Категории продуктов

Сверхмощный 20 Ton Polyester Cargo Lifting Net

Краткое описание:

Компания по производству такелажных подъемников производит Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

20 t polyester cargo lifting net: 7:1 коэффициент безопасности, 100 mm duplex bands, four or eight points, cut to the load footprint and proof tested per net.

Детали продукта

Компания по производству такелажных подъемников производит Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

Cargo lifting net · polyester · 20 t class

Сверхмощный 20 Ton Polyester Cargo Lifting Net

А 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

20 т предел рабочей нагрузки 140 т minimum breaking load 100 мм дуплексный диапазон 8 lifting points
Heavy duty polyester flat webbing cargo lifting net laid out, wide bands in a square mesh

A heavy duty 20 ton polyester cargo lifting net is a flat lattice of wide high-tenacity polyester bands, stitched into a square mesh with a doubled border and four or eight reinforced lifting points. The load sits inside the mesh and is carried across the full width of every band beneath it, so the pressure on the cargo is spread over a face rather than concentrated on four sling legs.

We build these nets to order in Taizhou: band width and layer, сетка, чистый размер, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.

The number behind “20 ton”. The working load limit is 20 t and the safety factor is 7:1, so the net’s minimum breaking load is 140 т. That figure is what the test bed proves; тот 20 t is what you are allowed to lift, in the arrangement the net was rated in.

Why polyester at this rating

В 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.

Стол 1 — Polyester against nylon for a 20 t net
Полиэстер (ДОМАШНИЙ ПИТОМЕЦ) Нейлон (Пенсильвания)
Stretch under a steady load Low — the net stays square and the load stays level Markedly higher; the net settles and the load can tilt
Амортизация Умеренный Best in the family; 18–22 % удлинение при разрыве
Водопоглощение Очень низкий, dries quickly О 4 %, with some strength loss when saturated
Repetitive crane cycles The usual choice Better where pickups are rough
Рабочая температура от −40 °C до +100 °С Lower at the top end
Best fit for a 20 t load в мешках, palletised, bundled or stacked cargo lifted on a cycle Irregular or shocky loads that must settle into the mesh
Nylon rope cargo net for comparison with a flat webbing net
The rope alternative: better on irregular loads, but it stretches far more than a polyester band net under a steady 20 т.

What changes when the rating goes to 20 т

Capacity is not a property of the net’s size. It comes from four things moving together: группа, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.

Стол 2 — Build steps from a light net to a 20 t net
Load band Band and build сетка Точки подъема What else changes
2 – 5 т 50 mm single layer 100 мм 4 corners Standard warehouse net
5 – 10 т 50 – 75 мм, duplex on the load run 100 мм 4 corners, 8 по запросу Heavier border, reinforced loops
10 – 20 т 75 – 100 мм дуплекс 100 – 150 мм 8 points Master ring or spreader beam; net built to drawing
20 – 30 т 100 мм дуплекс, band count from the load face 150 мм 8 points Spreader beam in the assembly; proof test per net
Выше 30 т 100 mm multi-layer or wider pitch 150 – 200 мм 8 points or more Engineered and tested to the lift, not to a catalogue

Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.

Отсюда следуют два последствия. Первый, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 т на а 10 t ring is a 10 т сборка. Второй, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Corner detail of a heavy duty webbing cargo net, folded double-stitched border and reinforced loop
Угловая деталь: the doubled border is spliced into the loop, which is where the whole 20 t passes through — and where a net is inspected first.

Sizing the net to a 20 t load

A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.

  • Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. А 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
  • Форма сумки: the flat width has to wrap up the sides and close over the top, так плоская ширина = занимаемая площадь + 2 × bag depth. А 1.2 m footprint in a 0.6 m deep bag needs about 2.4 м в поперечнике.
  • Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.
Flat polyester cargo lifting net spread on the floor with four corner lifting loops
Flat form: the net overhangs the load footprint and the four corners gather on the hook, so the cargo sits inside the lattice rather than on top of it.

сетка: sized from the cargo, не тоннаж

Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.

Стол 3 — Mesh against the smallest piece in the load
Наименьший размер груза Typical cargo at 20 т Сетка для указания
Под 75 мм Маленькие отливки, компоненты оптом, drummed goods 100 мм алмаз, или закрытая сетка для сумок
75 – 150 мм Кирпичи, упакованные товары, расколотый камень 100 – 150 мм
150 – 250 мм Sawn packs, bundled tube, коробки, металлолом 150 – 200 мм
Над 250 мм Блоки, большой камень, обломки сноса 200 – 300 мм

