Lift sling rigging company produce One-Way Webbing Sling,One Way Endless Webbing Slings,Polyester Single Trip One Way endless webbing slings.
One Way Webbing Sling
ກ sling webbing ທາງດຽວ is a rated polyester sling bought for one journey: it is fitted to the load, travels with it and is written off against that job instead of being returned to a sling store. This page covers the closed loop ທີ່ບໍ່ມີທີ່ສິ້ນສຸດ form — the shape specified for pipe, tube and bundling work, because a loop wraps a cylinder instead of hooking it. ຊ່ວງມາດຕະຖານ: 1 t ເຖິງ 12 t, ຄວາມກວ້າງຂອງແຖບ 25 mm ເຖິງ 300 ມມ, ປັດໄຈຄວາມປອດໄພ 5:1, 6:1 ຫຼື 7:1, ຄວາມຍາວຂອງວົງ 0.5 m ກັບ 100 ມ, marked to BS EN 1492-1.
On this page
What “one way” decides, ແລະສິ່ງທີ່ມັນບໍ່ໄດ້
The phrase describes the commercial life of the article, not its quality. A one way sling is manufactured, ໂຫຼດຫຼັກຖານແລ້ວ, colour coded and labelled to the same standard as a sling that will be inspected for years; the difference is that it leaves the store once and does not come back.
Three practical consequences follow. ມັນແມ່ນ issued with the load, so it becomes a line on the packing list rather than an item in a sling register. ມັນແມ່ນ inspected once, at the point of issue, while a fault can still be replaced from the same consignment. And its print is its whole record: ຈໍາກັດການໂຫຼດເຮັດວຽກ, ຄວາມຍາວ, factor and batch are the only traceability the band will ever carry, so the marking has to survive a lorry, a container and a loading bay — not just the production line.
What it does not change is the engineering. A narrow band or a lower factor chosen because “it is only going one way” is not a saving; ມັນເປັນຂອບທີ່ບໍ່ໄດ້ຈັດອັນດັບທີ່ເອົາອອກຈາກການຍົກ. The figure that applies is the figure printed on the band, for the arrangement actually used. Buyers who need the returnable version of the same loop should read the single ply endless flat sling page instead.
Why a closed loop is the right form for pipe, tube and bundles
An endless webbing sling is a band joined to itself. There is no eye to line up against a machined pipe end, no stitching stack at the bearing point and no shackle, hook or thimble anywhere on the article. On round loads that single property does most of the work.
- It cannot mark a coating. Galvanising, fusion bonded epoxy, three layer PE and paint are all damaged by the same things: a steel edge, a sliding hook and point pressure. A woven polyester face addresses all three. Nothing metallic contacts the pipe, and the load never slides against a fitting.
- The choke holds itself. Passed round the pipe and back through the loop, the band tightens as the load rises. On a cylinder the contact line is a full wrap rather than two point contacts, which is why a loop resists slipping along the axis and does not walk towards the pipe end during a pick.
- The load stays centred. Because the band wraps symmetrically, the pick point sits over the centre of gravity of a joint or bundle rather than off one side — the usual cause of a tilted, eccentric lift and of one sling taking more than its share.
- Pressure is spread by width. Thin wall PVC, PE and stainless tube dent under a narrow band. A 100–200 mm face turns a point load into a low pressure band, which is the single most effective protection on a soft or thin walled pipe.
- Nothing to lose and nothing to thread. A band with end fittings can arrive with the fittings gone. A loop is one piece of webbing: it is either there or it is not, and the person re-slinging at the far end needs no rigging plan to use it.
Where a one way webbing sling is used
The loop is chosen where the load is ຫໍ່ rather than hooked, and where the surface matters as much as the tonnage. On a joint lifted on its own, one loop goes round the pipe near each end and the two legs meet at the hook; on a bundle, one loop per pick position is choked round the pack. The applications below are the ones this range is most often bought for, and each one puts a different line on the enquiry.
