Kategórie produktov

Heavy Duty 20 Ton Polyester Cargo Lifting Net

Krátky popis:

Zdvíhacie popruhy vyrába spoločnosť Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

20 t polyester cargo lifting net: 7:1 bezpečnostný faktor, 100 mm duplex bands, four or eight points, cut to the load footprint and proof tested per net.

Detail produktu

Zdvíhacie popruhy vyrába spoločnosť Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

Cargo lifting net · polyester · 20 t trieda

Heavy Duty 20 Ton Polyester Cargo Lifting Net

A 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

20 t limit pracovného zaťaženia 140 t minimum breaking load 100 mm duplexné pásmo 8 zdvíhacie body
Heavy duty polyester flat webbing cargo lifting net laid out, wide bands in a square mesh

A heavy duty 20 ton polyester cargo lifting net is a flat lattice of wide high-tenacity polyester bands, stitched into a square mesh with a doubled border and four or eight reinforced lifting points. The load sits inside the mesh and is carried across the full width of every band beneath it, so the pressure on the cargo is spread over a face rather than concentrated on four sling legs.

We build these nets to order in Taizhou: band width and layer, pletivo, čistá veľkosť, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.

The number behind “20 ton”. The working load limit is 20 t and the safety factor is 7:1, so the net’s minimum breaking load is 140 t. That figure is what the test bed proves; a 20 t is what you are allowed to lift, in the arrangement the net was rated in.

Why polyester at this rating

o 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.

Tabuľka 1 — Polyester against nylon for a 20 t net
Polyester (PET) Nylon (PA)
Stretch under a steady load Low — the net stays square and the load stays level Markedly higher; the net settles and the load can tilt
Absorpcia nárazov Mierne Best in the family; 18–22 % predĺženie pri pretrhnutí
Absorpcia vody Veľmi nízka, dries quickly O 4 %, with some strength loss when saturated
Repetitive crane cycles The usual choice Better where pickups are rough
Pracovná teplota -40 °C až +100 °C Lower at the top end
Best fit for a 20 t zaťaženie Vrecované, paletizované, bundled or stacked cargo lifted on a cycle Irregular or shocky loads that must settle into the mesh
Nylon rope cargo net for comparison with a flat webbing net
The rope alternative: better on irregular loads, but it stretches far more than a polyester band net under a steady 20 t.

What changes when the rating goes to 20 t

Capacity is not a property of the net’s size. It comes from four things moving together: the band, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.

Tabuľka 2 — Build steps from a light net to a 20 t net
Load band Band and build Sieťovina Zdvíhacie body What else changes
2 – 5 t 50 mm single layer 100 mm 4 rohy Standard warehouse net
5 – 10 t 50 – 75 mm, duplex on the load run 100 mm 4 rohy, 8 NA ZNAMENIE Heavier border, reinforced loops
10 – 20 t 75 – 100 mm duplex 100 – 150 mm 8 points Master ring or spreader beam; net built to drawing
20 – 30 t 100 mm duplex, band count from the load face 150 mm 8 points Spreader beam in the assembly; proof test per net
Vyššie 30 t 100 mm multi-layer or wider pitch 150 – 200 mm 8 points or more Engineered and tested to the lift, not to a catalogue

Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.

Z toho vyplývajú dva dôsledky. Po prvé, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 t na a 10 t ring is a 10 t montáž. Po druhé, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Corner detail of a heavy duty webbing cargo net, folded double-stitched border and reinforced loop
Detail rohu: the doubled border is spliced into the loop, which is where the whole 20 t passes through — and where a net is inspected first.

Sizing the net to a 20 t zaťaženie

A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.

  • Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. A 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
  • Forma tašky: the flat width has to wrap up the sides and close over the top, tak flat width = footprint + 2 × bag depth. A 1.2 m footprint in a 0.6 m deep bag needs about 2.4 m across.
  • Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.
Flat polyester cargo lifting net spread on the floor with four corner lifting loops
Flat form: the net overhangs the load footprint and the four corners gather on the hook, so the cargo sits inside the lattice rather than on top of it.

Sieťovina: dimenzované z nákladu, nie tonáž

Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.

Tabuľka 3 — Mesh against the smallest piece in the load
Najmenší rozmer nákladu Typical cargo at 20 t Sieťovina podľa špecifikácie
Pod 75 mm Malé odliatky, komponenty vo veľkom, drummed goods 100 mm diamant, alebo uzavretá sieťka na tašky
75 – 150 mm Tehly, vrecovaný tovar, štiepaný kameň 100 – 150 mm
150 – 250 mm Sawn packs, bundled tube, kartóny, šrot 150 – 200 mm
Koniec 250 mm Bloky, veľký kameň, demolačné sutiny 200 – 300 mm

