Products Categories

Cargo Lifting Net

Short Description:

Lift sling rigging company produce nylon rope cargo net, steel wire rope cargo net and high-strength webbing cargo net

Cargo lifting nets in nylon rope, polyester webbing and steel wire rope, 1-100 t. Mesh, size and lifting points to your drawing, tested per net.

Product Detail

Lift sling rigging company produce nylon rope cargo net, steel wire rope cargo net and high-strength webbing cargo net.

 

Cargo Lifting Net

Cargo lifting net loaded with rough stone blocks, lifted on four orange corner straps from a crane hook
Figure 1 – A cargo lifting net in service: the load sits inside the mesh and the four corner straps take the whole consignment from the crane hook.

A cargo lifting net turns a loose, stacked or bagged consignment into a single crane lift. The net closes around the whole load instead of choking individual pieces, and it carries that load from its corners rather than from one contact point, so cargo that cannot be repacked, banded or palletised can still be moved in one movement.

We manufacture cargo lifting nets in three woven constructions – high-tenacity nylon rope, galvanised steel wire rope and high-strength polyester webbing – across a rated capacity of 1 t to 100 t. Mesh opening, net size, border, lifting points and colour are made to your drawing, and every net is proof-load tested in our own plant before it is packed.

  • Rated capacity: 1 t – 100 t, stated for the way the net is rigged
  • Mesh opening: 50 mm – 400 mm, chosen from the smallest dimension of the cargo
  • Lifting points: 4 reinforced corners as standard, 8 points for a spreader beam
  • Safety factor: 5:1 / 6:1 / 7:1 depending on construction
  • Documentation: capacity label, material test report and CE marking
  • Standards: built to your nominated standard; ISO 9001 quality system

Which cargo lifting net suits your load?

The three constructions overlap in capacity, so the choice is normally decided by the cargo and the working environment rather than by tonnage alone. Use the table below as a starting point, then confirm the mesh, the net size and the lifting points with our engineers.

Table 1 – Construction by cargo type (guide)
Cargo Recommended construction Usual mesh Typical capacity
Bagged goods – fertiliser, grain, seed, feed Polyester webbing or nylon rope 100 mm 2 t – 10 t
Palletised cartons, boxed goods High-strength webbing cargo lifting net 100 x 100 mm 2 t – 10 t
Bricks, blocks, split stone Nylon rope net in bag form 100 mm – 150 mm 2 t – 25 t
Quarry run, aggregates, demolition debris Steel wire rope net 150 mm – 300 mm 10 t – 100 t
Logs, sawn timber, poles Nylon rope net, knotted 200 mm – 300 mm 2 t – 50 t
Steel plate packs, pipe bundles, sections Webbing net with edge protection, or wire rope net 100 mm – 200 mm 5 t – 50 t
Drums, tyres, coils Nylon rope net or webbing net 100 mm – 200 mm 1 t – 10 t
Machined, painted or plated parts Webbing net only – flat, non-marking bands 50 mm – 100 mm 1 t – 20 t
Scrap metal, mixed abrasive bulk Steel wire rope net 200 mm – 400 mm 10 t – 100 t
FIBC big bags, 1 t and 2 t Webbing net, or a purpose-made crane pallet cargo net 50 mm – 100 mm 1 t – 5 t

What a cargo lifting net is – and what it is not

A cargo lifting net is a woven lattice, not a bag and not a sling. Bands or strands cross at right angles to form an open mesh; the border and the corners carry the load; and the cargo sits inside the lattice rather than on top of it. That geometry is what makes a net useful: the load is distributed over a wide bearing face instead of being concentrated at a hook, a choke point or a fork pocket, so contact pressure drops and the surface of the cargo is left intact.

It differs from a sling in three practical ways. A net holds the cargo in three dimensions, so nothing can slide out sideways during the lift. A net can be loaded on the ground, spread flat, and only then closed around the goods, which means the goods never have to be lifted to be netted. And a net is rated as an assembly of corners, border and mesh, so its capacity is quoted for a stated rigging arrangement rather than as a single line pull.

Diagram of the three cargo lifting net constructions: knotted nylon rope, cross-woven steel wire rope with pressed ferrules, and flat polyester webbing
Figure 2 – Schematic of the three woven constructions: knotted or braided nylon rope (8-24 mm), cross-woven steel wire rope locked with pressed ferrules, and flat polyester webbing woven into a square mesh.

