ထုတ်ကုန်အမျိုးအစားများ

5 Ton Heavy Duty Ratchet Straps

အတိုချုံးဖော်ပြချက်:

Lift sling အကြံအဖန်ထုတ်လုပ်သည့်ကုမ္ပဏီ 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

5 ton heavy duty ratchet straps: 50 မီလီမီတာ polyester, 5,000 daN break, LC 2,500 daN မှ EN 12195-2. Stainless 304/316 and aramid high-temp builds. Factory-direct.

ထုတ်ကုန်အသေးစိတ်

Lift sling အကြံအဖန်ထုတ်လုပ်သည့်ကုမ္ပဏီ 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

Cargo restraint · EN 12195-2

5 Ton Heavy Duty Ratchet Straps

50 mm polyester webbing, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

2,500 နှင့် lashing စွမ်းရည် 5,000 နှင့် ခွန်အားကိုချိုးဖျက် 350 နှင့် STF at 50 daN hand 3-၁၀ မီတာ standard length
5 ton heavy duty ratchet straps with hook options: claw hook, အပြားချိတ်, D ring and S hook

“5 ton heavy duty ratchet straps” is the phrase buyers search for, and the reason this page exists is that the phrase covers two different articles. ဂရန် 50 mm polyester assembly the breaking strength is 5,000 နှင့် နှင့် lashing စွမ်းရည် (LC) သည် 2,500 နှင့်. Both numbers are real, both are printed on the same label, and quoting one against the other is how trailers get overloaded. We build the assembly to EN 12195-2, mark it, and state both figures so the comparison you make at quotation stage is between like and like.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 ရန် 10 m စံအဖြစ်, LC 2,500 နှင့်, STF 350 နှင့် N မှာ 50 နှင့် လက်တွန်းအား. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.

Part of the webbing လောက်လွှဲ and lashing range. ဟိ 50 mm specification in isolation sits on the 50 မီလီမီတာ 5000 ကီလိုဂရမ် ratchet lashing ခါးပတ် စာမျက်နှာ.

What “5 Ton” Actually Means on a Ratchet Strap

Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. EN အောက်တွင် 12195-2 ကြိမ်ကြိုးကြိုး၏ ကြိုးသည် ၎င်း၏ ကြိမ်ဒဏ်ခံနိုင်မှု အနည်းဆုံး နှစ်ဆအထိ ရှိရပါမည်။, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.

စားပွဲ 1 — The three numbers on a 5 ton heavy duty ratchet strap
ပုံ Value on the 50 mm assembly ဘာကိုဖော်ပြတာလဲ။ How it gets misread
အနိမ့်ဆုံး ချိုးဖျက်နိုင်စွမ်း 5,000 နှင့် (5,000 ကီလိုဂရမ်) ဆွဲချစမ်းသပ်မှုတစ်ခုတွင် တပ်ဆင်မှုပျက်ကွက်သည့်ဝန် Read as the working figure — the mistake that overloads a trailer
ကြိမ်ဒဏ်ပေးနိုင်စွမ်း (LC) 2,500 နှင့် (2.5 t) စည်းဝေးပွဲကျင်းပရန် အဆင့်သတ်မှတ်ထားသည်။, printed on the label lifting sling ၏ WLL နှင့် နှိုင်းယှဉ်သည်။, which is a different duty altogether
စံနှုန်းတင်းမာမှု (STF) 350 နှင့် N မှာ 50 နှင့် လက်တွန်းအား The tension one person reaches with the ratchet handle LC နဲ့ ရှုပ်နေတယ်။, ထို့ကြောင့် အော်ပရေတာသည် အသုံးဝင်သော အမှတ်ကို ကျော်လွန်နေပါသည်။
Ask for both numbers. Two suppliers quoting “5 tonne” can be quoting the breaking strength and the working figure — a factor of two apart — and a North American catalogue printing the same article as “10,000 lb” is quoting breaking strength in pounds. ခါးပတ်အတူတူ, different unit, same trap.

Why the 50 mm Build Is the Heavy-Duty Default

Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. ဟိ 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.

စားပွဲ 2 — Width ladder: where 50 mm sits
ဝဘ်အကျယ် Typical LC ခွန်အားကို ချိုးဖျက်ခြင်း။ What it is bought for
25 မီလီမီတာ (1 ၌) 400–500 daN 800–1,000 daN Tool boxes, light restraint, tight anchor eyes
35 မီလီမီတာ (1-3/8 ၌) 750 နှင့် 1,500 နှင့် Van and trailer decks, general cargo
38 မီလီမီတာ (1-1/2 ၌) 1,000–1,500 daN 2,000–3,000 daN စတီးပြား, ပိုက်ထုပ်များ, plant
50 မီလီမီတာ (2 ၌) 2,500 နှင့် 5,000 နှင့် Heavy cargo restraint, ကွိုင်, စက်ယန္တရား, ကွန်တိန်နာများ
75-100 မီလီမီတာ 5,000 daN and up 10,000 daN and up Abnormal loads, where the bed allows the width

The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.

