उत्पादन कोटिहरु

Single Ply Endless Lifting Sling

छोटो विवरण:

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Single ply endless lifting sling: one layer, one lapped joint, कुनै अन्त्य छैन. 4 मिमी ब्यान्ड, 1-12 t मा 7:1 दुई एक 1492-1, quoted by circumference or flat length.

उत्पादन विवरण

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Endless lifting sling · single layer · 4 mm flat band

Single Ply Endless Lifting Sling

One layer, one lapped joint, कुनै अन्त्य छैन. The lightest closed loop in the range: it folds into a pocket, turns a tight radius and drapes over the load — 1 t लाई 12 t मा 7:1 दुई एक 1492-1.

1-12 टी single ply ladder 4 mm band section 7:1 दुई एक 1492-1 25-300 मिमी ब्यान्ड चौडाइ
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets

A single ply endless lifting sling is the single-layer build of the closed loop: one band of high-tenacity polyester, lapped over itself and closed with dense parallel rows of stitching, आँखा बिना, no fittings and no metal anywhere on the article. यो EN को अनन्त प्रकारको ए फ्ल्याट बुनेको वेबिङ स्लिङ हो 1492-1 — the type 5 web sling in North American usage.

The word to be careful with is ply. It does not mean two slings or two bands in parallel; it means how many layers of webbing are woven into the one band the loop is made from. Single ply is one layer, and everything that follows — the 4 mm section, the weight per metre, the way it turns round a small radius, and the capacity it can be given at a given width — comes from that one decision.

The trade-off in one line. Single ply gives the most flexible loop and the lowest weight per metre; duplex gives more capacity at the same width, a stiffer bearing face and more abrasion reserve. बारेमा तल 6 t, and wherever the loop has to fold, single ply is the right default.

What one layer actually gives you

Four practical differences separate the single-layer loop from the duplex build, and each one shows up on a different job:

  • ए 4 mm section. The band folds into a pocket, coils onto a hook and passes between a load and a tight gap where a thicker band will not go.
  • Less weight per metre. The ladder below runs from 0.20 kg/m मा 1 t लाई 2.05 kg/m मा 10 t — a one-handed carry for the sizes most yards actually use.
  • More supple over a radius. One layer conforms to pipe, tube and rolled sections instead of standing off them, so contact is over the full width rather than at two edges.
  • एक संयुक्त, thin and easy to read. The lapped joint is the only made connection in the load path; in a single layer the stitching rows sit on one visible face, with no second layer masking them.
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets
Plate and sheet in a basket: one layer of band, doubled under the load, a full-width soft bearing face and no fitting anywhere near the steel.

Single ply against duplex, at the same width

The two builds are not two grades of the same thing; they are two answers to different questions. The comparison below is the one we use in quotation, and the widths are the published single-ply ladder.

तालिका 1 — Single ply and duplex, same nominal width
एकल प्लाई डुप्लेक्स
Layers in the band एक दुई, woven as one band
Section thickness 4 mm at the standard ladder Roughly twice the single-ply section
Capacity at a given width The ladder figure Higher — the reason duplex exists above the single-ply range
प्रति मिटर वजन 0.20 kg/m मा 1 t लाई 2.05 kg/m मा 10 t Higher for the same width
ह्यान्डलिङ Folds small, turns a tight radius, drapes onto the load कडा; sits flatter over an edge and resists abrasion longer
जहाँ जित्छ बारेमा तल 6 t, tight gaps, small diameters, mixed rigs High capacity in a narrow width, rough edges, heavy abrasion
संयुक्त One lap, stitching visible on the face One lap through the doubled band

The duplex build has its own page: double ply endless lifting sling.

The capacity ladder, एकल प्लाई

Working load limits are quoted in straight lift, मा 7:1 दुई एक 1492-1. Colour follows EN 1492-1 and is a capacity band, not a material; माथि 10 t there is no colour code and the label is the only rating.

तालिका 2 — Single ply endless sling: क्षमता, colour and weight
WLL, सीधा लिफ्ट रङ सन्दर्भ चौडाइ लम्बाइ दायरा लगभग. वजन चोक भयो (× 0.8)
1 t बैजनी अर्डरमा पुष्टि गर्नुहोस् 0.5 - 100 m 0.22 kg/m 0.8 t
2 t हरियो 50 mm 1 - 100 m 0.35 kg/m 1.6 t
3 t पहेंलो 75 mm 1 - 100 m 0.52 kg/m 2.4 t
4 t खैरो 100 mm 1.5 - 100 m 0.80 kg/m 3.2 t
5 t रातो 125 mm 1.5 - 100 m 0.85 kg/m 4.0 t
6 t ब्राउन 150 mm 1.5 - 100 m 0.96 kg/m 4.8 t
8 t निलो 200 mm 2 - 100 m 1.34 kg/m 6.4 t
10 t सुन्तला 250 mm 2 - 100 m 1.64 kg/m 8.0 t
माथि 10 t कुनै रङ कोड छैन Duplex build अर्डर गर्न अनुरोधमा लेबलले शासन गर्छ

Widths and weights are the published series for this range; the finished width, ply and weight are confirmed on the order acknowledgement.

