مصنوعات جا زمرا

Steel Pipe Lifting One Way Webbing Sling

مختصر وضاحت:

Lift sling rigging company produce Steel Pipe Lifting One Way Webbing Sling,Lifting Slings For Steel and Steel Tube.

One-way webbing sling for steel pipe and tube: 25-300 mm polyester, 1-24 t, اک ۽ اک يا لامحدود, cut to your pick spacing. Printed to your reference.

پيداوار جي تفصيل

Lift sling rigging company produce Steel Pipe Lifting One Way Webbing Sling,Lifting Slings For Steel and Steel Tube.

One-way sling · eye and eye · steel pipe and tube

Steel Pipe Lifting One Way Webbing Sling

ٻه اکيون, ٻه چونڊون, one journey — a flat woven band cut to the pick spacing of the lift and printed with the tonnage it will carry.

1-24 ٽي WLL range 25-300 ملي ميٽر بينڊ جي چوٽي ×1.4 two legs to 45° ±2 % length tolerance
steel pipe lifting one way webbing sling carrying a galvanised pipe bundle

This is the eye-and-eye form of the one-way sling, and it is the form that suits most steel pipe and tube consignments: a flat polyester band with a formed eye at each end, one eye on each hook, the band bearing under the pipe or round the bundle. It is bought against a consignment rather than issued from a sling store, and it goes with the load instead of coming back. Working load limits run from 1 t کان 24 t, بينڊ جي چوٽي کان 25 mm تائين 300 ايم ايم, ۽ ڊگھائي کان 0.5 m کان 100 م, at a factor of 5:1, 6:1 يا 7:1.

تڪڙو جواب: for pipe the sling is specified by the pick positions. The length is the distance from the hook down to each pick, the capacity is set by the angle the legs make with the vertical, and the width is set by what the pipe surface will tolerate. Tonnage alone does not describe the article.

ٻه اکيون, ٻه چونڊون, and what that decides

The same one-way discipline is sold in three shapes, and the shape is decided by what is at each end of the band. On pipe work the eye-and-eye form is the general answer because a pipe is usually picked at two points along its length, with something to hook to above each one.

ٽيبل 1 — The three shapes a one-way sling is bought in, for pipe work
Shape What is at each end How the pipe is held When it is the right buy
Eye and eye — this page A formed flat eye, stitched and bar-tacked One eye on each hook, band under the pipe or round the bundle Two picks along the length, with a hook, pin or shackle above each
لاتعداد لوپ Nothing — a closed ring Wrapped round the pipe and back through itself, or doubled as a basket Where there is no fitting to thread and the band must close on itself
اڪيلو اک One eye and a plain tail ڇڪيل: the tail passes back through the eye and the noose closes Where the pipe must be gripped rather than hung, or left slung on arrival

The single-eye version is written up separately, because a choke changes both the arithmetic and the length: ڏسو هڪ طرفي لاتعداد کڻڻ واري سلنگ, هڪڙي اک, for steel pipe and tubing. The endless loop is for the same loads with no hardware at either end — بند ٿيل انگوزي فارم is on its own page as well. Nothing prevents a consignment using more than one shape, but each has to be specified and counted separately.

The figure on the band is per leg — the angle decides what a pair will carry

A two-leg lift is never twice one sling. The legs lean towards each other, so each leg carries more than half the load and the pair carries less than two bands’ worth. The design factor table used for synthetic webbing slings states it plainly, and the reference angle is measured from the vertical, not between the legs.

ٽيبل 2 — Mode factor by arrangement, and what a 5 t sling becomes
بندوبست زاويه فڪر ظرف
اڪيلو پير, عمودي - × 1.0 5,000 ڪلو
ٻه پير 0-45° عمودي کان × 1.4 7,000 kg per pair
ٻه پير 45-60° عمودي کان × 1.0 5,000 kg per pair
ٻه پير beyond 60° not permitted -
ٽوڪري, both parts vertical 0° × 2.0 10,000 ڪلو
ٽوڪري, parts at 45–60° - × 1.4 7,000 ڪلو
ڇڪيل - × 0.8 4,000 ڪلو

Worked case. اي 9 t joint of 508 mm pipe, picked at two points, ٿلهو 4 m above the pipe, pick spacing 6 م. Each leg is √(3² + 4²) = 5.0 m long and makes 36.9° with the vertical, so the pair is worth 1.4 × WLL. To carry 9 t the slings must be rated 9 ÷ 1.4 = 6.4 t each, ۽ هڪ 7 t band is the answer. Halve the hook height and the same pipe needs 9 t bands — the pipe did not change, the geometry did.

steel pipe suspended on two one way webbing slings in a workshop
ٻه پير, one pick near each end: the arrangement this page is written around.