The four elements that set the rating

The strand or the band. Nylon rope, steel wire rope or flat webbing. This single choice sets the strength, the net weight, the surface contact and the resistance to abrasion, cut and heat.

The mesh opening. The size of the square or diamond aperture. It decides what stays inside the net and how much the net weighs. It is chosen from the smallest dimension of the cargo, never from the outside size of the net – a 6 m net with a 300 mm mesh will lose bricks through the mesh no matter how strong the rope is.

The border. A doubled or reinforced edge running the full perimeter, so the edge bands cannot unroll, spread apart or pull out under load. On a webbing net the border is double-layer stitched; on a rope net it is a doubled border rope spliced into the corners.

The lifting points. Four reinforced corner loops as standard, or eight points where the net is lifted from a spreader beam. Load must enter the corners and the border, never the middle of a panel. Loading the middle of a net is the most common way a sound net is destroyed in service.

Mesh opening of a knotted nylon cargo lifting net being measured with a vernier caliper
Figure 3 – Mesh opening measured with a caliper on a knotted rope net – the aperture, not the net size, decides what the cargo net will hold.

Cargo lifting net technical parameters

The table below puts the three constructions side by side. Values are our standard production range; anything outside it is built to drawing, and the rating that applies is the rating of the net as it is rigged, not the capacity of the crane above it.

Table 2 – Cargo lifting net specifications, all three constructions
Parameter Nylon rope net Steel wire rope net Webbing net
Material 100% high-tenacity nylon (polyamide) multifilament Galvanised steel wire rope; stainless 304 / 316 on request 100% high-tenacity polyester webbing; nylon or PP on request
Strand / band 8 – 24 mm rope, 3-strand laid or 8 / 12-strand braided (up to 32 mm on request) 6 x 19 for abrasion, 6 x 37 / 6 x 36WS for flexibility; 6 – 20 mm; FC or IWRC 50 mm webbing standard; 25 / 75 / 100 mm on request
Mesh opening 100 – 300 mm, square or diamond 150 – 400 mm, square 100 x 100 mm square standard; 50 – 300 mm on request
Joint / lock Netmaker’s knot, or knotless braided splice Pressed aluminium ferrule at every intersection Woven band crossings, stitched at the border
Border Doubled border rope, spliced into the corners Continuous border rope, ferrule-locked to the mesh Double-layer stitched border round the full perimeter
Lifting points 4 corner eyes; 8-point on request Pressed corner eyes with thimbles, or rings / master links 4 reinforced corner loops; 8-point and ring fittings on request
Rated capacity 1 t – 50 t 2 t – 100 t 2 t – 10 t standard; heavier to order
Safety factor 5:1 / 6:1 / 7:1 4:1 / 5:1 / 6:1 7:1
Elongation approx. 18 – 22% at break – absorbs shock load Very low – the mesh keeps its shape under steady load Low, approx. 7% at the working load limit
Abrasion and cut Good; a single damaged strand can be replaced locally Highest of the three Good, but must be kept off sharp edges
Corrosion Rot-proof; suited to wet and salt-water duty Galvanised as standard; stainless for marine and chemical service Rust-free polyester, UV stabilised
Working temperature -40 C to +80 C Hot and dirty service – confirm the duty with us -40 C to +100 C
Colour White, or dyed to order Galvanised / stainless finish Orange high-visibility, blue, black, green or custom
Certification CE, GS, ISO 9001; test report per net CE, ISO 9001; CNAS and DNV certified facility CE, GS, ISO 9001; test report per net

Net size and rated capacity

Standard sizes are listed below. Truck bed, container, hold and spreader dimensions are made to drawing, and the capacity quoted is the capacity of the finished net, tested before dispatch.

