제품 카테고리

5 Ton Heavy Duty Ratchet Straps

간단한 설명:

리프트 슬링 리깅 회사 생산 5 Ton Heavy Duty Ratchet Straps,10 톤 래칫 스트랩,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

5 ton heavy duty ratchet straps: 50 mm 폴리에스터, 5,000 그리고 휴식, LC 2,500 daN 에서 EN 12195-2. 스테인레스 304/316 and aramid high-temp builds. 공장 직접.

제품 세부정보

리프트 슬링 리깅 회사 생산 5 Ton Heavy Duty Ratchet Straps,10 톤 래칫 스트랩,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

Cargo restraint · EN 12195-2

5 Ton Heavy Duty Ratchet Straps

50 mm 폴리에스테르 웨빙, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

2,500 그리고 매질 용량 5,000 그리고 파단강도 350 그리고 STF의 50 daN hand 3-10m standard length
5 ton heavy duty ratchet straps with hook options: claw hook, 플랫 후크, D ring and S hook

“5 ton heavy duty ratchet straps” is the phrase buyers search for, and the reason this page exists is that the phrase covers two different articles. 에 50 mm polyester assembly the breaking strength is 5,000 그리고 그리고 매질 용량 (LC) ~이다 2,500 그리고. Both numbers are real, both are printed on the same label, and quoting one against the other is how trailers get overloaded. We build the assembly to EN 12195-2, mark it, and state both figures so the comparison you make at quotation stage is between like and like.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 에게 10 m을 표준으로, LC 2,500 그리고, STF 350 그리고 N에서 50 그리고 손의 힘. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.

Part of the 웨빙 슬링 and lashing range. 그만큼 50 mm specification in isolation sits on the 50 mm 5000 kg 래칫 래싱 벨트 페이지.

What “5 Ton” Actually Means on a Ratchet Strap

Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. EN 아래 12195-2 매는 끈의 웨빙은 매는 용량의 최소 두 배에 도달해야 합니다., which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.

테이블 1 — The three numbers on a 5 ton heavy duty ratchet strap
수치 Value on the 50 mm assembly 설명하는 내용 How it gets misread
최소 파괴 강도 5,000 그리고 (5,000 kg) 당김 테스트에서 어셈블리가 실패하는 하중 Read as the working figure — the mistake that overloads a trailer
래싱 용량 (LC) 2,500 그리고 (2.5 티) 어셈블리가 유지하도록 평가된 구속, printed on the label 리프팅 슬링의 WLL과 비교, which is a different duty altogether
표준 인장력 (STF) 350 그리고 N에서 50 그리고 손의 힘 The tension one person reaches with the ratchet handle LC와 혼동됨, 그래서 운영자는 유용한 지점을 계속해서 지나갑니다.
Ask for both numbers. Two suppliers quoting “5 tonne” can be quoting the breaking strength and the working figure — a factor of two apart — and a North American catalogue printing the same article as “10,000 lb” is quoting breaking strength in pounds. 같은 벨트, different unit, same trap.

왜 50 mm Build Is the Heavy-Duty Default

Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. 그만큼 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.

테이블 2 — Width ladder: where 50 mm sits
웹 폭 Typical LC 파괴 강도 무엇을 위해 구입하는가
25 mm (1 ~에) 400–500 daN 800–1,000 daN Tool boxes, light restraint, tight anchor eyes
35 mm (1-3/8 ~에) 750 그리고 1,500 그리고 Van and trailer decks, general cargo
38 mm (1-1/2 ~에) 1,000–1,500 daN 2,000–3,000 daN 강판, 파이프 묶음, plant
50 mm (2 ~에) 2,500 그리고 5,000 그리고 Heavy cargo restraint, 코일, 기계, 컨테이너
75-100mm 5,000 daN and up 10,000 daN and up Abnormal loads, where the bed allows the width

The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.

Standard Specification of the 5 Ton Assembly

테이블 3 — 50 mm 5 ton heavy duty ratchet strap: 기술적인 매개변수
목 사양
가죽 끈 100% 고강도 폴리에스테르, 능직, UV 안정화, 50 mm ± 2%
밴드 두께 / 대량의 1.8 mm 공칭 / 88 g per metre
래싱 용량 (LC) 2,500 그리고 어셈블리 당
최소 파괴 강도 5,000 그리고 (2:1 against LC)
표준 인장력 (STF) 350 그리고 N에서 50 그리고 손의 힘
텐셔너 Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle
LC에서의 신장 7% 이하
서비스 온도 −40°C ~ +100 ℃ (폴리에스테르 웨빙)
표준 길이 3-10m; 1–30 m to order
마킹 짠 라벨: LC, STF, 길이, 배치 번호, 표준 참조
기준 Designed, tested and marked to EN 12195-2
HS코드 630790

The End Fitting Decides Whether the Strap Fits the Job

The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.