Where the picks go on a pipe

پائپ هڪ شعاع آهي, and where it is supported decides whether it sags, whips or bends at the overhang. The classical layout for a uniform span puts the supports at about 0.21 L from each end, which makes the sag in the middle equal to the overhang at the ends; many yards simply use the quarter points, which is close enough on a stiff wall and easier to measure. Neither figure is a rule from a standard — it is a layout, and the layout is what the sling length is cut to.

ٽيبل 3 — Pick layout by joint length (single joint, ٻه چونڊون)
Pipe length Pick position from each end Span between picks نوٽس
تائين 6 م 1.5 م (quarter points) 3 م ٻه چونڊون, one hook or two
6 - 12 م 0.21 ايل, يا 2 م گھٽ ۾ گھٽ 0.58 ايل The usual range for line pipe
12 - 18 م 0.21 ايل 0.58 ايل Four picks or a spreader above
مٿان 18 م Two pick groups - Spreader beam rather than a long V
بنڊل One pick per sling position Set by the pack Girth, not length, sets the band
pick positions marked on a coated steel pipe before lifting
The pick positions marked on the pipe itself: the only instruction that still exists at the far end of the journey.

Two practical points that decide more lifts than the table does. A pick must not sit on a weld seam or a coating repair, and it must clear the end collar: an end that is thicker than the barrel will take the band on its shoulder and cut it. On a joint with a bevelled or sheared end, the band goes behind the bevel, never on it.

webbing sling in a basket hitch around a bundle of steel tubing
A basket hitch on tube: two parts of the band share the load, provided both are vertical. Lean them and the pair stops being worth twice one.

Length from pick spacing and hook height

On a two-leg lift the band is not a height, it is a hypotenuse. Given the spacing between the picks and the height of the hook above the pipe, the leg length and the angle follow directly — and the angle, نه ٽونيج, is what changes the capacity of the pair.

Leg length = √((spacing ÷ 2)² + hook height²), ۽ angle from vertical = arctan((spacing ÷ 2) ÷ hook height). Add the eye take-up at both ends — roughly the eye clear length — and order to the next half metre. A sewn article holds ±2 % on length.

ٽيبل 4 — Leg length and capacity for a pair of 5 t slings
Pick spacing Hook height ٽنگ جي ڊگھائي Angle from vertical Pair capacity
4 م 4 م 4.47 م 26.6° 7,000 ڪلو
6 م 4 م 5.00 م 36.9° 7,000 ڪلو
8 م 5 م 6.40 م 38.7° 7,000 ڪلو
10 م 4 م 6.40 م 51.3° 5,000 ڪلو
12 م 5 م 7.81 م 50.2° 5,000 ڪلو
12 م 7 م 9.22 م 40.6° 7,000 ڪلو
16 م 6 م 10.00 م 53.1° 5,000 ڪلو
16 م 9 م 12.04 م 41.6° 7,000 ڪلو

The capacity column is the pair, not the leg, and it already includes the mode factor. Beyond 60° from vertical the arrangement is outside the factor table: raise the hook or shorten the spacing rather than adding tonnage.

This is why the same pipe can need two very different bands on two sites. A yard with a high gantry picks a 12 m joint with 5 t legs; a shed with low headroom, picking the same joint at the same spacing, needs 7 t legs or a spreader to lift the pick points clear of the hook. The sling is the same length in both cases and a different article.

What the band bears on: ڀت, coating and the end

The width of the band is chosen by the surface it touches, ٽنهي جي حساب سان نه. A pipe is a line contact with a curved, sometimes thin, sometimes coated face — and the failure on pipe work is nearly always local: a cut, a scuff or an ovalised wall at the pick, not a band that broke in the middle.

ٽيبل 5 — Width and protection by pipe surface
پائپ بينڊ ويڪر Protection at the pick ان کان سواءِ ڇا ٿو ٿئي
Bare black pipe, ڀت 6 mm and up 75 - 100 ايم ايم None normally needed Cosmetic scuffing only
Bare pipe, wall under 4 ايم ايم 100 - 150 ايم ايم Wide band, pick behind the collar Ovalisation at the pick
کوٽيل, painted or lined 150 ايم ايم, 7.5 ايم ايم بينڊ آستين پائڻ, soft contact Coating damage becomes a rejection
Galvanised tube 100 - 150 ايم ايم Sleeve where the band turns Bright witness marks on the zinc
Bundled tube 150 - 200 ايم ايم Sleeve at the arris, if square-cut Band cut on a tube end
Stainless or aluminium 150 ايم ايم, sleeve as standard آستين, and a band that has never been used on steel Iron transfer, then corrosion

Two details cost almost nothing at the order and are impossible to add later: هڪ wear sleeve over the contact point, which is replaced with the band instead of the band being replaced, ۽ هڪ مضبوط ٿيل اکيون where a hook or shackle pin bears. On a one-trip article both are thrown away with the band, which is exactly why they are cheap.

pair of one way webbing slings with flat eyes for pipe lifting
اک ۽ اک, فليٽ اڻيل: اک اها بينڊ آهي جنهن کي پوئتي ڌڪيو ويو آهي, so the hook bears on a soft flat loop rather than on an edge.
white polyester webbing sling with reinforced red eye
A reinforced eye in a sleeve where the hook bears. On pipe work it is the eye that wears first, بينڊ نه.

