Kategoriji tal-Prodotti

Steel Pipe Lifting One Way Webbing Sling

Deskrizzjoni Qasira:

Lift sling rigging company produce Steel Pipe Lifting One Way Webbing Sling,Lifting Slings For Steel and Steel Tube.

One-way webbing sling for steel pipe and tube: 25-300 mm poliester, 1-24 t, għajn u għajn jew bla tarf, cut to your pick spacing. Printed to your reference.

Dettall tal-Prodott

Lift sling rigging company produce Steel Pipe Lifting One Way Webbing Sling,Lifting Slings For Steel and Steel Tube.

One-way sling · eye and eye · steel pipe and tube

Steel Pipe Lifting One Way Webbing Sling

Żewġ għajnejn, żewġ fisien, one journey — a flat woven band cut to the pick spacing of the lift and printed with the tonnage it will carry.

1–24 t Firxa WLL 25–300 mm wisa 'faxxa ×1.4 two legs to 45° ±2 % length tolerance
steel pipe lifting one way webbing sling carrying a galvanised pipe bundle

This is the eye-and-eye form of the one-way sling, and it is the form that suits most steel pipe and tube consignments: a flat polyester band with a formed eye at each end, one eye on each hook, the band bearing under the pipe or round the bundle. It is bought against a consignment rather than issued from a sling store, and it goes with the load instead of coming back. Working load limits run from 1 t biex 24 t, wisgħat tal-faxxa minn 25 mm biex 300 mm, u tulijiet minn 0.5 m biex 100 m, at a factor of 5:1, 6:1 jew 7:1.

Quick answer: for pipe the sling is specified by the pick positions. The length is the distance from the hook down to each pick, the capacity is set by the angle the legs make with the vertical, and the width is set by what the pipe surface will tolerate. Tonnage alone does not describe the article.

Żewġ għajnejn, żewġ fisien, and what that decides

The same one-way discipline is sold in three shapes, and the shape is decided by what is at each end of the band. On pipe work the eye-and-eye form is the general answer because a pipe is usually picked at two points along its length, with something to hook to above each one.

Tabella 1 — The three shapes a one-way sling is bought in, for pipe work
Shape What is at each end How the pipe is held When it is the right buy
Eye and eye — this page A formed flat eye, stitched and bar-tacked One eye on each hook, band under the pipe or round the bundle Two picks along the length, with a hook, pin or shackle above each
Loop bla tarf Nothing — a closed ring Wrapped round the pipe and back through itself, or doubled as a basket Where there is no fitting to thread and the band must close on itself
għajn waħda One eye and a plain tail Fgat: the tail passes back through the eye and the noose closes Where the pipe must be gripped rather than hung, or left slung on arrival

The single-eye version is written up separately, because a choke changes both the arithmetic and the length: ara bragi tal-irfigħ bla tmiem mod wieħed, għajn waħda, for steel pipe and tubing. The endless loop is for the same loads with no hardware at either end — il-forma taċ-ċirku magħluq is on its own page as well. Nothing prevents a consignment using more than one shape, but each has to be specified and counted separately.

The figure on the band is per leg — the angle decides what a pair will carry

A two-leg lift is never twice one sling. The legs lean towards each other, so each leg carries more than half the load and the pair carries less than two bands’ worth. The design factor table used for synthetic webbing slings states it plainly, and the reference angle is measured from the vertical, not between the legs.

Tabella 2 — Mode factor by arrangement, and what a 5 t sling becomes
Arranġament Angolu Fattur Kapaċità
Sieq waħda, vertikali — × 1.0 5,000 kg
Żewġ saqajn 0–45° mill-vertikali × 1.4 7,000 kg per pair
Żewġ saqajn 45–60° mill-vertikali × 1.0 5,000 kg per pair
Żewġ saqajn beyond 60° not permitted —
Basket, both parts vertical 0° × 2.0 10,000 kg
Basket, parts at 45–60° — × 1.4 7,000 kg
Fgat — × 0.8 4,000 kg

Worked case. A 9 t joint of 508 mm pipe, picked at two points, ganċ 4 m above the pipe, pick spacing 6 m. Each leg is √(3² + 4²) = 5.0 m long and makes 36.9° with the vertical, so the pair is worth 1.4 × WLL. To carry 9 t the slings must be rated 9 ÷ 1.4 = 6.4 t each, u a 7 t band is the answer. Halve the hook height and the same pipe needs 9 t bands — the pipe did not change, the geometry did.

steel pipe suspended on two one way webbing slings in a workshop
Żewġ saqajn, one pick near each end: the arrangement this page is written around.