| ໂຫຼດ | Why the loop suits it | What to state on the order |
|---|---|---|
| Steel pipe and tube, single joints or bundles | A round section is wrapped, not hooked; the choke grips and the band cannot slide along the pipe. | ເສັ້ນຜ່າສູນກາງນອກ, ຝາ, joint mass or bundle mass, spacing of the two pick positions. |
| PVC and PE pipe | Thin walls dent under point pressure; a wide soft face spreads the load and leaves no witness mark. | ເສັ້ນຜ່າສູນກາງ, wall thickness, mass per joint, whether a surface mark is a rejection. |
| Anti-corrosion pipe (3PE, FBE, tape wrap) | No metal and no sliding contact, so the coating survives the lift and the inspection at destination. | Coating type, whether coated ends are handled, and any requirement for a sleeve. |
| Stainless and copper tube | ອ່ອນ, expensive and unforgiving of a burr; a polyester face is softer than the load. | ຈົບ (mill, polished), ເສັ້ນຜ່າສູນກາງຂອງທໍ່, girth at each pick. |
| Rebar bundles and steel mesh | Cut wire and mesh edges attack a narrow band; a wide loop carries the bundle and resists abrasion. | Bundle mass, number of ties per bundle, whether edge sleeves are needed. |
| Profiles, sections and sheet packs | A sharp arris is a blade against webbing; width and edge protection decide the life of the band. | ພາກ, ຄວາມສູງ stack, ສະພາບຂອບ, band direction. |
| ບັນທຶກ, timber and timber packs | The arris prints into dressed stock and cuts the weave on a narrow band; a loop spreads the pressure. | Pack mass as it travels, girth at the picks, whether a compression mark matters. |
| Machinery and painted assemblies | Nothing metallic touches the load at either end, which on a painted or ground surface is the reason to buy it. | ມະຫາຊົນ, ສູນກາງຂອງກາວິທັດ, lifting points, surface finish. |
Specifications of the one way webbing sling
The figures below describe the standard build. Width is not a free choice: it follows from the working load limit and from the safety factor, so the same tonnage appears at three widths. ຄວາມຍາວຂອງວົງ, ເລື່ອນ, colour and print are made to the order.
| ຜະລິດຕະພັນ | One way webbing sling, loop ທີ່ບໍ່ມີທີ່ສິ້ນສຸດ (ວົງ) ແບບຟອມ; also supplied with formed eyes as a disposable webbing sling one eye |
|---|---|
| ແບບຟອມ | ວົງປິດ, ແສ່ວແປ, band joined to itself — no eye, no end, no metal fitting |
| ກໍ່ສ້າງ | Single ply standard; double ply for a higher figure at the same width or a stiffer bearing face |
| ເສັ້ນໄຍ | High tenacity ຜ້າແພ polyester (PES); ໄນລອນ (PA) for shock loads and polypropylene on request |
| Web thickness | 4 ມມມາດຕະຖານ (3–10 mm across the range) |
| ຂີດຈຳກັດການໂຫຼດ | 1 t – 12 t single ply; 2 t – 24 t ສອງ ply |
| ຄວາມກວ້າງຂອງແຖບ | 25 ມມ – 300 ມມ, set by the working load limit and the safety factor |
| ປັດໄຈຄວາມປອດໄພ | 5:1 / 6:1 / 7:1, selected at order |
| ຄວາມຍາວຂອງວົງ | 0.5 m – 100 m in one continuous loop; minimum length rises with width |
| ການຍືດຕົວ | ≤ 7 % ໃນຂອບເຂດຈໍາກັດການໂຫຼດ (polyester) |
| ອຸນຫະພູມເຮັດວຽກ | −40°C ເຖິງ +100 °C ຢ່າງຕໍ່ເນື່ອງ; polyester melts at about 258 °C, so sparks and hot work need a sleeve |
| ສີ | BS EN 1492-1 capacity colour — 1 t violet, 2 t ສີຂຽວ, 3 t ສີເຫຼືອງ, 4 t ສີເທົາ, 5 t ສີແດງ, 6 t ສີນ້ໍາຕານ, 8 t ສີຟ້າ, 10 t ສີສົ້ມ; special colours and printed logos on OEM orders |
| ປ້າຍກຳກັບ | ຂີດຈຳກັດການໂຫຼດ, ຄວາມຍາວຂອງວົງ, ປັດໄຈຄວາມປອດໄພ, ຈໍານວນຊຸດ, customer reference; blue or white label |
| ມາດຕະຖານ | BS EN 1492-1; ASME B30.9 for the 5:1 ສ້າງ; other market standards to order |
| ການຫຸ້ມຫໍ່ | Bundled, cartoned or palletised, labelled per pack and listed on the packing list against the printed reference |
| ລະຫັດ HS | 630790 |
Choosing the size: the figure from the pick, the width from the surface
Two decisions are made separately and in this order. ໄດ້ ຈໍາກັດການໂຫຼດເຮັດວຽກ comes from what one pick has to carry, divided by the mode factor of the hitch — not from the mass of the load as weighed. ໄດ້ ຄວາມກວ້າງ then comes from the surface being wrapped: a coated pipe and a painted machine at the same tonnage do not want the same band.
