kommer inte att repa eller gradera som en kedja eller en stållina kan. Width is the protection measure — for mirror-finish or anodised work, specify a width above the capacity ladder and the pressure on the surface falls with it.

How should the length be quoted?

Genom omkrets eller genom effektiv arbetslängd - de två skiljer sig med ungefär en faktor två. Namnge konventionen, or give the girth of the article the loop must go round, and the figure is confirmed on the order acknowledgement.

Begär offert

Five things settle a single ply loop

The load — what it is, its girth at the pick positions, and its surface;

The hitch — vertical, kvävd eller korg, and the leg angle if it is a basket;

The working load limit in that hitch, och säkerhetsfaktorn som din webbplats fungerar efter;

The length — with its convention, or the girth the loop has to go round;

The marking and packing — own-brand label, carton or pallet specification.

Send the duty and the figure for a quotation →

Vart ska man gå härnäst

Liftsling Rigging Company · Lifute Industrial Park, Taizhou stad, Jiangsu-provinsen, Kina · HS-kod 630790
Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Lämna ditt meddelande

Bläddra till toppen