Lift sling rigging company produce Double Ply Endless Lifting Sling,3 Ply Endless Nylon Flat Sling,2 Ply Polyester Endless Lifting Sling,Double Ply Endless Nylon Lifting Sling,2-Ply Endless Type Web Sling,2 ply Endless Polyester sling,2-Ply Endless Type Web Sling,2-Ply Endless Lifting Web Sling,2 Ply Endless Polyester Web Sling,3-Ply Endless Polyester Lifting Sling,Three Ply Endless Nylon Sling,,4 Ply Endless sling,4 Ply Endless Polyester Lifting Sling,4 ply Endless Nylon Lifting Sling,Double Ply Endless Webbing Sling,Three Ply Endless Webbing Sling,Four Ply Endless Webbing Sling.
Endless lifting sling · duplex and multi-ply · 2, 3 그리고 4 층
Double Ply Endless Lifting Sling
Two layers in the one band: more capacity at the same width, a thicker and more forgiving bearing face, and abrasion reserve behind the first layer. 1 ~에 30 ~에 7:1 둘 하나 1492-1, with 3-ply and 4-ply built to order.

둘, three and four ply: what the number changes
Ply is the number of layers woven into the one band the loop is made from — not two slings, and not two bands side by side. Each layer added does three things at once, and the third is the one buyers ask about least and notice most:
- It thickens the section. The band becomes a deeper, stiffer beam in cross-section, which is why it lies down on the load instead of draping over it.
- It adds capacity at the same width. That is the whole reason duplex exists above the single-ply ladder — the published range runs to 30 티, 이상 10 t the ladder itself specifies duplex.
- It adds cushioning. The extra layers sit between the load and the load-bearing core of the band: contact pressure spreads over a thicker, more compliant stack, and an edge has more material to work through before it reaches anything structural. That is why 3-ply and 4-ply are asked for on precast, machined and coated surfaces rather than on plain steel.

The four builds, 나란히
The comparison below is qualitative on purpose: this site publishes capacities and widths for the single-ply and duplex ladders, and builds 3-ply and 4-ply to order. 두께, weight and working load limit for those two are therefore confirmed against the order, not taken from a table on a web page.
| 싱글 플라이 | 더블 플라이 (듀플렉스) | 3-주름 | 4-주름 | |
|---|---|---|---|---|
| Layers in the band | 하나 | 둘 | 삼 | 4개 |
| 부분 | Thinnest in the range | Roughly twice the single-ply section | Thicker again | Thickest build we make |
| Capacity at the same width | Published ladder | Higher — the reason duplex exists above the single-ply range | Built to order | Built to order |
| Cushioning on the load | 기준선 | Noticeably more compliant stack | More again | The most forgiving face |
| 손질 | Folds small, tight radius | 더 단단함, sits flat on the hook and the load | Stiffer again | Least supple; carried and stored flat |
| Where it is asked for | General yard work, tight gaps, 작은 직경 | High capacity in a narrow width, rough edges, heavy abrasion | 프리캐스트, machined and coated surfaces | Heaviest duty, maximum cushioning |
| Published data | Ladder on the single ply page | Ladder and ply column on this page | Confirmed on the acknowledgement | Confirmed on the acknowledgement |
용량: where the ply column turns over
Working load limits are straight lift at 7:1 둘 하나 1492-1, with the ply column exactly as this site publishes it. Read it as an instruction, not a menu: ~에서 2 t upward either build will do, 이상 10 t the ladder itself says duplex.
| WLL, 스트레이트 리프트 | 색상 | 기준폭 | 주름 | 길이 범위 | 질식하다 (× 0.8) |
|---|---|---|---|---|---|
| 1 티 | 제비꽃 | 주문시 확인 | 하나의 | 0.5 – 100 중 | 0.8 티 |
| 2 티 | 녹색 | 50 mm | 하나의 / 듀플렉스 | 1 – 100 중 | 1.6 티 |
| 3 티 | 노란색 | 75 mm | 하나의 / 듀플렉스 | 1 – 100 중 | 2.4 티 |
| 4 티 | 회색 | 100 mm | 하나의 / 듀플렉스 | 1.5 – 100 중 | 3.2 티 |
| 5 티 | 빨간색 | 125 mm | 하나의 / 듀플렉스 | 1.5 – 100 중 | 4.0 티 |
| 6 티 | 갈색 | 150 mm | 하나의 / 듀플렉스 | 1.5 – 100 중 | 4.8 티 |
| 8 티 | 파란색 | 200 mm | 하나의 / 듀플렉스 | 2 – 100 중 | 6.4 티 |
| 10 티 | 주황색 | 250 mm | 하나의 / 듀플렉스 | 2 – 100 중 | 8.0 티 |
| 위에 10 티 | 색상 코드 없음 | 주문시 확인 | 듀플렉스 | 주문하려면 | 라벨이 지배한다 |
The range as a whole runs 1 ~에 30 티, 25 mm 에 300 mm 이상, finished loops 0.5 m ~ 100 중, ~에 7:1 standard with 5:1, 6:1 그리고 8:1 주문하다. Final width, 플라이 및 마감 중량은 주문 확인서에서 확인됩니다..