Where the picks go on a pipe

Pajp huwa raġġ, and where it is supported decides whether it sags, whips or bends at the overhang. The classical layout for a uniform span puts the supports at about 0.21 L from each end, which makes the sag in the middle equal to the overhang at the ends; many yards simply use the quarter points, which is close enough on a stiff wall and easier to measure. Neither figure is a rule from a standard — it is a layout, and the layout is what the sling length is cut to.

Tabella 3 — Pick layout by joint length (single joint, żewġ fisien)
Pipe length Pick position from each end Span between picks Noti
Sa 6 m 1.5 m (quarter points) 3 m Żewġ fisien, one hook or two
6 – 12 m 0.21 L, jew 2 m minimu 0.58 L The usual range for line pipe
12 – 18 m 0.21 L 0.58 L Four picks or a spreader above
Fuq 18 m Two pick groups — Spreader beam rather than a long V
Gzuz One pick per sling position Set by the pack Girth, not length, sets the band
pick positions marked on a coated steel pipe before lifting
The pick positions marked on the pipe itself: the only instruction that still exists at the far end of the journey.

Two practical points that decide more lifts than the table does. A pick must not sit on a weld seam or a coating repair, and it must clear the end collar: an end that is thicker than the barrel will take the band on its shoulder and cut it. On a joint with a bevelled or sheared end, the band goes behind the bevel, never on it.

webbing sling in a basket hitch around a bundle of steel tubing
A basket hitch on tube: two parts of the band share the load, provided both are vertical. Lean them and the pair stops being worth twice one.

Length from pick spacing and hook height

On a two-leg lift the band is not a height, it is a hypotenuse. Given the spacing between the picks and the height of the hook above the pipe, the leg length and the angle follow directly — and the angle, mhux it-tunnellaġġ, is what changes the capacity of the pair.

Leg length = √((spacing ÷ 2)² + hook height²), u angle from vertical = arctan((spacing ÷ 2) ÷ hook height). Add the eye take-up at both ends — roughly the eye clear length — and order to the next half metre. A sewn article holds ±2 % on length.

Tabella 4 — Leg length and capacity for a pair of 5 t bragi
Pick spacing Hook height Leg length Angle from vertical Pair capacity
4 m 4 m 4.47 m 26.6° 7,000 kg
6 m 4 m 5.00 m 36.9° 7,000 kg
8 m 5 m 6.40 m 38.7° 7,000 kg
10 m 4 m 6.40 m 51.3° 5,000 kg
12 m 5 m 7.81 m 50.2° 5,000 kg
12 m 7 m 9.22 m 40.6° 7,000 kg
16 m 6 m 10.00 m 53.1° 5,000 kg
16 m 9 m 12.04 m 41.6° 7,000 kg

The capacity column is the pair, not the leg, and it already includes the mode factor. Beyond 60° from vertical the arrangement is outside the factor table: raise the hook or shorten the spacing rather than adding tonnage.

This is why the same pipe can need two very different bands on two sites. A yard with a high gantry picks a 12 m joint with 5 t legs; a shed with low headroom, picking the same joint at the same spacing, needs 7 t legs or a spreader to lift the pick points clear of the hook. The sling is the same length in both cases and a different article.

What the band bears on: ħajt, coating and the end

The width of the band is chosen by the surface it touches, mhux bit-tunnellaġġ. A pipe is a line contact with a curved, sometimes thin, sometimes coated face — and the failure on pipe work is nearly always local: a cut, a scuff or an ovalised wall at the pick, not a band that broke in the middle.