تفصيل

ٽيبل 6 — Eye-and-eye one-way sling, معياري وضاحت
پيرا ميٽر معياري تعمير نوٽس
جُٺ ڪرڻ Flat woven high-tenacity polyester, 25-300 ملي ميٽر 4 mm يا 7.5 ايم ايم بينڊ
ڪم لوڊ جي حد 1 t - 24 t في سلنگ عمودي, هڪ ٽنگ
ڊيزائن جو عنصر 5:1 / 6:1 / 7:1 Same WLL needs a wider band at 7:1
ختم ٿئي ٿو Formed flat eye at each end Stitched and bar-tacked; sleeved on request
Eye clear length 250 mm تي 1 t کان 650 mm تي 15 t Hook bowl or pin plus about 10 ايم ايم
ڊگھائي 0.5 م - 100 م Cut to the pick spacing; ±2 %
رنگ حڪم ڪرڻ; IN 1492-1 code up to 10 t A second channel for sorting
گرمي پد -40 °C تائين +100 °C پاليسٽر; not for molten metal
نشان لڳائڻ ڊبليو ايل ايل, ڊگھائي, فائبر, بيچ, توهان جو حوالو Printed on the band and on a sewn label
پيڪنگ کنيل, baled or cartoned Can travel inside the consignment
HS ڪوڊ 630790 Packing list line

The standard range

The works weaves nine tonnages on a 4 ايم ايم بينڊ ۽ نائن آن اي 7.5 ايم ايم بينڊ. Width follows the tonnage and the factor, and the minimum length steps up with the width rather than with the tonnage — which is the line that decides a short order.

ٽيبل 7 — Width by WLL and factor, with minimum length
ڊبليو ايل ايل بينڊ 5:1 6:1 7:1 منٽ. ڊگھائي
1 t 4 ايم ايم 25 ايم ايم 50 ايم ايم 30 ايم ايم 0.5 م
2 t 4 ايم ايم 50 ايم ايم 100 ايم ايم 60 ايم ايم 1.0 م
3 t 4 ايم ايم 75 ايم ايم 150 ايم ايم 90 ايم ايم 1.0 م
4 t 4 ايم ايم 100 ايم ايم 200 ايم ايم 120 ايم ايم 1.5 م
5 t 4 ايم ايم 125 ايم ايم 250 ايم ايم 150 ايم ايم 1.5 م
6 t 4 ايم ايم 150 ايم ايم 300 ايم ايم 180 ايم ايم 1.5 م
8 t 4 ايم ايم 200 ايم ايم 200 ايم ايم 240 ايم ايم 2.0 م
10 t 4 ايم ايم 250 ايم ايم 250 ايم ايم 300 ايم ايم 2.0 م
12 t 4 ايم ايم 300 ايم ايم 300 ايم ايم 300 ايم ايم 2.0 م
2 t 7.5 ايم ايم 25 ايم ايم 50 ايم ايم 30 ايم ايم 0.5 م
4 t 7.5 ايم ايم 50 ايم ايم 100 ايم ايم 60 ايم ايم 1.0 م
6 t 7.5 ايم ايم 75 ايم ايم 150 ايم ايم 90 ايم ايم 1.0 م
8 t 7.5 ايم ايم 100 ايم ايم 200 ايم ايم 120 ايم ايم 1.5 م
10 t 7.5 ايم ايم 125 ايم ايم 250 ايم ايم 150 ايم ايم 1.5 م
12 t 7.5 ايم ايم 150 ايم ايم 300 ايم ايم 180 ايم ايم 1.5 م
16 t 7.5 ايم ايم 200 ايم ايم 200 ايم ايم 240 ايم ايم 2.0 م
20 t 7.5 ايم ايم 250 ايم ايم 250 ايم ايم 300 ايم ايم 2.0 م
24 t 7.5 ايم ايم 300 ايم ايم 300 ايم ايم 300 ايم ايم 2.0 م

Two lines of reading are worth doing before the table is used. The two blocks share the same width ladder, so a band bought thicker for a delicate surface buys nothing if the width column was already right — thickness is for tonnage and wear, width is for the surface. And at 8 t and above the 6:1 column runs out of width: from that point the band is already at 300 ايم ايم, and the answer to more tonnage is a heavier block or two slings, not a wider band.