테이블 4 — End fittings for 5 ton heavy duty ratchet straps
입어 보기 Anchors to Notes before ordering
Chassis rave hook Flatbed side rail, chassis lip Check rail thickness and that the hook throat clears it
Claw hook Anchor rings, D rings, recessed eyes Opening must clear the ring; load on the crown only
D ring / 델타 링 Welded or bolted anchor points Ring bore at least as wide as the webbing
Flat snap hook E-트랙, slotted rail, 구멍 Confirm slot width; snap gate must close fully
S hook 파이프, 울타리, frame members Both ends must seat without point loading on a weld
Sewn loop / looped ends Around the load or through a bore Nothing metal at the load; ideal for finished surfaces
끝없는, 피팅 없음 Girth only — hulls, 코일, 번들 See the endless loop build below
5 ton heavy duty ratchet straps with hook options: claw hook, 플랫 후크, D ring and S hook
하나 50 mm 밴드, eight ways to terminate it — the hook option decides which anchor the strap can reach.

그만큼 5 Ton Strap in Two Special Builds

Polyester covers most freight, and it fails predictably when it is out of its depth: 주위가 부드러워진다 150 °C and melts at about 255 ℃, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.

Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces

The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 또는 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 그리고 N에서 25 mm 에 2,500 그리고 N에서 50 mm, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.

The grade decision is about chloride, 로드되지 않음. 304 (1.4301) handles rain, 민물, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 그것이 더 강하다는 믿음으로 잘못된 재산에 대한 비용을 지불하는 것입니다.. 애플리케이션이 안전과 관련된 경우, 송장 설명이 아닌 공장 인증서의 등급을 확인하세요..

Two shop-floor notes worth passing on. 스테인레스 스레드 담즙, so a dry 316 너트는 a에 세게 달려 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. 스테인리스는 소금물에 있는 알루미늄에 볼트로 고정되어 갈바닉 쌍을 형성합니다., so where the strap anchors to an alloy frame, 접촉을 격리하다.

Full range and grade comparison: 끝없는 스테인레스 스틸 래칫 스트랩.

아라미드 (케블라) ratchet straps — for heat, sparks and cut edges

Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 ℃. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.

The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.

Two honest limits. Aramid is flame retardant, not fireproof: molten steel, ladles and hot slag still need a heat shield or a stand-off. And low elongation is exactly wrong for snatch and shock loads — for those, the polyester band or a dedicated recovery strap is the right article.

Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.

How Many Straps Does the Load Actually Need?

Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.

테이블 5 — Worked example: 50 mm straps at 2,500 daN LC
Straps used Angle to the deck Restraint per strap Total restraint
2 45° 대략. 1,750 그리고 대략. 3,500 그리고
4 30° 대략. 1,250 그리고 대략. 5,000 그리고
4 45° 대략. 1,750 그리고 대략. 7,000 그리고
4 60° 대략. 2,165 그리고 대략. 8,660 그리고
6 45° 대략. 1,750 그리고 대략. 10,500 그리고

The arithmetic is an illustration, not a lashing plan: 안에 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.

어디에 5 Ton Ratchet Strap Earns Its Keep

  • 평판, container and plant trailer restraint — the volume application for the 50 mm build.
  • 강철 코일, 투수판, billet and pipe bundles, with edge protection at the contact points.
  • 기계, moulds and skid-mounted plant, 어디서 25 mm strap has neither the width nor the tension.
  • 목재 팩, 상자와 스틸리지, including the endless form that simply closes round the pack.
  • Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
  • 선박, marina and wash-down duty in 304 또는 316 where plated hardware would be a maintenance item.
  • Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.
5 ton heavy duty ratchet straps securing a timber crate on a flatbed truck
50 mm straps over a timber crate on a flatbed — two legs at roughly 45°, hooks seated on the crown of the rail.

색상, Printing and Private Label

Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, 주황색, 노란색, 검은색, 빨간색, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, 길이, standard and traceability code. Cartons of 10 에게 20 조각들, palletised for export, with neutral or own-brand packaging as required.

테스트, Traceability and the Paperwork Buyers Ask For

Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. 테스트 보고서, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.

One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.

자주 묻는 질문

는 5 ton ratchet strap rated to lift 5 톤?

아니요, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.

Why does the same strap get called 5 톤과 2.5 톤?

Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.

50 mm 또는 38 mm for a flatbed?

50 mm, unless the anchor points are small. 그만큼 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; 그만큼 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.

Do I need 304 또는 316 스테인레스?

316 where chloride is present — sea air, 소금 스프레이, 제빙소금, boatyards, 식용 식물. 304 is enough for rain, 민물, condensation and indoor wash-down. The difference is corrosion resistance, 힘이 아니라.

At what temperature does polyester fail, and what does aramid do instead?

Polyester softens around 150 °C and melts at about 255 ℃, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 ℃, and chars at about 427 녹는 대신 °C. 위에 400 ℃, or against molten metal, both need a heat shield.

Can the strap be supplied with a printed brand and a custom length?

예. 폭, 길이 30 중, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.

견적 요청

Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, 환경 (salt, 열, 세척), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.

리프트 슬링 장비 회사

리푸테 산업단지, 타이저우시, 장쑤성, 중국

전화: +86 523 8693 5818 · 왓츠앱: +86 180 6600 2268

이메일: 702461526@qq.com · HS code 630790

Send your lifting details for a quotation →

관련 제품

리프트 슬링 장비 회사 · Lifute Industrial Park, 타이저우시, 장쑤성, 중국 · HS 코드 630790
전화 +86 523 8693 5818 · 왓츠앱 +86 180 6600 2268 · lift98@jslift.com · xulft.com

 

메시지를 남겨주세요

맨 위로 스크롤