चौडाइ, safety factor and the same capacity

A higher safety factor needs a wider band for the same working load limit, which is why the width column has three values. Tell us the standard your site works to and the sling is built to it; the figures below are the single-ply polyester ladder.

तालिका 3 — Band width by safety factor, 4 mm single ply polyester
WLL मा 5:1 मा 6:1 मा 7:1 मोटाई मा वजन 7:1
1 t (1 000 kg) 25 mm 25 mm 30 mm 4 mm 0.20 kg/m
2 t (2 000 kg) 50 mm 50 mm 60 mm 4 mm 0.60 kg/m
3 t (3 000 kg) 75 mm 75 mm 90 mm 4 mm 0.78 kg/m
4 t (4 000 kg) 100 mm 100 mm 120 mm 4 mm 0.90 kg/m
5 t (5 000 kg) 125 mm 125 mm 150 mm 4 mm 1.14 kg/m
6 t (6 000 kg) 150 mm 150 mm 180 mm 4 mm 1.33 kg/m
8 t (8 000 kg) 200 mm 200 mm 240 mm 4 mm 1.85 kg/m
10 t (10 000 kg) 250 mm 250 mm 300 mm 4 mm 2.05 kg/m
12 t (12 000 kg) 300 mm 300 mm 300 mm 4 mm 2.70 kg/m
Four single ply endless slings in white, बैंगनी, green and black
The capacity colour is woven in, not printed on: white for the general band, violet for 1 t, green for 2 t, with one black transverse stripe per tonne as a second check.

संयुक्त, and why it is the first thing to look at

An endless sling is endless in use, निर्बाध छैन. The band is lapped over itself and closed with dense parallel rows of stitching; that lap is a full-strength joint and it sits in the load path. It is the only made connection in the whole article.

On a single-layer loop that joint is easier to inspect than on a duplex one, because the stitching rows lie on one visible face rather than between two layers. Look for broken or pulled stitches, a lap that has started to open, and abrasion where the lap passes over an edge. If the joint is sound, the rest of the loop is one continuous band and can be read anywhere along its length.

White single ply endless sling laid out on gravel
एउटा ब्यान्ड, lapped and stitched once. That single joint is the only made connection in the load path, and the first thing an inspector reads.

Three hitches from the same loop

The marked figure is the straight-lift rating; every other arrangement is derived from it. Size the sling to the hitch the crew will actually rig, not to the one in the lift plan.

तालिका 4 — Mode factor by hitch
हिच मोड कारक What it means on site
ठाडो × 1.0 The label figure applies directly
चोक भयो × 0.8 ए 4 t एक चोक मा लोड a आवश्यक छ 5 t sling — the wrap grips as the load comes on
टोकरी, ठाडो नजिक खुट्टा × 2.0 Both sides of the loop carry the load and the bearing face is doubled
टोकरी, 7°–45° × 1.4 As the legs open the rating falls; plan the angle, not only the weight
टोकरी, 45°–60° × 1.0 At wide angles the basket advantage is gone — treat it as a straight lift

लम्बाइ: परिधि, or the height you actually get

बन्द लुपको कुनै अन्त्य हुँदैन, त्यसैले अन्त देखि अन्त मापन गर्न को लागी केहि छैन. This trade quotes the same sling two ways, र तिनीहरू दुई को एक कारक द्वारा भिन्न छन्: the circumference is the perimeter of the loop, while the effective working length is the usable height you get, roughly half the circumference because the loop is doubled when it hangs.

तालिका 5 — The same sling under both conventions
को रूपमा उद्धृत गरियो यसले के मापन गर्छ एउटै गोली बराबर हुन्छ
परिधि The perimeter of the loop — total band in the article 2 m
प्रभावकारी काम लम्बाइ प्रयोगयोग्य उचाइ; the loop doubles when it hangs 1 m

Name the convention with the figure, वा यसको सट्टा प्रयोगको अवस्था बताउनुहोस् — लेखको परिधि लुपले घुमाउनुपर्छ — र ब्यान्ड काट्नु अघि अस्पष्टता गायब हुन्छ.