Špecifikácia

Tabuľka 4 — Heavy duty 20 ton polyester cargo lifting net
Parameter Špecifikácia
Typ Open flat webbing lattice, štyri alebo osem zdvíhacích bodov
Pásový materiál 100 % vysokopevnostný polyester (PET); nylon or UHMWPE on request
Šírka pásma 75 – 100 mm for this class
Band build Duplex (dvojitá vrstva) on the load-bearing run, single layer elsewhere
Otvor zo sieťoviny 100 – 150 mm; square standard, diamond on request
Čistá veľkosť Typicky 4.0 × 4.0 m do 6.0 × 6.0 m, or to the load footprint
Limit pracovného zaťaženia 20,000 kg in the rated arrangement
Bezpečnostný faktor 7:1 — minimum breaking load 140,000 kg
Okraj a rohy Doubled border, spliced into the corners; reinforced loops, four or eight
Kovanie Master ring or grade 80 okovy; spreader beam for eight-point lifts
Liečba UV stabilizovaný, proti starnutiu, abrasion-resistant finish
Pracovná teplota -40 °C až +100 °C
Označovanie WLL, arrangement, net size and identification on a sewn label; band printing on request
Dokumentácia Capacity label, protokol o skúške materiálu, označenie CE; tested on our own 1000 t bed
HS kód 630790
Polyester webbing cargo net with the border and lifting loops visible across its width
Border and loops: the perimeter takes the load from corner to corner, so no single stitch line carries the lift.

Eight points, nie štyri, once the load is long

Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.

  • Four points suit square, compact loads where the net is only holding the cargo together;
  • Eight points suit long or wide loads, and any lift where the net must stay flat under load;
  • The spreader or master link, the slings above it and the hook must each be rated at least 20 t;
  • Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.

The leg sees more than the share: pri 45 deg from the vertical, a 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.

Kontrola a odchod do dôchodku

Tabuľka 5 — What ends a net’s service life
Skontrolujte Odíďte alebo opravte, ak
Corner loops and their stitching A loop is deformed, the stitching is broken, or the band is cut at the throat
Hranica Hranica je prerezaná, flattened, or has pulled out of a corner
Load-bearing bands Any band is cut, hlboko obrúsený, heat glazed or chemically stained
Mesh geometry The lattice is distorted from an overload — the net no longer sits square
Zošívanie Stitch lines are broken or pulled at a crossover
Label and printing The WLL or the arrangement is illegible — an unlabelled net cannot be rated

Inspect before each lift and have the net examined by a competent person at the interval your site sets. Skladujte ho čistý a suchý, mimo zeme a mimo priameho slnka; never knot, weld or heat-repair a webbing net.

Steel coils loaded inside a webbing cargo net on a factory floor
Coils inside the mesh: at this rating the net is as much a handling tool as a container, and the crane never touches the cargo.

Ako je postavená, and how the rating is proven

  • Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
  • Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
  • Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
  • Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.

Rovnaká práca tká popruhy a lisuje objímky oceľových lán, which is why a net, a popruhový popruh a a záves z drôteného lana on the same lift can be matched in rating rather than bought from three suppliers.

Kde a 20 t net does the work

Tabuľka 6 — Sectors that buy this class
Sektor Čo sieť zdvihne Bežná konštrukcia
Oceľ a výroba Balíky, oddielov, záťaže výpalkov Flat net, 100 mm duplex, eight points
Stone and quarry Bloky, štiepaný kameň, dlažobné kocky Forma tašky, 150 mm sieťoviny, rohové záplaty
Porty a terminály Bagged and unitised cargo, quay work Flat net on a spreader, vytlačené WLL
Drevo Sawn packs, palice, sleepers Flat or bag, 150 – 200 mm sieťoviny
Šrot a recyklácia Zmiešaný a abrazívny šrot Veľká sieťovina, wear bands at the corners
Prefabrikovaný betón Units, krúžky, panelov Flat net with edge sleeves, eight points

Často kladené otázky

Je 20 t rating for the net or for the whole assembly?

The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, okovy, spreader and slings above must be rated at least 20 t as well.

Why is the safety factor 7:1 a nie 5:1?

7:1 is the factor we build to for this class, which gives a 140 t minimálne medzné zaťaženie pre a 20 t rating. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.

Polyester or nylon for a 20 t zdvihnúť?

Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.

How big a net do I need for a 2 × 2 m load?

At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.

Can it be lifted by a single hook?

Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.

Can you print our brand and the WLL on the net?

Yes — WLL, arrangement, čistá veľkosť, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.

Vyžiadajte si cenovú ponuku

Send the load and how it is presented

The cargo — what it is, ako je to zabalené, and the weight as presented for the lift;

The footprint — length × width, plus height if a bag form is needed;

The lift — four or eight points, výška háčika, and whether a spreader beam is available;

The duty — how many lifts a week, indoors or on a quay, and the temperature range;

The paperwork — CE marking, test report and own-brand printing if you need them.

Send the load and the footprint for a quotation →

Kam ďalej

Lift Sling Rigging Company · Vzdušný priemyselný park, Mesto Taizhou, Provincia Jiangsu, Čína · Kód HS 630790
Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Nechajte svoju správu

Prejdite na začiatok