Where the second layer earns its keep
Duplex and the heavier plies are bought for four situations, and in each one a wider single band is either impossible or second best:
- The capacity does not fit the width. A narrow load or a small hook caps the band width; the ply is what is left to raise the figure.
- The edge is rough rather than sharp. Not a burr that will cut — the kind of edge that abrades. A doubled band has a second layer behind the first, so wear has further to go before the load path is compromised.
- The surface must not be bruised. 코팅, 그린, machined or precast faces are where the extra thickness reads as extra cushioning: a thicker, more compliant stack over the same footprint.
- The band must sit flat. A duplex band is stiffer and lies down across a plate or a machined face instead of curling up at the edges, which keeps the contact full width.
Three and four ply, honestly
The 3-ply and 4-ply endless slings in this range are the same construction taken further: a third and a fourth layer in the band, a thicker section again, more capacity at a given width and a more forgiving face. They are built to order. We do not publish a web table for them because the figure depends on the weave, the fibre and the finished width, and a number on a page that has not been proof tested is worse than no number at all.
What we will do is quote them properly: tell us the load, 장애, the width you can live with and the surface you are protecting, and the ply, 두께, weight and working load limit come back on the acknowledgement with the test certificate behind them.

하나의 관절, and it is thicker here
끝없는 슬링은 끝없이 사용됩니다, 매끄럽지 않은. 밴드는 그 자체로 겹쳐져 있으며 촘촘하고 평행한 스티치 라인으로 마감되어 있습니다., and that lap is the only made connection in the load path. On a multi-ply build the lap is thicker and the stitching passes through more layers, so inspect both faces: 부러지거나 당겨진 바늘, a lap starting to open, and abrasion where the lap crosses an edge.
Past the joint the loop is one continuous band, and on a duplex or 3-ply sling there is no sleeve hiding the core — every part of what is carrying the load is visible on the face. That is the practical difference from a round sling, where only the sleeve can be inspected.
Three hitches, same loop
The label figure is the straight-lift rating and every other arrangement is derived from it. Size to the hitch the crew will rig.
| 걸다 | 모드 인자 | 현장에서의 의미 |
|---|---|---|
| 수직의 | × 1.0 | 라벨 수치가 직접 적용됩니다. |
| 질식하다 | × 0.8 | 에이 4 초크에로드하지 마십시오 5 t sling — the wrap grips as the load comes on |
| 바구니, 수직에 가까운 다리 | × 2.0 | Both sides of the loop carry the load and the bearing face is doubled |
| 바구니, 7°–45° | × 1.4 | As the legs open the rating falls; plan the angle, 무게 뿐만 아니라 |
| 바구니, 45°–60° | × 1.0 | At wide angles the basket advantage is gone |
길이: circumference or effective working length
닫힌 루프에는 측정할 끝이 없습니다., so the trade quotes the same sling two ways and they differ by about a factor of two. Circumference is the perimeter of the loop; effective working length is the usable height you get, roughly half the circumference because the loop is doubled when it hangs.
| 다음과 같이 인용됨 | 측정 대상 | 같은 슬링은 |
|---|---|---|
| 둘레 | The perimeter of the loop — total band in the article | 2 중 |
| 효과적인 작업 길이 | 사용 가능한 높이; the loop doubles when it hangs | 1 중 |