Green single ply endless sling with its blue capacity label
सिलाई भएको लेबलले काम गर्ने भारको सीमा बोक्छ, सामग्री, मानक, the length and the batch — on a closed loop it is the whole record of the article.

पलिएस्टर, and the limits of it

The standard build is 100% उच्च दृढता पलिएस्टर (PES). It elongates no more than 3% at the working load limit and no more than 10% ब्रेकिङ लोड मा, so the load does not creep down as the lift comes on, and the standard build works from −40 °C to +100 °C. Nylon is offered where shock and abrasion dominate; polypropylene where weight and cost matter more than strength; UHMWPE and aramid where strength-to-weight or heat is the deciding factor.

What ends a polyester build is the same list as for any synthetic sling: heat above the range, strong alkalis, sharp edges that cut rather than abrade, and a cut or a glaze anywhere on the circumference. On a closed loop there is no second end to compare, so condition is judged against the surrounding band.

Single ply endless slings lifting bundles of steel pipe at a loading bay
Pipe bundles at a loading bay: the loop is passed round the bundle and both sides come back to the hook, so the band is doubled where the load is heaviest.

Marking and traceability

  • IN 1492-1 capacity colour in the weave — violet 1 t, हरियो 2 t, पहेंलो 3 t, खैरो 4 t, रातो 5 t, खैरो 6 t, नीलो 8 t, सुन्तला 10 t.
  • One black transverse stripe per tonne as a second, optical check on the band itself.
  • A sewn label with the working load limit, सामग्री, मानक, length and traceability code — and above 10 t, the label is the only rating there is.
  • Every sling proof tested in our own laboratory before dispatch, with a test certificate per batch on request; HS कोड 630790.
Two single ply yellow endless slings showing the flat band and its thin section
The single-layer section is 4 mm: it folds into a pocket, turns round a small diameter and drapes over the load instead of standing off it.

बारम्बार सोधिने

What does single ply mean, exactly?

One layer of webbing in the band the loop is made from — not two slings, and not two bands side by side. It gives a 4 mm section at the standard ladder widths, the lowest weight per metre in the range, and the most supple loop we build.

Is an endless sling seamless?

छैन. यो प्रयोगमा अनन्त छ, निर्बाध छैन: the band is lapped over itself and closed with dense parallel stitching, and that lap is a full-strength joint in the load path. What a closed loop removes is the eyes and the end fittings, not the joint. If you need a closed loop with no joint in the load-bearing element at all, त्यो हो अन्तहीन गोल गोफन, where the core is continuous.

How far up the capacity range does single ply go?

The single-ply ladder is published to 12 t मा 7:1 in a 300 मिमी ब्यान्ड; the range as a whole runs to 30 t, and above the single-ply ladder the duplex build is the answer rather than a wider single band.

Can I use one loop for a vertical lift and a choke?

हो, and the figure changes with the arrangement: 1.0 ठाडो, 0.8 निसासिएको, 2.0 in a basket with the legs near vertical, मा खस्दै 1.4 and then 1.0 as the legs open. Size to the hitch the crew will actually rig.

Will a single ply sling mark aluminium or painted steel?

The band is synthetic fibre and no fitting touches the load, so it will not scratch or burr the way a chain or a wire rope can. Width is the protection measure — for mirror-finish or anodised work, specify a width above the capacity ladder and the pressure on the surface falls with it.

How should the length be quoted?

परिधि वा प्रभावकारी कार्य लम्बाइ द्वारा - दुई को लगभग दुई को एक कारक द्वारा फरक छ. अधिवेशनको नाम दिनुहोस्, or give the girth of the article the loop must go round, and the figure is confirmed on the order acknowledgement.

उद्धरण अनुरोध गर्नुहोस्

Five things settle a single ply loop

The load — what it is, its girth at the pick positions, and its surface;

The hitch — vertical, चोक वा टोकरी, and the leg angle if it is a basket;

The working load limit in that hitch, and the safety factor your site works to;

The length — with its convention, or the girth the loop has to go round;

The marking and packing — own-brand label, carton or pallet specification.

Send the duty and the figure for a quotation →

अब कहाँ जाने हो

लिफ्ट स्लिङ रिगिङ कम्पनी · Lifute Industrial Park, Taizhou शहर, जियाङसु प्रान्त, चीन · HS कोड 630790
टेलिफोन +86 523 8693 5818 व्हाट्सएप +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

आफ्नो सन्देश छोड्नुहोस्

शीर्षमा स्क्रोल गर्नुहोस्