उत्पादन कोटिहरु

भारी शुल्क 20 Ton Polyester Cargo Lifting Net

छोटो विवरण:

लिफ्ट स्लिङ रिगिङ कम्पनीले भारी शुल्क उत्पादन गर्दछ 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

20 t polyester cargo lifting net: 7:1 सुरक्षा कारक, 100 mm duplex bands, four or eight points, cut to the load footprint and proof tested per net.

उत्पादन विवरण

लिफ्ट स्लिङ रिगिङ कम्पनीले भारी शुल्क उत्पादन गर्दछ 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

Cargo lifting net · polyester · 20 t कक्षा

भारी शुल्क 20 Ton Polyester Cargo Lifting Net

ए 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

20 t काम लोड सीमा 140 t minimum breaking load 100 mm duplex band 8 lifting points
Heavy duty polyester flat webbing cargo lifting net laid out, wide bands in a square mesh

A heavy duty 20 ton polyester cargo lifting net is a flat lattice of wide high-tenacity polyester bands, stitched into a square mesh with a doubled border and four or eight reinforced lifting points. The load sits inside the mesh and is carried across the full width of every band beneath it, so the pressure on the cargo is spread over a face rather than concentrated on four sling legs.

We build these nets to order in Taizhou: band width and layer, जाल, शुद्ध आकार, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.

The number behind “20 ton”. The working load limit is 20 t and the safety factor is 7:1, so the net’s minimum breaking load is 140 t. That figure is what the test bed proves; द 20 t is what you are allowed to lift, in the arrangement the net was rated in.

Why polyester at this rating

मा 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.

तालिका 1 — Polyester against nylon for a 20 t net
पलिएस्टर (PET) नायलन (PA)
Stretch under a steady load Low — the net stays square and the load stays level Markedly higher; the net settles and the load can tilt
झटका अवशोषण मध्यम Best in the family; 18–22 % ब्रेक मा लम्बाइ
पानी अवशोषण धेरै कम, dries quickly बारे 4 %, with some strength loss when saturated
Repetitive crane cycles The usual choice Better where pickups are rough
काम गर्ने तापमान −40 °C देखि +100 °C Lower at the top end
Best fit for a 20 t लोड झोला लगाइयो, प्यालेटाइज गरिएको, bundled or stacked cargo lifted on a cycle Irregular or shocky loads that must settle into the mesh
Nylon rope cargo net for comparison with a flat webbing net
The rope alternative: better on irregular loads, but it stretches far more than a polyester band net under a steady 20 t.

What changes when the rating goes to 20 t

Capacity is not a property of the net’s size. It comes from four things moving together: ब्यान्ड, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.

तालिका 2 — Build steps from a light net to a 20 t net
Load band Band and build जाल लिफ्टिङ बिन्दुहरू What else changes
2 - 5 t 50 mm single layer 100 mm 4 corners Standard warehouse net
5 - 10 t 50 - 75 mm, duplex on the load run 100 mm 4 corners, 8 अनुरोध मा Heavier border, reinforced loops
10 - 20 t 75 - 100 मिमी डुप्लेक्स 100 - 150 mm 8 अंक Master ring or spreader beam; net built to drawing
20 - 30 t 100 मिमी डुप्लेक्स, band count from the load face 150 mm 8 अंक Spreader beam in the assembly; proof test per net
माथि 30 t 100 mm multi-layer or wider pitch 150 - 200 mm 8 points or more Engineered and tested to the lift, not to a catalogue

Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.

दुई परिणामहरू पछ्याउँछन्. पहिले, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 a मा t 10 t ring is a 10 t विधानसभा. दोस्रो, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Corner detail of a heavy duty webbing cargo net, folded double-stitched border and reinforced loop
कुना विवरण: the doubled border is spliced into the loop, which is where the whole 20 t passes through — and where a net is inspected first.

Sizing the net to a 20 t लोड

A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.

  • Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. ए 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
  • झोला फारम: the flat width has to wrap up the sides and close over the top, त्यसैले flat width = footprint + 2 × bag depth. ए 1.2 m footprint in a 0.6 m deep bag needs about 2.4 m across.
  • Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.
Flat polyester cargo lifting net spread on the floor with four corner lifting loops
Flat form: the net overhangs the load footprint and the four corners gather on the hook, so the cargo sits inside the lattice rather than on top of it.

जाल: कार्गोबाट आकार, टन भार होइन

Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.

तालिका 3 — Mesh against the smallest piece in the load
सबैभन्दा सानो कार्गो आयाम Typical cargo at 20 t निर्दिष्ट गर्न जाल
अन्तर्गत 75 mm Small castings, थोक मा घटक, drummed goods 100 mm diamond, or a closed bag net
75 - 150 mm ईंटहरू, bagged goods, विभाजित ढुङ्गा 100 - 150 mm
150 - 250 mm Sawn packs, bundled tube, कार्टन, स्क्र्याप 150 - 200 mm
माथि 250 mm ब्लकहरू, large stone, विध्वंस मलबे 200 - 300 mm