Tabella 5 — Width and protection by pipe surface
Pajp Wisa 'tal-medda Protection at the pick Dak li jmur ħażin mingħajru
Bare black pipe, ħajt 6 mm and up 75 – 100 mm None normally needed Cosmetic scuffing only
Bare pipe, wall under 4 mm 100 – 150 mm Faxxa wiesgħa, pick behind the collar Ovalisation at the pick
Miksija, painted or lined 150 mm, 7.5 faxxa mm Ilbes kmiem, kuntatt artab Coating damage becomes a rejection
Galvanised tube 100 – 150 mm Sleeve where the band turns Bright witness marks on the zinc
Bundled tube 150 – 200 mm Sleeve at the arris, if square-cut Band cut on a tube end
Stainless or aluminium 150 mm, sleeve as standard kmiem, and a band that has never been used on steel Iron transfer, then corrosion

Two details cost almost nothing at the order and are impossible to add later: a wear sleeve over the contact point, which is replaced with the band instead of the band being replaced, u a għajn rinfurzata where a hook or shackle pin bears. On a one-trip article both are thrown away with the band, which is exactly why they are cheap.

pair of one way webbing slings with flat eyes for pipe lifting
Għajn u għajn, minsuġa ċatta: l-għajn hija l-faxxa mitwija lura u meħjuta, so the hook bears on a soft flat loop rather than on an edge.
white polyester webbing sling with reinforced red eye
A reinforced eye in a sleeve where the hook bears. On pipe work it is the eye that wears first, mhux il-banda.

Speċifikazzjoni

Tabella 6 — Eye-and-eye one-way sling, speċifikazzjoni standard
Parametru Bini standard Noti
Istrixxi Flat woven high-tenacity polyester, 25–300 mm 4 mm jew 7.5 faxxa mm
Limitu tat-tagħbija tax-xogħol 1 t – 24 t kull braga Vertikali, sieq waħda
Fattur tad-disinn 5:1 / 6:1 / 7:1 Same WLL needs a wider band at 7:1
Tispiċċa Formed flat eye at each end Stitched and bar-tacked; sleeved on request
Eye clear length 250 mm at 1 t biex 650 mm at 15 t Hook bowl or pin plus about 10 mm
Tul 0.5 m – 100 m Cut to the pick spacing; ±2 %
Kulur Biex tordna; IN 1492-1 code up to 10 t A second channel for sorting
Temperatura −40 °C sa +100 °C Poliester; not for molten metal
Immarkar WLL, tul, fibra, lott, your reference Printed on the band and on a sewn label
Ippakkjar Coiled, baled or cartoned Can travel inside the consignment
Kodiċi HS 630790 Packing list line

The standard range

The works weaves nine tonnages on a 4 mm band u disa fuq a 7.5 faxxa mm. Width follows the tonnage and the factor, and the minimum length steps up with the width rather than with the tonnage — which is the line that decides a short order.

Tabella 7 — Width by WLL and factor, with minimum length
WLL Banda 5:1 6:1 7:1 Min. tul
1 t 4 mm 25 mm 50 mm 30 mm 0.5 m
2 t 4 mm 50 mm 100 mm 60 mm 1.0 m
3 t 4 mm 75 mm 150 mm 90 mm 1.0 m
4 t 4 mm 100 mm 200 mm 120 mm 1.5 m
5 t 4 mm 125 mm 250 mm 150 mm 1.5 m
6 t 4 mm 150 mm 300 mm 180 mm 1.5 m
8 t 4 mm 200 mm 200 mm 240 mm 2.0 m
10 t 4 mm 250 mm 250 mm 300 mm 2.0 m
12 t 4 mm 300 mm 300 mm 300 mm 2.0 m
2 t 7.5 mm 25 mm 50 mm 30 mm 0.5 m
4 t 7.5 mm 50 mm 100 mm 60 mm 1.0 m
6 t 7.5 mm 75 mm 150 mm 90 mm 1.0 m
8 t 7.5 mm 100 mm 200 mm 120 mm 1.5 m
10 t 7.5 mm 125 mm 250 mm 150 mm 1.5 m
12 t 7.5 mm 150 mm 300 mm 180 mm 1.5 m
16 t 7.5 mm 200 mm 200 mm 240 mm 2.0 m
20 t 7.5 mm 250 mm 250 mm 300 mm 2.0 m
24 t 7.5 mm 300 mm 300 mm 300 mm 2.0 m

Two lines of reading are worth doing before the table is used. The two blocks share the same width ladder, so a band bought thicker for a delicate surface buys nothing if the width column was already right — thickness is for tonnage and wear, width is for the surface. And at 8 t and above the 6:1 column runs out of width: from that point the band is already at 300 mm, and the answer to more tonnage is a heavier block or two slings, not a wider band.

Mod wieħed, and what that adds to the order

The band travels with the pipe, is inspected once at issue, and is not recovered. That changes three things about how it is ordered, and none of them about how it is made.