| Load at one pick | ຂີດຈຳກັດການໂຫຼດ | ກວ້າງ (5:1 / 7:1) | ການນໍາໃຊ້ປົກກະຕິ |
|---|---|---|---|
| ເຖິງ 0.8 t | 1 t | 25 / 30 ມມ | ທໍ່ເຈາະຂະຫນາດນ້ອຍ, single light sections, tooling |
| 0.8 – 1.6 t | 2 t | 50 / 60 ມມ | Pipe to 6″ in single joints, small bundles |
| 1.6 – 2.4 t | 3 t | 75 / 90 ມມ | Pipe to 10″, rebar bundles, ຊອງໄມ້ |
| 2.4 – 3.2 t | 4 t | 100 / 120 ມມ | Coated pipe 12–16″, sheet packs |
| 3.2 – 4.0 t | 5 t | 125 / 150 ມມ | Heavy wall pipe, ເຄື່ອງຈັກ, ຫີນ |
| 4.0 – 4.8 t | 6 t | 150 / 180 ມມ | Pipe bundles, ພາກສ່ວນໂຄງສ້າງ |
| 4.8 – 6.4 t | 8 t | 200 / 240 ມມ | Large bundles, ມ້ວນ, log packs |
| 6.4 – 8.0 t | 10 t | 250 / 300 ມມ | Export pipe bundles, heavy fabricated items |
| 8.0 – 9.6 t | 12 t | 300 / 300 ມມ | Maximum single ply; go to double ply above this |
ຄວາມຍາວ: the two conventions, and why the mistake is expensive here
A loop has no ends to measure between, so the trade quotes the same article two ways. The two figures differ by about a factor of two, and on a one trip band the error surfaces at the far end — in front of a customer, with no second band to swap in.
| You write | It means | When to use it |
|---|---|---|
| Loop circumference 4.0 ມ | One full turn round the load, measured round the closed loop | The band is ordered to wrap a known girth |
| Band length 2.0 ມ, laid flat | The webbing cut length before joining — half the circumference | The band is priced and cut by the metre |
| Girth at the pick 1.6 ມ, two picks | The dimension of the load itself, plus the number of bands | Safest form on a first order: it needs no convention at all |
What the same loop carries in each hitch
The figure on the label describes the vertical arrangement only. All three hitches are rigged without any change to the article, which is why the arrangement has to be stated before the width is fixed.
| ການຈັດ | ປັດໄຈ | ກ 5 t loop gives | ບ່ອນທີ່ມັນຖືກນໍາໃຊ້ |
|---|---|---|---|
| Vertical — loop hangs, load on one side | 1.0 | 5.0 t | Single point pick, hook through the loop |
| Choked — round the load and back through itself | 0.8 | 4.0 t | ທໍ່, ທໍ່, poles, ກອງ, ມັດ |
| ກະຕ່າ, ຂາ 0–45° | 2.0 | 10.0 t | Under a bundle with both legs carrying |
| ກະຕ່າ, ຂາ 45–60° | 1.4 | 7.0 t | Wide bundles, short sling legs |
The choke is the arrangement a loop is bought for, and it is also the one that costs 20 % of the printed figure. ກ 4.5 t pipe bundle choked on a 5 t loop is an overload, not a margin — the answer is the next width up, not a longer band.