Standard Specification of the 5 Ton Assembly

စားပွဲ 3 — 50 မီလီမီတာ 5 ton heavy duty ratchet strap: နည်းပညာဆိုင်ရာဘောင်များ
ကုသိုလ်ကံ သတ်မှတ်ချက်
Webbing 100% ခံနိုင်ရည်မြင့်မားသော polyester, twill ရက်ကန်း, UV သည် တည်ငြိမ်သည်။, 50 mm ± 2%
တီးဝိုင်းအထူ / အစုလိုက်အပြုံလိုက် 1.8 mm အမည်ခံ / 88 g per metre
ကြိမ်ဒဏ်ပေးနိုင်စွမ်း (LC) 2,500 အသင်းတော်အလိုက်၊
အနိမ့်ဆုံး ချိုးဖျက်နိုင်စွမ်း 5,000 နှင့် (2:1 against LC)
စံနှုန်းတင်းမာမှု (STF) 350 နှင့် N မှာ 50 နှင့် လက်တွန်းအား
တင်းမာမှု Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle
LC တွင် ရှည်သည်။ 7% သို့မဟုတ် နည်းသည်။
ဝန်ဆောင်မှုအပူချိန် −40°C မှ +100 °C (polyester webbing)
စံအရှည် 3-၁၀ မီတာ; 1–30 m to order
အမှတ်အသားပြုခြင်း။ ယက်တံဆိပ်: LC, STF, အရှည်, သုတ်နံပါတ်, standard reference
စံ Designed, tested and marked to EN 12195-2
HS ကုဒ် 630790

The End Fitting Decides Whether the Strap Fits the Job

The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.

စားပွဲ 4 — End fittings for 5 ton heavy duty ratchet straps
လျောက်ပတ်တယ်။ Anchors to Notes before ordering
Chassis rave hook Flatbed side rail, chassis lip Check rail thickness and that the hook throat clears it
Claw hook Anchor rings, D rings, recessed eyes Opening must clear the ring; load on the crown only
D ring / မြစ်ဝကျွန်းပေါ်လက်စွပ် Welded or bolted anchor points Ring bore at least as wide as the webbing
Flat snap hook အီး တစ်ပုဒ်, slotted rail, တွင်းများ Confirm slot width; snap gate must close fully
S hook ပိုက်များ, သံလမ်း, frame members Both ends must seat without point loading on a weld
Sewn loop / looped ends Around the load or through a bore Nothing metal at the load; ideal for finished surfaces
အဆုံးမဲ့, လျောက်ပတ်ခြင်းမရှိ Girth only — hulls, ကွိုင်, အစုအဝေးများ See the endless loop build below
5 ton heavy duty ratchet straps with hook options: claw hook, အပြားချိတ်, D ring and S hook
တစ်မျိုး 50 mm တီးဝိုင်း, eight ways to terminate it — the hook option decides which anchor the strap can reach.

ဟိ 5 Ton Strap in Two Special Builds

Polyester covers most freight, and it fails predictably when it is out of its depth: ပျော့ပျောင်းသည်။ 150 °C and melts at about 255 °C, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.

Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces

The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 သို့မဟုတ် 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 နှင့် N မှာ 25 mm to 2,500 နှင့် N မှာ 50 မီလီမီတာ, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.

The grade decision is about chloride, မတင်ပါ။. 304 (1.4301) handles rain, ရေချို, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 ပိုခိုင်ခံ့တယ်ဆိုတဲ့ ယုံကြည်ချက်က မှားယွင်းတဲ့ပိုင်ဆိုင်မှုအတွက် ပေးဆပ်ခြင်းပါပဲ။. အပလီကေးရှင်းသည် ဘေးကင်းရေးနှင့် ပတ်သက်သည့်နေရာ, ပြေစာဖော်ပြချက်တွင်မဟုတ်ဘဲ ကြိတ်လက်မှတ်ရှိ အဆင့်ကို အတည်ပြုပါ။.

Two shop-floor notes worth passing on. Stainless threads ဆေးခါး, so a dry 316 nut သည် ခဲတစ်လုံးပေါ်သို့ ပြေးသည်။ 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. ဆားရေတွင် အလူမီနီယံဖြင့် ပါသော stainless bolt သည် galvanic pair တစ်ခုဖြစ်သည်။, so where the strap anchors to an alloy frame, အဆက်အသွယ်ကိုခွဲထုတ်ပါ။.

Full range and grade comparison: အဆုံးမဲ့ stainless steel ratchet လက်ပတ်ကြိုး.