هڪ رستو, and what that adds to the order

The band travels with the pipe, is inspected once at issue, and is not recovered. That changes three things about how it is ordered, and none of them about how it is made.

  • Counted per pick, في پيڪيج. A bundle on two picks is two bands; a long joint on four picks is four. Add 2–5 % for the band that gets cut while the pack is made up, and put the number on the order rather than in someone’s head.
  • Marked to the consignment. ڪم لوڊ جي حد, length and your reference printed on the band — pack number, order number or part number — because that print is the only record the receiving site will have. جي one way sling category sets out the discipline in full.
  • Packed to arrive with the goods. Coiled and baled, cartoned, or packed into the crate beside the pipe so the bands land at the same time as the consignment instead of a week earlier.

The inspection at issue

There is one inspection in the life of a one-way band and it happens before the lift. Four places, هن ترتيب ۾:

  • The eyes. سِٽڻ, bar-tacks and the mouth of each eye — a broken stitch at an eye gives no warning at the load.
  • The band where it will bear. ڪَٽَ, ڇڪيون, گرمي کان چمڪندڙ, and any thin patch that shows daylight through the weave.
  • ڇپيل. If the WLL or the length cannot be read, the band cannot be matched to the pipe it was cut for.
  • اهو ڇا ۾ بيٺو آهي. گرٽ, swarf ۽ تيل رابطي ۾ سفر; a clean band is the only protection on the list that costs nothing.

اڪثر پڇيا ويا

How many slings does a 12 m joint of pipe need?

ٻه, at about 0.21 L from each end — 2.5 m in from either end, leaving a 7 m span — provided the wall carries the overhang. جي باري ۾ مٿي 18 م, or where the overhang whips, four picks or a spreader beam is the honest answer and the band count goes up with it.

Can one sling lift one end of a pipe?

Only for a short, سخت, light joint, and then it is a single vertical leg at 1.0 × WLL with the pipe hanging at an angle. On anything long the pipe rotates about the pick and the load walks; two picks are the arrangement, and the second sling is cheaper than the first accident.

اک ۽ اک, endless loop or single eye for pipe?

Eye and eye where there is a hook or a pin at each pick — the usual case. The endless loop where nothing must be threaded and the band closes on itself, which is also the kindest to a coated surface. The single eye where the pipe must be gripped in a choke and left slung on arrival. The three are separate articles and are counted separately.

How flat is too flat?

Beyond 60° from the vertical the two-leg arrangement leaves the factor table entirely, and the tension in each leg climbs steeply for very little gain in height. If the pick spacing is fixed and the headroom is not there, the answer is a spreader beam that lifts the pick points instead of a heavier pair of slings.

Will the sling mark galvanised or coated pipe?

A used band can: grit embedded in the weave polishes the zinc, and a band that has carried black steel leaves iron behind that shows up as rust later. A sleeve at the contact point, a band kept for coated work only, ۽ 150 mm of width instead of 75 mm are the three measures that prevent it.

Can the length be cut to my pick spacing exactly?

Yes — that is what the length on the order means. Send the spacing between picks and the height of the hook above the pipe, and the leg length comes out of the arithmetic in Table 4; add the eye take-up and round to the next half metre. The finished length is confirmed in writing before the bands are cut, to ±2 %.

Send the lift, نه رڳو tonnage

Six lines and the band can be cut

The pipe: قطر کان ٻاهر, ڀت جي ٿلهي, coating or finish, and whether it travels as a joint or a bundle;

The mass of one lift, and how many picks you intend to use;

The spacing between picks, and the height of the hook above the pipe;

The fittings at each pick — hook, shackle or pin — with their sizes;

The factor your market expects: 5:1, 6:1 يا 7:1;

The reference to print, رنگ, and the quantity per pack.

Send the pipe and the pick spacing for a quotation →

Lift Sling Rigging Co., لميٽيڊ · لفٽ انڊسٽريل پارڪ, Taizhou شهر, جيانگسو صوبي, چين · HS ڪوڊ 630790 · Tel / WeChat +86 180 6600 2268 · 702461526@qq.com

اڳتي ڪٿي وڃڻو آهي

لفٽ سلنگ ريگنگ ڪمپني · Lifute Industrial Park, Taizhou شهر, جيانگسو صوبي, چين · HS ڪوڊ 630790
ٽيليفون +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com · xulft.com

 

پنهنجو پيغام ڇڏي ڏيو

مٿي ڏانهن ڇڪيو