Coating and surface compatibility
| ດ້ານ | Risk in the lift | Sling measure |
|---|---|---|
| Hot dip galvanised pipe | Zinc layer rubbed through by sliding hardware; white rust at a scored line | loop ບໍ່ມີທີ່ສິ້ນສຸດ, ບໍ່ມີອຸປະກອນເສີມ, 100 mm band or wider, dry and grit free |
| 3PE / FBE anti-corrosion pipe | Point pressure and edge cuts at the coating; repairs are costly at destination | Wide soft face, padded protector at the contact, choke without a wire rope stinger |
| PVC and PE pipe | Denting and ovality under a narrow band, especially in warm weather | 150–200 mm band, two picks, basket rather than a single choke on long joints |
| Stainless tube | Iron contamination and scratching from contact with steel fittings | Dedicated synthetic sling, ບໍ່ມີການຕິດຕໍ່ໂລຫະ, clean storage before issue |
| Copper tube | Brinelling and burrs from hard contact | Loop only, band width matched to tube diameter |
| Painted or machined assemblies | Print-through and paint damage at the sling contact | Soft loop, edge sleeves, protector where the band crosses an arris |
ເຄື່ອງຫມາຍ, label and what it has to survive
On a single trip article the print is the record, so the marking is a specification line rather than a detail. Four things belong on the label: ຂີດຈໍາກັດການໂຫຼດເຮັດວຽກ, the loop length with its convention, ປັດໄຈຄວາມປອດໄພ, and the reference the despatch actually uses — a batch, ຈໍານວນຊອງ, ຈໍານວນຄໍາສັ່ງຫຼືຈໍານວນສ່ວນຂອງທ່ານເອງ. That reference is what ties the band on a quay to the line on a packing list in an office.
- ຖືກຕ້ອງຫຼັງຈາກການເດີນທາງ, ບໍ່ແມ່ນຫຼັງຈາກການຜະລິດ. Small, low contrast print on a face that enters the choke will not be read at the far end.
- ສີເປັນຊ່ອງທີສອງ. ຫນຶ່ງສີຕໍ່ປະເພດຊອງ, per customer or per tonnage lets a container of identical bands be sorted at a glance.
- Printed to your string. The label can carry your reference in the exact case and format you send, ແລະແຖບສາມາດບັນຈຸພາຍໃນ crate ໄດ້, ມັດເປັນມັດ ຫຼື taped ເປັນມັດ, ຕິດສະຫຼາກຕໍ່ຊຸດ.
The single inspection, and what it looks at
A one trip band is checked once, ຢູ່ໃນບັນຫາ, while a fault can still be replaced from the same consignment. Look at four things, ໃນຄໍາສັ່ງນີ້: the weave where it meets the load (ການຕັດ, ການຂັດ, a glazed or pinched face), the join where the loop closes, the label — an unreadable figure cannot be matched to the pack it was cut for — and what the band has been lying in. ຈີ່, Swarf, ນ້ ຳ ມັນແລະນ້ ຳ ຢືນຢູ່ໃນບ່ອນຕິດຕໍ່, and a clean band is the cheapest protection available.
Do
- State the hitch, the girth and the mass per pick
- Add edge protection at a cut sheet, mesh or arris
- Keep the band dry, clean and off the ground before issue
- Retire the band at the destination, not back to a rack
Do not
- Shorten a sling with a knot or join two by knotting
- Repair webbing by stitching, ການເຊື່ອມໂລຫະຫຼືຄວາມຮ້ອນ
- Drag a loop over a cut edge or across the ground
- Re-issue a band that has done a journey
Protect the band from sharp edges, hot surfaces and welding spatter with a sleeve or a padded protector. ຂ້າງເທິງ 100 °C, or where sparks are present, polyester is the wrong fibre and an sling ຕະຫຼອດທີ່ບໍ່ມີທີ່ສິ້ນສຸດ with a heat resistant cover is the article to discuss.
One way or returnable: the arithmetic
The commercial case is simple and it is arithmetic, not preference. A one way band costs less per unit than a returnable sling and carries no return freight, ບໍ່ມີທະບຽນກວດກາ, no repair and no loss write-off — but it has to be counted correctly, because nothing comes back to cover a shortfall. ນັບຈາກຊຸດ, ບໍ່ແມ່ນມາຈາກໂຕນ: two picks per pack is two bands, a four point lift is four, ninety packs at two picks is 180 ວົງດົນຕີ. Add two to five per cent for the band cut while the pack is made up, so a shortfall becomes a line on the order instead of a delay at the dock.