Table 3 – Standard cargo lifting net sizes
Net size (L x W) Typical capacity Typical use
2.0 x 2.0 m 1 t – 3 t Drums, machine parts, small components
2.5 x 2.5 m 2 t – 5 t Palletised and bagged cargo, container loading
2.5 x 6.0 m 4 t – 10 t Long cargo, pipe bundles, truck and trailer loading
4 x 4 ft (1.2 x 1.2 m) 2 t – 3 t Small loads, drums, machine parts (imperial markets)
82 x 82 in 2 t – 5 t Standard pallet footprint in imperial markets
6.0 x 6.0 m 10 t – 25 t Bulk bagged cargo, timber, scrap
8.0 x 8.0 m 25 t – 50 t Heavy bulk, stone, quarry and demolition work
Built to drawing 1 t – 100 t Truck bed, container, hold and spreader beam dimensions

Mesh opening: choose it from the smallest dimension of the cargo

Mesh is the parameter buyers most often get wrong, because it is chosen from the net size instead of from the load. The rule we apply is simple: the aperture must be smaller than the smallest dimension of the smallest piece that must not escape. The table below is the guide we use on quotation.

Table 4 – Mesh opening against cargo size (guide, confirmed on quotation)
Smallest cargo dimension Cargo example Mesh to specify
Under 50 mm Bottles, small castings, nuts and bolts, components in bulk 50 mm – closed or near-closed bag form
50 – 100 mm Bricks, bagged fertiliser, boxed goods, FIBC big bags 100 mm
100 – 200 mm Drums, cartons, split stone, sawn timber 150 – 200 mm
Over 200 mm Blocks, logs, scrap, demolition debris 250 – 300 mm, or 400 mm in wire rope

Lifting configuration and how the rating is stated

A cargo lifting net is rated as an assembly. The same net gives a different rating for a four-point vertical lift, a two-point lift and an eight-point lift from a spreader beam, because the number of load-bearing corners changes. Every net we supply is therefore labelled with its working load limit and, where a net is used in more than one arrangement, each arrangement is listed separately on the label. Quote the configuration you will actually use when you enquire – a rating copied from a catalogue without the configuration is not a rating.

Nylon rope cargo lifting net

A nylon cargo lifting net is knotted or braided from high-tenacity nylon rope. Each strand can move slightly inside its knot, so the net settles around an irregular stack instead of sitting on top of it, and nylon’s high elongation absorbs the shock when the crane takes up the slack. It is the usual choice for timber and logs, stone, drums, tyres, scrap and any load whose shape shifts as it is lifted.

Rope is also the most repairable construction: a damaged strand can be re-knotted or re-spliced locally and the net re-inspected, which matters on a site where a net is working daily. For polypropylene rope in the same construction, see the polypropylene rope cargo net sling.

Knotted nylon rope cargo lifting net laid flat with square mesh and corner ropes
Figure 4 – A knotted rope cargo lifting net laid flat: square mesh, doubled border and four corner ropes spliced into the perimeter.

Steel wire rope cargo lifting net

A steel wire rope cargo lifting net is cross-woven from galvanised wire rope and locked at every intersection with a pressed aluminium ferrule, so the mesh cannot open up or distort when the net is dragged across a quay or a truck bed. Wire rope is the construction for abrasion, sharp edges, hot surfaces and long service with little maintenance – quarry run, aggregates, demolition debris, scrap and heavy bulk.

It is the heaviest of the three and the least forgiving to finished surfaces, so it is normally specified where the cargo is rough. Where a wire rope net has to handle dressed material, we supply the same construction with sheathed contact sections, using the rope from our wire rope slings range.

Rope cargo lifting net spread on the floor while stacked coils are loaded onto it before the lift
Figure 5 – Loading a net on the ground before the lift: the cargo is stacked inside the mesh, so nothing has to be lifted twice.

High-strength webbing cargo lifting net

A high-strength webbing cargo lifting net is woven from flat polyester webbing. The bands cross at right angles to form an open square mesh, the border and corners take the load, and the whole net is soft enough to sit against bagged, boxed, painted or machined cargo without marking it. It carries the widest bearing face of the three constructions at the lowest net weight, which is why it is the default for palletised, bagged and unitised cargo in ports, on trucks and on site cranes.

Polyester has low elongation, so the mesh keeps its shape while the crane takes up the slack and the load stays square. The webbing is woven in our own mill, which is why band width, colour, mesh and capacity can be tuned to the load instead of bought in from a catalogue. It is the same webbing used in our webbing slings and endless round slings, so a net and a sling on the same lift are matched in elongation and colour coding.