အာရမစ် (Kevlar) ratchet straps — for heat, sparks and cut edges

Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 °C. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.

The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.

Two honest limits. Aramid is flame retardant, not fireproof: molten steel, ladles and hot slag still need a heat shield or a stand-off. And low elongation is exactly wrong for snatch and shock loads — for those, the polyester band or a dedicated recovery strap is the right article.

Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.

How Many Straps Does the Load Actually Need?

Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.

စားပွဲ 5 — Worked example: 50 mm straps at 2,500 daN LC
Straps used Angle to the deck Restraint per strap Total restraint
2 45ံ အနီးစပ်ဆုံး. 1,750 နှင့် အနီးစပ်ဆုံး. 3,500 နှင့်
4 30ံ အနီးစပ်ဆုံး. 1,250 နှင့် အနီးစပ်ဆုံး. 5,000 နှင့်
4 45ံ အနီးစပ်ဆုံး. 1,750 နှင့် အနီးစပ်ဆုံး. 7,000 နှင့်
4 60ံ အနီးစပ်ဆုံး. 2,165 နှင့် အနီးစပ်ဆုံး. 8,660 နှင့်
6 45ံ အနီးစပ်ဆုံး. 1,750 နှင့် အနီးစပ်ဆုံး. 10,500 နှင့်

The arithmetic is an illustration, not a lashing plan: IN 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.

ဘယ်မှာလဲ။ 5 Ton Ratchet Strap Earns Its Keep

  • Flatbed, container and plant trailer restraint — the volume application for the 50 mm build.
  • စတီးကွိုင်, slab, billet and pipe bundles, with edge protection at the contact points.
  • စက်ယန္တရား, moulds and skid-mounted plant, ဘယ်မှာလဲ။ 25 mm strap has neither the width nor the tension.
  • သစ်ထုပ်များ, သေတ္တာများနှင့် သေတ္တာများ, including the endless form that simply closes round the pack.
  • Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
  • ရေကြောင်း, marina and wash-down duty in 304 သို့မဟုတ် 316 where plated hardware would be a maintenance item.
  • Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.
5 ton heavy duty ratchet straps securing a timber crate on a flatbed truck
50 mm straps over a timber crate on a flatbed — two legs at roughly 45°, hooks seated on the crown of the rail.

အရောင်, Printing and Private Label

Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, လိမ္မော်သီး, အဝါရောင်, အနက်ရောင်, အနီရောင်, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, အရှည်, standard and traceability code. Cartons of 10 ရန် 20 အပိုင်းပိုင်း, palletised for export, with neutral or own-brand packaging as required.

စမ်းသပ်ခြင်း။, Traceability and the Paperwork Buyers Ask For

Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. စမ်းသပ်အစီရင်ခံစာများ, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.

One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.

အမေးများသောမေးခွန်းများ

ကတစ် 5 ton ratchet strap rated to lift 5 တန်?

မရှိ, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.

Why does the same strap get called 5 တစ်တန်နှင့် 2.5 တစ်တန်?

Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.

50 မီလီမီတာ သို့မဟုတ် 38 mm for a flatbed?

50 မီလီမီတာ, unless the anchor points are small. ဟိ 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; အဆိုပါ 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.

Do I need 304 သို့မဟုတ် 316 stainless?

316 where chloride is present — sea air, ဆားဖြန်း, de-icing ဆား, boatyards, အစာအပင်များ. 304 is enough for rain, ရေချို, condensation and indoor wash-down. The difference is corrosion resistance, အင်အားတော့ မဟုတ်ဘူး။.

At what temperature does polyester fail, and what does aramid do instead?

Polyester softens around 150 °C and melts at about 255 °C, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 °C, and chars at about 427 °C instead of melting. အပေါ်က 400 °C, or against molten metal, both need a heat shield.

Can the strap be supplied with a printed brand and a custom length?

ဟုတ်ကဲ့. အကျယ်, အရှည် 30 ဍ, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.

Quotation တစ်ခုတောင်းဆိုပါ။

Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, ပတ်ဝန်းကျင် (salt, အပူ, ရေဆေးချပါ။), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.

Lift Sling Rigging ကုမ္ပဏီ

Lifute စက်မှုပန်းခြံ, Taizhou မြို့, Jiangsu ပြည်နယ်, တရုတ်

Tel: +86 523 8693 5818 · WhatsApp: +86 180 6600 2268

အီးမေး: 702461526@qq.com · HS code 630790

Send your lifting details for a quotation →

ဆက်စပ်ထုတ်ကုန်များ

Lift Sling Rigging ကုမ္ပဏီ · Lifute Industrial Park, Taizhou မြို့, Jiangsu ပြည်နယ်, တရုတ် · HS ကုဒ် 630790
Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com · xulft.com

 

သင့်စာတိုကို ချန်ထားပါ။

ထိပ်သို့ ရွှေ့ပါ။