لفٽ اسلنگ رگنگ ڪمپني جي پيداوار 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.
5 Ton Heavy Duty Ratchet Straps
50 ايم ايم پالئیےسٹر ويبنگ, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 جي طرف 10 m معياري طور تي, ايل سي 2,500 ۽, ايس ٽي ايف 350 daN at 50 ۽ هٿ قوت. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.
Part of the ڳنڍڻ وارو ٽنگ and lashing range. جي 50 mm specification in isolation sits on the 50 ايم ايم 5000 kg ratchet lashing belt صفحو.
What “5 Ton” Actually Means on a Ratchet Strap
Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. EN جي تحت 12195-2 the webbing of a lashing strap must reach at least twice its lashing capacity, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.
| شڪل | Value on the 50 mm assembly | جيڪو بيان ڪري ٿو | How it gets misread |
|---|---|---|---|
| گھٽ ۾ گھٽ ٽوڙڻ واري طاقت | 5,000 ۽ (5,000 ڪلو) | اهو لوڊ جنهن تي اسيمبلي پل ٽيسٽ ۾ ناڪام ٿئي ٿي | Read as the working figure — the mistake that overloads a trailer |
| ڇڪڻ جي گنجائش (ايل سي) | 2,500 ۽ (2.5 t) | The restraint the assembly is rated to hold, printed on the label | لفٽنگ سلنگ جي WLL جي مقابلي ۾, which is a different duty altogether |
| معياري ٽينشن قوت (ايس ٽي ايف) | 350 daN at 50 ۽ هٿ قوت | The tension one person reaches with the ratchet handle | LC سان پريشان, تنهن ڪري آپريٽر مفيد نقطي کي ختم ڪندو رهي ٿو |
ڇو ته 50 mm Build Is the Heavy-Duty Default
Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. جي 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.
| ويب جي ويڪر | Typical LC | ٽوڙڻ واري طاقت | What it is bought for |
|---|---|---|---|
| 25 ايم ايم (1 ۾) | 400–500 daN | 800–1,000 daN | Tool boxes, light restraint, tight anchor eyes |
| 35 ايم ايم (1-3/8 ۾) | 750 ۽ | 1,500 ۽ | Van and trailer decks, general cargo |
| 38 ايم ايم (1-1/2 ۾) | 1,000–1,500 daN | 2,000–3,000 daN | اسٽيل پليٽ, پائپ بنڊل, plant |
| 50 ايم ايم (2 ۾) | 2,500 ۽ | 5,000 ۽ | Heavy cargo restraint, ڪنول, مشينري, ڪنٽينر |
| 75-100 ملي ميٽر | 5,000 daN and up | 10,000 daN and up | Abnormal loads, where the bed allows the width |
The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.
Standard Specification of the 5 Ton Assembly
| شيءِ | تفصيل |
|---|---|
| جُٺ ڪرڻ | 100% اعلي استحڪام پالئیےسٹر, twill weave, UV مستحڪم, 50 mm ± 2% |
| بينڊ جي ٿلهي / ماس | 1.8 mm nominal / 88 g per metre |
| ڇڪڻ جي گنجائش (ايل سي) | 2,500 ۽ في اسيمبلي |
| گھٽ ۾ گھٽ ٽوڙڻ واري طاقت | 5,000 ۽ (2:1 against LC) |
| معياري ٽينشن قوت (ايس ٽي ايف) | 350 daN at 50 ۽ هٿ قوت |
| ٽينشن ڪندڙ | Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle |
| ايل سي تي ڊگھائي | 7% يا گهٽ |
| خدمت جي درجه حرارت | -40 °C تائين +100 °C (polyester webbing) |
| معياري ڊگھائي | 3-10 م; 1–30 m to order |
| نشان لڳائڻ | ٺهيل ليبل: ايل سي, ايس ٽي ايف, ڊگھائي, بيچ نمبر, معياري حوالو |
| معياري | Designed, tested and marked to EN 12195-2 |
| HS ڪوڊ | 630790 |
The End Fitting Decides Whether the Strap Fits the Job
The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.
| ٺهڻ | Anchors to | Notes before ordering |
|---|---|---|
| Chassis rave hook | Flatbed side rail, chassis lip | Check rail thickness and that the hook throat clears it |
| Claw hook | Anchor rings, D rings, recessed eyes | Opening must clear the ring; load on the crown only |
| D ring / ڊيلٽا رنگ | Welded or bolted anchor points | Ring bore at least as wide as the webbing |
| Flat snap hook | اي ٽريڪ, slotted rail, سوراخ | Confirm slot width; snap gate must close fully |
| S hook | پائپس, ريل, frame members | Both ends must seat without point loading on a weld |
| Sewn loop / looped ends | Around the load or through a bore | Nothing metal at the load; ideal for finished surfaces |
| لاتعداد, مناسب ناهي | Girth only — hulls, ڪنول, بنڊل | See the endless loop build below |

جي 5 Ton Strap in Two Special Builds
Polyester covers most freight, and it fails predictably when it is out of its depth: چوڌاري نرم ڪري ٿو 150 °C and melts at about 255 °C, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.
Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces
The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 يا 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 daN at 25 mm تائين 2,500 daN at 50 ايم ايم, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.
The grade decision is about chloride, لوڊ نه ڪرڻ. 304 (1.4301) handles rain, تازو پاڻي, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 ان عقيدي ۾ ته اهو مضبوط آهي غلط ملڪيت لاءِ ادا ڪرڻ. جتي ايپليڪيشن حفاظت سان لاڳاپيل آهي, انوائس جي تفصيل جي بجاءِ مل سرٽيفڪيٽ تي گريڊ جي تصديق ڪريو.
Two shop-floor notes worth passing on. stainless threads گل, so a dry 316 نٽ سخت ڊوڙندو a 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. ۽ لوڻ واري پاڻي ۾ ايلومينيم ڏانهن اسٽينلیس بولٽ هڪ ڪهڪشان جوڙو ٺاهي ٿو, so where the strap anchors to an alloy frame, رابطي کي الڳ ڪريو.
Full range and grade comparison: لامحدود اسٽينلیس سٹیل جي ڇت واري پٽي.
آرامي (ڪيلر) ratchet straps — for heat, sparks and cut edges
Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 °C. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.
The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.
Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.
How Many Straps Does the Load Actually Need?
Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.
| Straps used | Angle to the deck | Restraint per strap | Total restraint |
|---|---|---|---|
| 2 | 45° | لڳ ڀڳ. 1,750 ۽ | لڳ ڀڳ. 3,500 ۽ |
| 4 | 30° | لڳ ڀڳ. 1,250 ۽ | لڳ ڀڳ. 5,000 ۽ |
| 4 | 45° | لڳ ڀڳ. 1,750 ۽ | لڳ ڀڳ. 7,000 ۽ |
| 4 | 60° | لڳ ڀڳ. 2,165 ۽ | لڳ ڀڳ. 8,660 ۽ |
| 6 | 45° | لڳ ڀڳ. 1,750 ۽ | لڳ ڀڳ. 10,500 ۽ |
The arithmetic is an illustration, not a lashing plan: IN 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.
جتي جي 5 Ton Ratchet Strap Earns Its Keep
- فليٽ بيڊ, container and plant trailer restraint — the volume application for the 50 mm build.
- اسٽيل coil, سليب, billet and pipe bundles, with edge protection at the contact points.
- مشينري, moulds and skid-mounted plant, جتي هڪ 25 mm strap has neither the width nor the tension.
- ڪاٺ جا پيڪ, crates ۽ stillages, including the endless form that simply closes round the pack.
- Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
- مرين, marina and wash-down duty in 304 يا 316 where plated hardware would be a maintenance item.
- Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.

رنگ, Printing and Private Label
Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, نارنگي, پيلو, ڪارو, ڳاڙهو, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, ايس ٽي ايف, ڊگھائي, standard and traceability code. Cartons of 10 جي طرف 20 ٽڪرا, palletised for export, with neutral or own-brand packaging as required.
جاچڻ, Traceability and the Paperwork Buyers Ask For
Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. ٽيسٽ رپورٽون, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.
One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.
اڪثر پڇيا ويا سوال
هڪ آهي 5 ton ratchet strap rated to lift 5 ٽين?
نه, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.
Why does the same strap get called 5 ٽون ۽ 2.5 ٽن?
Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.
50 mm يا 38 mm for a flatbed?
50 ايم ايم, unless the anchor points are small. جي 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; جي 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.
Do I need 304 يا 316 بي داغ?
316 where chloride is present — sea air, لوڻ اسپري, آئسنگ لوڻ, boatyards, کاڌي جا ٻوٽا. 304 is enough for rain, تازو پاڻي, condensation and indoor wash-down. The difference is corrosion resistance, طاقت نه.
At what temperature does polyester fail, and what does aramid do instead?
Polyester softens around 150 °C and melts at about 255 °C, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 °C, and chars at about 427 °C instead of melting. مٿي 400 °C, or against molten metal, both need a heat shield.
Can the strap be supplied with a printed brand and a custom length?
ها. ويڪر, تائين ڊگھائي 30 م, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.
اقتباس جي درخواست ڪريو
Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, ماحول (salt, گرمي, ڌوئڻ), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.
لفٽ سلنگ ريگنگ ڪمپني
Lifute صنعتي پارڪ, Taizhou شهر, جيانگسو صوبي, چين
ٽيليفون: +86 523 8693 5818 · WhatsApp: +86 180 6600 2268
اي ميل: 702461526@qq.com · HS code 630790
لاڳاپيل مصنوعات
- Ratchet straps — the full lashing range, 25 mm تائين 100 ايم ايم.
- 50 ايم ايم 5000 kg ratchet lashing belt — this specification in detail.
- Endless loop ratchet strap — closed loop, نه ٿلهو, for girth-only loads.
- Endless stainless steel ratchet strap - 304 يا 316 for salt and wash-down.
- Aramid flame retardant ratchet straps - 200 °C مسلسل, 400 °C چوٽي.
- پالئیےسٹر ويببنگ سلنگ — when the job is lifting rather than lashing.