  • Counted per pick, għal kull pakkett. A bundle on two picks is two bands; a long joint on four picks is four. Add 2–5 % for the band that gets cut while the pack is made up, and put the number on the order rather than in someone’s head.
  • Marked to the consignment. Limitu tat-tagħbija tax-xogħol, length and your reference printed on the band — pack number, order number or part number — because that print is the only record the receiving site will have. Il- one way sling category sets out the discipline in full.
  • Packed to arrive with the goods. Coiled and baled, cartoned, or packed into the crate beside the pipe so the bands land at the same time as the consignment instead of a week earlier.

L-ispezzjoni inkwistjoni

There is one inspection in the life of a one-way band and it happens before the lift. Four places, f'din l-ordni:

  • The eyes. Ħjata, bar-tacks and the mouth of each eye — a broken stitch at an eye gives no warning at the load.
  • The band where it will bear. Qatgħat, snags, ħġieġ mis-sħana, and any thin patch that shows daylight through the weave.
  • The print. If the WLL or the length cannot be read, the band cannot be matched to the pipe it was cut for.
  • Dak li ilha tinsab fiha. Naqal, swaf u żejt jivvjaġġaw fil-kuntatt; a clean band is the only protection on the list that costs nothing.

Mistoqsija ta' spiss

How many slings does a 12 m joint of pipe need?

Żewġ, at about 0.21 L from each end — 2.5 m in from either end, leaving a 7 m span — provided the wall carries the overhang. Fuq madwar 18 m, or where the overhang whips, four picks or a spreader beam is the honest answer and the band count goes up with it.

Can one sling lift one end of a pipe?

Only for a short, iebes, light joint, and then it is a single vertical leg at 1.0 × WLL with the pipe hanging at an angle. On anything long the pipe rotates about the pick and the load walks; two picks are the arrangement, and the second sling is cheaper than the first accident.

Għajn u għajn, endless loop or single eye for pipe?

Eye and eye where there is a hook or a pin at each pick — the usual case. The endless loop where nothing must be threaded and the band closes on itself, which is also the kindest to a coated surface. The single eye where the pipe must be gripped in a choke and left slung on arrival. The three are separate articles and are counted separately.

How flat is too flat?

Beyond 60° from the vertical the two-leg arrangement leaves the factor table entirely, and the tension in each leg climbs steeply for very little gain in height. If the pick spacing is fixed and the headroom is not there, the answer is a spreader beam that lifts the pick points instead of a heavier pair of slings.

Will the sling mark galvanised or coated pipe?

A used band can: grit embedded in the weave polishes the zinc, and a band that has carried black steel leaves iron behind that shows up as rust later. A sleeve at the contact point, a band kept for coated work only, u 150 mm of width instead of 75 mm are the three measures that prevent it.

Can the length be cut to my pick spacing exactly?

Yes — that is what the length on the order means. Send the spacing between picks and the height of the hook above the pipe, and the leg length comes out of the arithmetic in Table 4; add the eye take-up and round to the next half metre. The finished length is confirmed in writing before the bands are cut, to ±2 %.

Send the lift, mhux biss it-tunnellaġġ

Six lines and the band can be cut

Il-pajp: dijametru ta 'barra, ħxuna tal-ħajt, coating or finish, and whether it travels as a joint or a bundle;

The mass of one lift, and how many picks you intend to use;

The spacing between picks, and the height of the hook above the pipe;

The fittings at each pick — hook, shackle or pin — with their sizes;

The factor your market expects: 5:1, 6:1 jew 7:1;

Ir-referenza għall-istampar, il-kulur, u l-kwantità għal kull pakkett.

Send the pipe and the pick spacing for a quotation →

Lift Sling Rigging Co., Ltd · Lifute Industrial Park, Belt Taizhou, Provinċja ta 'Jiangsu, Iċ-Ċina · Kodiċi HS 630790 · Tel / WeChat +86 180 6600 2268 · 702461526@qq.com

Fejn tmur jmiss

Lift Sling Rigging Company · Lifute Industrial Park, Belt Taizhou, Provinċja ta 'Jiangsu, Iċ-Ċina · Kodiċi HS 630790
Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com · xulft.com

 

Ħalli l-Messaġġ Tiegħek

Skrollja għal Fuq