Orange polyester webbing cargo lifting net with 100 mm square mesh laid out flat
Figure 6 – 50 mm orange polyester bands woven into a 100 x 100 mm square mesh, with a double-layer stitched border round the perimeter.
Corner detail of a webbing cargo lifting net showing stitched border and steel corner ring
Figure 7 – Corner detail: the stitched border, the reinforced corner and the ring that forms the lifting point. This is where a net wears first, and where inspection should start.

How a cargo lifting net is rigged

  • Four-point lift from a single hook. The four corner loops are gathered onto the hook or a master ring, so the net closes around the cargo as the crane takes up. This is the standard arrangement for bagged, palletised and unitised loads.
  • Eight-point lift from a spreader beam. The net stays square and the load stays level, which is what a long or wide consignment needs. Our lifting spreader beam takes the eight points and keeps the legs vertical.
  • Bag form. A closed three-dimensional net for loose goods that must not escape – bricks, split stone, bottles, small castings.
  • Flat net, cargo inside the mesh. For palletised, bundled or unitised loads that only have to be held together during the transfer.

Whatever the arrangement, load must go into the corners and the border. Three habits destroy nets faster than any cargo: loading the middle of a panel, dragging the net sideways with the crane, and lifting on fewer than the full set of lifting points.

What we need to quote a cargo lifting net

Table 5 – Information required for an accurate quotation
Information Why it matters
Load weight and load shape Sets the rated capacity and the number of load-bearing strands or bands under the cargo
Net length x width The net must be larger than the load footprint so the cargo sits inside the mesh, not on top of it
Mesh opening 100 x 100 mm is our webbing standard; smaller or loose items need a smaller aperture
Strand diameter or band width Sets strength and net weight; band width also sets the bearing face on the cargo
Lifting points Four corners as standard, or eight points and rings for a spreader beam
Crane, hook or spreader Determines whether the corners carry eyes, rings, shackles or thimbles
Environment UV, salt water, offshore or high-temperature duty decides the material and the treatment
Documentation CE marking, test report, declaration of conformity or own-brand labels

Inspection: what to check and when to retire a net

Inspect before every lift and record a formal inspection at the interval your site requires. Check the corner loops and the corner stitching first – that is where wear starts – then work round the border and the mesh.

Table 6 – Inspection points and retirement criteria
Check Retire the net if
Corner loops and corner stitching Stitching is broken, the loop is deformed, or the ring / thimble is cracked or worn
Border The border rope or border band is cut, unravelled or pulled out of the mesh
Strands or bands Any load-bearing strand or band is cut, deeply abraded, heat-glazed or chemically stained
Knots and ferrules A knot has slipped, or a ferrule is cracked, displaced or corroded through
Webbing Bands are cut, powdered by UV, or contaminated with oil, paint or chemicals that cannot be removed
Labels The capacity label is missing or illegible – an unlabelled net cannot be rated

Never repair a net by knotting a broken strand, welding a wire rope or heating a band. Repairs belong to the maker or to a competent person using the original materials, followed by a re-test where the standard requires it. Store nets clean, dry and off the ground, out of direct sun.

Where cargo lifting nets are used

Table 7 – Applications by sector
Sector What the net does
Ports and terminals Container stuffing and de-stuffing, palletised and bagged cargo, quay and hold work with a net that is soft, rust-free and easy to fold
Steel and fabrication Plate packs, bundles, machined parts and stillage loads where the surface must not be marked
Stone, quarry and aggregates Split stone, blocks, cobbles and abrasive bulk; wire rope where cut resistance decides the service life
Timber and forest products Logs, sawn packs and poles – a rope net settles around an irregular stack as it is lifted
Offshore and marine Deck and over-the-side transfer; nylon and polyester drain freely and do not rust
Agriculture and bulk bags Fertiliser, grain, seed and feed in bags and big bags, lifted whole without repacking
Recycling and scrap Mixed and abrasive scrap, where a wire rope net outlasts a textile one
Vehicle and plant loading RoRo and breakbulk loading, where a wide net spreads the load across the body and chassis; see our vehicle lifting net range

Two neighbouring ranges are often quoted with a lifting net: heavy duty truck cargo nets and container cargo nets for securing rather than lifting, and safety rope nets where the net protects people instead of holding cargo. Tell us which duty applies and we will confirm the construction – a securing net is not rated for lifting, and a lifting net is not a fall-arrest product.

Frequently asked questions

What is the difference between a cargo lifting net and a cargo net?