Спецификация

Стол 4 — Heavy duty 20 ton polyester cargo lifting net
Параметр Спецификация
Тип Open flat webbing lattice, четыре или восемь точек подъема
Материал ремешка 100 % высокопрочный полиэстер (ДОМАШНИЙ ПИТОМЕЦ); nylon or UHMWPE on request
Ширина полосы 75 – 100 mm for this class
Band build Дуплекс (двойной слой) on the load-bearing run, single layer elsewhere
Сетчатое отверстие 100 – 150 мм; square standard, diamond on request
Чистый размер Обычно 4.0 × 4.0 м до 6.0 × 6.0 м, or to the load footprint
Предел рабочей нагрузки 20,000 kg in the rated arrangement
Фактор безопасности 7:1 — минимальная разрывная нагрузка 140,000 кг
Граница и углы Doubled border, spliced into the corners; reinforced loops, four or eight
Фитинги Мастер-кольцо или сорт 80 кандалы; spreader beam for eight-point lifts
Уход УФ-стабилизированный, против старения, abrasion-resistant finish
Рабочая температура от −40 °C до +100 °С
Маркировка ВЛЛ, договоренность, net size and identification on a sewn label; band printing on request
Документация Capacity label, отчет об испытаниях материала, Маркировка CE; проверено на собственном опыте 1000 t bed
Код ТН ВЭД 630790
Polyester webbing cargo net with the border and lifting loops visible across its width
Border and loops: the perimeter takes the load from corner to corner, so no single stitch line carries the lift.

Eight points, не четыре, once the load is long

Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.

  • Four points suit square, compact loads where the net is only holding the cargo together;
  • Eight points suit long or wide loads, and any lift where the net must stay flat under load;
  • The spreader or master link, the slings above it and the hook must each be rated at least 20 т;
  • Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.

The leg sees more than the share: в 45 deg from the vertical, а 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.

Проверка и выход на пенсию

Стол 5 — What ends a net’s service life
Проверять Списать или отремонтировать, если
Corner loops and their stitching A loop is deformed, the stitching is broken, or the band is cut at the throat
Граница Граница перерезана, flattened, or has pulled out of a corner
Load-bearing bands Any band is cut, глубоко исцарапанный, heat glazed or chemically stained
Mesh geometry The lattice is distorted from an overload — the net no longer sits square
шитье Stitch lines are broken or pulled at a crossover
Label and printing The WLL or the arrangement is illegible — an unlabelled net cannot be rated

Inspect before each lift and have the net examined by a competent person at the interval your site sets. Храните его в чистоте и сухости, над землей и вдали от прямых солнечных лучей; never knot, weld or heat-repair a webbing net.

Steel coils loaded inside a webbing cargo net on a factory floor
Coils inside the mesh: at this rating the net is as much a handling tool as a container, and the crane never touches the cargo.

Как он построен, and how the rating is proven

  • Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
  • Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
  • Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
  • Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.

Тот же завод плетет лямки и прессует наконечники для тросов., which is why a net, а лямка строп и строп из троса on the same lift can be matched in rating rather than bought from three suppliers.

Где 20 t net does the work

Стол 6 — Sectors that buy this class
Сектор Что поднимает сеть Обычная сборка
Сталь и производство Пакеты, разделы, бардовые грузы Плоская сетка, 100 мм дуплекс, eight points
Stone and quarry Блоки, расколотый камень, булыжник Форма сумки, 150 мм сетка, угловые патчи
Порты и терминалы Bagged and unitised cargo, quay work Flat net on a spreader, печатная WLL
Древесина Sawn packs, столбы, sleepers Flat or bag, 150 – 200 мм сетка
Лом и переработка Смешанный и абразивный лом Большая сетка, wear bands at the corners
Сборный железобетон Units, кольца, панели Flat net with edge sleeves, eight points

Часто задаваемые

Это 20 t rating for the net or for the whole assembly?

The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, кандалы, spreader and slings above must be rated at least 20 t as well.

Why is the safety factor 7:1 и не 5:1?

7:1 is the factor we build to for this class, which gives a 140 t минимальная разрушающая нагрузка для 20 т рейтинг. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.

Polyester or nylon for a 20 т лифт?

Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.

How big a net do I need for a 2 × 2 m load?

At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.

Can it be lifted by a single hook?

Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.

Can you print our brand and the WLL on the net?

Yes — WLL, договоренность, чистый размер, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.

Запросить предложение

Send the load and how it is presented

The cargo — what it is, как оно упаковано, and the weight as presented for the lift;

The footprint — length × width, plus height if a bag form is needed;

The lift — four or eight points, hook height, and whether a spreader beam is available;

The duty — how many lifts a week, indoors or on a quay, and the temperature range;

The paperwork — CE marking, test report and own-brand printing if you need them.

Send the load and the footprint for a quotation →

Куда идти дальше

Компания по производству такелажных подъемников · Lifute Industrial Park, Тайчжоу город, Провинция Цзянсу, Китай · Код ТН ВЭД 630790
Тел. +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Оставьте свое сообщение

Прокрутить вверх