Where the same slings are used week after week in one yard, a returnable article inspected between lifts is the cheaper order over a year. Where the sling leaves with the load — export packing, one off shipments, work that ends on a customer’s site, or a coated pipe consignment that is re-slung at the far end — the one way loop is the right purchase. Where the whole consignment travels as a netted unit instead of being slung joint by joint, ກ ສຸດທິຍົກສິນຄ້າ is the article to price against it. The form with eyes at both ends, for loads that are hooked rather than wrapped, ຢູ່ໃນ disposable one way sling ໜ້າ; the wider family is on the slings ໃຊ້ດຽວ ແລະ single use lifting slings endless loop ໜ້າ.
What to send with the enquiry
Six lines are enough to quote a made to order band, and they remove every ambiguity that shows up later at the load:
- The load — pipe diameter and wall, bundle mass, or the finished item.
- The pick positions — how many, and how far apart.
- The arrangement — vertical, choked ຫຼືກະຕ່າ, and the angle if basket.
- The girth at each pick, or the loop length with its convention named.
- The safety factor your market works to, and the standard to mark to.
- The reference to print, and the quantity per pack.
Request a quotation for one way webbing slings
ສົ່ງການໂຫຼດ, ເລືອກຕໍາແຫນ່ງ, the girth and the factor. ພວກເຮົາກັບຄືນມາດ້ວຍຄວາມກວ້າງ, the loop length, the finished weight and the marking — on a drawing, before the band is cut.
Send your sling specification · Telephone / WeChat +86 180 6600 2268 · 702461526@qq.com
ສວນອຸດສາຫະ ກຳ Lifute, ເມືອງ Taizhou, ແຂວງຈຽງຊູ, China · HS code 630790
ຄຳຖາມທີ່ມັກຖາມເລື້ອຍໆ
What is a one way webbing sling?
A rated polyester webbing sling supplied for a single journey. ມັນເດີນທາງດ້ວຍການໂຫຼດ, is inspected once at the point of issue and is not recovered or re-issued. The endless form is a closed loop of flat woven polyester with no eye and no metal fitting, which is why it is the form chosen for pipe, tube and bundles.
Is a one way sling weaker than a reusable one?
ບໍ່. ເສັ້ນໄຍ, ທໍ, ຄວາມກວ້າງ, ປັດໄຈຄວາມປອດໄພ, working load limit and marking are specified exactly as for a returnable sling. The word describes the journey, not the grade, so a lower factor or a narrower band is not a saving on a single trip article.
Will a webbing sling scratch galvanised or anti-corrosion pipe?
The band is synthetic fibre and no shackle, hook or thimble touches the load when an endless loop is used, so there is nothing to cut or gouge a zinc, epoxy or polyethylene coating. ຄວາມກວ້າງແມ່ນມາດຕະການປ້ອງກັນ: ແຖບກວ້າງຂຶ້ນ, the lower the pressure at the contact.
How is the length of an endless webbing sling measured?
Two conventions are used and they differ by about a factor of two: the circumference of the closed loop, and the length of the band laid flat before joining. Name the convention with the figure, or give the girth of the pipe or bundle the loop must go round.
Can the same loop be used in a choker hitch?
ແມ່ນແລ້ວ, and a closed loop is the natural form for a choke on pipe, tube and bundles. ຕົວເລກ choked ແມ່ນ 0.8 of the vertical working load limit, ດັ່ງນັ້ນ ກ 5 t loop chokes 4 t. Select the width for the arrangement actually used.
Which safety factor should I order, 5:1, 6:1 ຫຼື 7:1?
7:1 is the usual European figure for flat woven webbing slings to BS EN 1492-1, 5:1 is the customary North American figure under ASME B30.9, ແລະ 6:1 ນັ່ງລະຫວ່າງເຂົາເຈົ້າ. ໂຕນດຽວກັນຢູ່ໃນປັດໃຈທີ່ແຕກຕ່າງກັນແມ່ນບົດຄວາມທີ່ແຕກຕ່າງກັນທີ່ມີຄວາມກວ້າງແຕກຕ່າງກັນ, so the factor belongs on the enquiry.
ແຖບສາມາດພິມດ້ວຍການອ້າງອີງຂອງພວກເຮົາເອງ?
ແມ່ນແລ້ວ. ຂີດຈຳກັດການໂຫຼດ, ຄວາມຍາວຂອງວົງ, ປັດໄຈຄວາມປອດໄພ, batch and your own pack, order or part number can be printed as produced, in the exact string you send, so a band at the far end can be tied back to a line on the packing list.