A cargo net is a general term that covers lashing, securing and climbing nets as well as lifting nets. A cargo lifting net is a rated assembly: it is designed for a stated working load limit, tested, labelled and supplied with documentation. If a net has no capacity label, treat it as a securing net and never lift with it.

How do I choose between nylon rope, wire rope and webbing?

Rough, hot or abrasive bulk points to steel wire rope. Cargo that must not be marked points to webbing. Irregular loads that have to settle into the net, and wet deck work, point to nylon rope. Where two of those apply at once, tell us and we will recommend the construction with the trade-off made explicit.

What safety factor should I specify?

Our standard ranges are 5:1, 6:1 and 7:1 for rope and webbing nets and 4:1 to 6:1 for wire rope nets. The factor must satisfy the standard your site works to, so confirm it at enquiry rather than assuming the lowest option is acceptable.

Can a cargo lifting net be made to my size and mesh?

Yes. Size, mesh, strand diameter or band width, number of lifting points, colour and capacity are all made to order, including truck bed, container, hold and spreader dimensions. Send a drawing or the internal dimensions of the space the net has to work in.

Will the net hold loose material such as bricks or split stone?

Yes, in bag form with the correct mesh. The aperture must be smaller than the smallest piece, and the net must be closed on all sides. Where material is very fine or very sharp, we will normally propose a smaller mesh in a heavier construction.

Can the net be used in a marine or offshore environment?

Yes. Polyester and nylon nets are UV stabilised and rust-free, wire rope nets can be supplied galvanised or in stainless steel, and all three drain freely on deck. For offshore duty, tell us the salt-spray exposure and the inspection regime so the material and coating are matched to it.

Is a test certificate supplied with each net?

Yes. Each net leaves the plant with a capacity label and a material test report, and our facility holds CNAS, CE and ISO 9001 certification. Own-brand labels, printed markings and declarations of conformity are available on OEM orders.

What is the minimum order quantity?

There is no fixed minimum for standard constructions – a single net for a trial is possible, and batch quantities can combine mixed sizes and mixed constructions in one order. Mixed pallets are also acceptable where the export packing allows it.

How is a cargo lifting net packed for export?

Folded and strapped with the label and test report attached, then bag or crate packed as agreed. Export packing is built to survive sea freight, and nets can be supplied with a repair kit and a spare corner loop where the customer maintains its own fleet.

Can you print our logo or brand on the net?

Yes. We weave and print webbing in house, so brand names, capacity text, fleet numbers and colour coding can be incorporated in the net rather than added as a tag. Send the artwork with the enquiry.

Why buy cargo lifting nets from Lift Sling Rigging Company

  • 40 years of lifting equipment manufacturing – founded in 1985 in Taizhou, Jiangsu, with more than 200 employees and one of China’s largest sling and net production bases.
  • We weave our own webbing and make our own rope nets – band width, colour, mesh and capacity are under our control, so a net is tuned to the load instead of being bought in from a catalogue.
  • Own testing laboratory and a 1000 t horizontal test machine – breaking load is tested per net and documented; the facility holds CNAS, CE and DNV certification and 15 authorised patents.
  • One supplier for the whole cargo range – cargo lifting nets, webbing slings, round slings, wire rope slings, spreader beams, nylon ropes, cable pulling socks and safety nets.
  • OEM and ODM – own-brand labels, printed webbing, custom colours and export packing for distributors and end users.
Lift Sling Rigging Company factory entrance in Taizhou, Jiangsu, where cargo lifting nets are woven and tested
Figure 8 – Nets are woven, stitched, ferrule-pressed and tested in the same plant, which is why a quoted net and a delivered net match.

Request a cargo lifting net quotation

Send the load weight and shape, the net size, the mesh opening, the lifting points and the environment – or a drawing of the truck bed, container or hold the net has to fit. Our engineers will confirm the construction, the rated capacity, the strand or band size and the packing, and quote in one reply. To talk it through first, contact our engineers; our certification and test records are available on request.

Lift Sling Rigging Company
Lifute Industrial Park, Taizhou City, Jiangsu Province, China
Tel: +86 523 8693 5818 | WhatsApp: +86 180 6600 2268 | E-mail: lift98@jslift.com
HS code: 630790

Leave Your Message

Scroll to Top