विशिष्टता

तालिका 4 — Heavy duty 20 ton polyester cargo lifting net
प्यारामिटर विशिष्टता
टाइप गर्नुहोस् Open flat webbing lattice, four or eight lifting points
ब्यान्ड सामग्री 100 % उच्च दृढता पलिएस्टर (PET); nylon or UHMWPE on request
ब्यान्ड चौडाइ 75 - 100 mm for this class
Band build डुप्लेक्स (डबल तह) on the load-bearing run, single layer elsewhere
जाल खोल्ने 100 - 150 mm; square standard, diamond on request
नेट साइज सामान्यतया 4.0 × 4.0 m देखि 6.0 × 6.0 m, or to the load footprint
काम लोड सीमा 20,000 kg in the rated arrangement
सुरक्षा कारक 7:1 - न्यूनतम ब्रेकिङ लोड 140,000 kg
सिमाना र कुनाहरू Doubled border, कुनाहरूमा काटियो; reinforced loops, four or eight
फिटिङ्स Master ring or grade 80 बाँधहरू; spreader beam for eight-point lifts
उपचार यूवी स्थिर, वृद्धावस्था विरोधी, abrasion-resistant finish
काम गर्ने तापमान −40 °C देखि +100 °C
चिन्ह लगाउँदै WLL, arrangement, net size and identification on a sewn label; band printing on request
कागजात क्षमता लेबल, सामग्री परीक्षण रिपोर्ट, सीई मार्किंग; tested on our own 1000 t bed
HS कोड 630790
Polyester webbing cargo net with the border and lifting loops visible across its width
Border and loops: the perimeter takes the load from corner to corner, so no single stitch line carries the lift.

Eight points, चार होइन, once the load is long

Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.

  • Four points suit square, compact loads where the net is only holding the cargo together;
  • Eight points suit long or wide loads, and any lift where the net must stay flat under load;
  • The spreader or master link, the slings above it and the hook must each be rated at least 20 t;
  • Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.

The leg sees more than the share: मा 45 deg from the vertical, a 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.

Inspection and retirement

तालिका 5 — What ends a net’s service life
जाँच गर्नुहोस् Retire or repair if
Corner loops and their stitching A loop is deformed, the stitching is broken, or the band is cut at the throat
सीमा The border is cut, flattened, or has pulled out of a corner
Load-bearing bands Any band is cut, गहिरो खारेज, heat glazed or chemically stained
Mesh geometry The lattice is distorted from an overload — the net no longer sits square
सिलाई Stitch lines are broken or pulled at a crossover
Label and printing The WLL or the arrangement is illegible — an unlabelled net cannot be rated

Inspect before each lift and have the net examined by a competent person at the interval your site sets. यसलाई सफा र सुक्खा भण्डार गर्नुहोस्, जमिनबाट र प्रत्यक्ष सूर्यबाट बाहिर; never knot, weld or heat-repair a webbing net.

Steel coils loaded inside a webbing cargo net on a factory floor
Coils inside the mesh: at this rating the net is as much a handling tool as a container, and the crane never touches the cargo.

How it is built, and how the rating is proven

  • Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
  • Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
  • Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
  • Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.

The same works weaves webbing and presses wire rope ferrules, which is why a net, a webbing गोफन र ए तार डोरी गोफन on the same lift can be matched in rating rather than bought from three suppliers.

जहाँ क 20 t net does the work

तालिका 6 — Sectors that buy this class
क्षेत्र नेटले के उठाउँछ सामान्य निर्माण
इस्पात र निर्माण बन्डलहरू, खण्डहरू, stillage loads समतल नेट, 100 मिमी डुप्लेक्स, eight points
ढुङ्गा र खदान ब्लकहरू, विभाजित ढुङ्गा, cobbles झोला फारम, 150 मिमी जाल, corner patches
पोर्ट र टर्मिनलहरू Bagged and unitised cargo, quay work Flat net on a spreader, मुद्रित WLL
काठ Sawn packs, पोलहरू, sleepers Flat or bag, 150 - 200 मिमी जाल
स्क्र्याप र रिसाइक्लिंग मिश्रित र घर्षण स्क्रैप Large mesh, wear bands at the corners
Precast concrete Units, घण्टी, प्यानलहरू Flat net with edge sleeves, eight points

बारम्बार सोधिने

छ 20 t rating for the net or for the whole assembly?

The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, बाँधहरू, spreader and slings above must be rated at least 20 t as well.

Why is the safety factor 7:1 र होइन 5:1?

7:1 is the factor we build to for this class, which gives a 140 t न्यूनतम ब्रेकिङ लोड a को लागि 20 टी मूल्याङ्कन. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.

Polyester or nylon for a 20 t लिफ्ट?

Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.

How big a net do I need for a 2 × 2 m load?

At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.

Can it be lifted by a single hook?

Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.

Can you print our brand and the WLL on the net?

Yes — WLL, arrangement, शुद्ध आकार, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.

उद्धरण अनुरोध गर्नुहोस्

Send the load and how it is presented

The cargo — what it is, यो कसरी प्याक गरिएको छ, and the weight as presented for the lift;

The footprint — length × width, plus height if a bag form is needed;

The lift — four or eight points, हुक उचाइ, and whether a spreader beam is available;

The duty — how many lifts a week, indoors or on a quay, and the temperature range;

The paperwork — CE marking, test report and own-brand printing if you need them.

Send the load and the footprint for a quotation →

अब कहाँ जाने हो

लिफ्ट स्लिङ रिगिङ कम्पनी · Lifute Industrial Park, Taizhou शहर, जियाङसु प्रान्त, चीन · HS कोड 630790
टेलिफोन +86 523 8693 5818 व्हाट्सएप +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

आफ्नो सन्देश छोड्नुहोस्

शीर्षमा स्क्रोल गर्नुहोस्