섬유, colour and marking
The standard build is high-tenacity polyester (PES): no more than 3% elongation at the working load limit and 10% 파단 하중에서, so the hook height stays predictable, 작동 범위는 −40 °C ~ +100 ℃. Nylon takes the shock and abrasion duties, polypropylene the wet and the cheap, and UHMWPE and aramid the strength-to-weight and heat cases.
Colour follows EN 1492-1 and marks the capacity band, never the ply — violet 1 티, 녹색 2 티, 노란색 3 티, 회색 4 티, 빨간색 5 티, 갈색 6 티, 파란색 8 티, 주황색 10 t — with one black transverse stripe per tonne as an optical second check. 위에 10 t there is no colour code and the sewn label is the only rating: 작업 부하 제한, 재료, 기준, 길이 및 추적성 코드.

Testing and paperwork
Every sling is proof tested on our own 1000 t machine before it leaves Taizhou, and the facilities hold CNAS, CE 및 DNV 인증, producing to EN 1492-1, ISO 4878 그리고 JB/T 8521. Each order ships with a test certificate, the blue working load limit label and a packing list; HS코드 630790. 자체 브랜드 라벨, special weave colours and customer packing are available on OEM orders.

자주 묻는 질문
What is the difference between double ply and duplex?
Nothing — they are the same build: two layers of webbing woven into the one band the loop is made from. This site uses duplex in its specification table and double ply in the product name, and both mean two layers.
Does double ply mean double the capacity?
Not literally. Two layers add substantial capacity at the same width, but the figure is set by the finished band and confirmed by proof test — it is not a doubling of the single-ply number. On the published ladder the practical reading is that duplex is what carries the range above 10 티, and what goes on a narrow band where a wide one will not fit.
Why do 3-ply and 4-ply have no table on this page?
Because the figure depends on the weave, the fibre and the finished width, and we would rather quote a combination that has been proof tested than publish a number that has not. 짐을 보내세요, the hitch and the width, and the ply, 두께, weight and working load limit come back on the acknowledgement with the certificate.
Is more ply really more cushioning?
예, in the sense that matters on site: more layers mean a thicker, more compliant stack between the load and the load-bearing core of the band, so contact pressure spreads and an edge has more material to work through. That is why 3-ply and 4-ply are specified on precast, machined and coated surfaces rather than on plain structural steel.
Can a double ply sling be choked?
예 — 수직, choked and basket all come from the same loop. A stiffer band chokes less tightly than a supple one, so check that the wrap actually beds onto the load; the choked factor of 0.8 applies as it does to any sling.
Will it mark aluminium or painted steel?
밴드는 합성 섬유이며 피팅이 하중에 닿지 않습니다., 체인이나 와이어 로프처럼 긁히거나 버가 생기지 않습니다.. Width and ply are the two protection measures: a wider, thicker band spreads the same load over a larger, softer footprint.
견적요청
짐을 보내세요, the hitch and the width you can live with
The load — what it is, its girth at the pick positions, and its surface;
The hitch — vertical, 질식하거나 바구니, and the leg angle if it is a basket;
The width limit — the narrowest band the hook and the load will accept;
The ply you are considering — duplex, 3-겹 또는 4겹, and why;
The length — by circumference or effective working length;
표준, destination market and marking, including own-brand labels.
다음엔 어디로 갈까
- The endless lifting sling range — every closed form, compared by load;
- Single ply endless lifting sling 그리고 단일 플라이 끝없는 플랫 슬링 for the lighter build and its full size tables;
- Polyester endless flat strap sling for the fibre and specification detail;
- Heavy duty endless loop strap slings 그리고 플랫 리프팅 슬링 for the widest, heaviest end of the range;
- 강관 리프팅 스트랩 for pipe duty and 끝없는 둥근 슬링 for the sleeved alternative;
- 웨빙 슬링 in all builds, 그리고 contact.