• 집 /
  • 제품 /
  • 헤비 듀티 20 Ton Polyester Cargo Lifting Net

제품 카테고리

헤비 듀티 20 Ton Polyester Cargo Lifting Net

간단한 설명:

Lift sling rigging company produce Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

20 t polyester cargo lifting net: 7:1 안전계수, 100 mm duplex bands, four or eight points, cut to the load footprint and proof tested per net.

제품 세부정보

Lift sling rigging company produce Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

Cargo lifting net · polyester · 20 티 클래스

헤비 듀티 20 Ton Polyester Cargo Lifting Net

에이 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

20 티 작업 부하 제한 140 티 minimum breaking load 100 mm duplex band 8 리프팅 포인트
Heavy duty polyester flat webbing cargo lifting net laid out, wide bands in a square mesh

A heavy duty 20 ton polyester cargo lifting net is a flat lattice of wide high-tenacity polyester bands, stitched into a square mesh with a doubled border and four or eight reinforced lifting points. The load sits inside the mesh and is carried across the full width of every band beneath it, so the pressure on the cargo is spread over a face rather than concentrated on four sling legs.

We build these nets to order in Taizhou: band width and layer, 망사, 순 크기, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.

The number behind “20 ton”. The working load limit is 20 t and the safety factor is 7:1, so the net’s minimum breaking load is 140 티. That figure is what the test bed proves; 그만큼 20 t is what you are allowed to lift, in the arrangement the net was rated in.

Why polyester at this rating

~에 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.

테이블 1 — Polyester against nylon for a 20 t net
폴리에스테르 (애완 동물) 나일론 (아빠)
Stretch under a steady load Low — the net stays square and the load stays level Markedly higher; the net settles and the load can tilt
충격 흡수 보통의 Best in the family; 18–22 % 휴식시 신장
수분 흡수 매우 낮음, dries quickly 에 대한 4 %, with some strength loss when saturated
Repetitive crane cycles The usual choice Better where pickups are rough
작동 온도 −40°C ~ +100 ℃ Lower at the top end
Best fit for a 20 로드하지 마세요 가방에 담아, 팔레트화, bundled or stacked cargo lifted on a cycle Irregular or shocky loads that must settle into the mesh
Nylon rope cargo net for comparison with a flat webbing net
The rope alternative: better on irregular loads, but it stretches far more than a polyester band net under a steady 20 티.

What changes when the rating goes to 20 티

Capacity is not a property of the net’s size. It comes from four things moving together: 밴드, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.

테이블 2 — Build steps from a light net to a 20 t net
Load band Band and build 망사 리프팅 포인트 What else changes
2 – 5 티 50 mm single layer 100 mm 4 corners Standard warehouse net
5 – 10 티 50 – 75 mm, duplex on the load run 100 mm 4 corners, 8 요청 시 Heavier border, reinforced loops
10 – 20 티 75 – 100 mm 듀플렉스 100 – 150 mm 8 전철기 Master ring or spreader beam; net built to drawing
20 – 30 티 100 mm 듀플렉스, band count from the load face 150 mm 8 전철기 Spreader beam in the assembly; proof test per net
위에 30 티 100 mm multi-layer or wider pitch 150 – 200 mm 8 points or more Engineered and tested to the lift, not to a catalogue

Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.

두 가지 결과가 따른다. 첫 번째, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 t에 10 t ring is a 10 t 조립. 두번째, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Corner detail of a heavy duty webbing cargo net, folded double-stitched border and reinforced loop
코너 디테일: the doubled border is spliced into the loop, which is where the whole 20 t passes through — and where a net is inspected first.

Sizing the net to a 20 로드하지 마세요

A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.

  • Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. 에이 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
  • 가방 형태: the flat width has to wrap up the sides and close over the top, 그래서 평평한 너비 = 발자국 + 2 × bag depth. 에이 1.2 m footprint in a 0.6 m deep bag needs about 2.4 m 건너편.
  • Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.
Flat polyester cargo lifting net spread on the floor with four corner lifting loops
Flat form: the net overhangs the load footprint and the four corners gather on the hook, so the cargo sits inside the lattice rather than on top of it.

망사: sized from the cargo, 톤수가 아니라

Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.

테이블 3 — Mesh against the smallest piece in the load
최소 화물 치수 Typical cargo at 20 티 지정할 메쉬
아래에 75 mm 작은 주물, 대량의 구성 요소, drummed goods 100 mm 다이아몬드, 또는 닫힌 가방 그물
75 – 150 mm 벽돌, 가방에 담긴 물건, 쪼개진 돌 100 – 150 mm
150 – 250 mm Sawn packs, bundled tube, 판지, 권투 시합 150 – 200 mm
위에 250 mm 블록, 큰 돌, 철거 잔해 200 – 300 mm

사양

테이블 4 — Heavy duty 20 ton polyester cargo lifting net
매개변수 사양
유형 개방형 플랫 웨빙 격자, 4개 또는 8개의 리프팅 포인트
밴드 소재 100 % 고강도 폴리에스테르 (애완 동물); nylon or UHMWPE on request
대역폭 75 – 100 mm for this class
Band build 듀플렉스 (이중층) on the load-bearing run, single layer elsewhere
메쉬 오프닝 100 – 150 mm; square standard, diamond on request
순 크기 일반적으로 4.0 × 4.0 m ~ 6.0 × 6.0 중, or to the load footprint
작업 부하 제한 20,000 kg in the rated arrangement
안전계수 7:1 - 최소 파단 하중 140,000 kg
테두리와 모서리 Doubled border, 모서리에 연결; reinforced loops, four or eight
피팅 마스터링 또는 그레이드 80 족쇄; spreader beam for eight-point lifts
치료 UV 안정화, 노화 방지, abrasion-resistant finish
작동 온도 −40°C ~ +100 ℃
마킹 WLL, 준비, net size and identification on a sewn label; band printing on request
선적 서류 비치 용량 라벨, 재료 시험 보고서, CE마킹; 우리가 직접 테스트한 1000 t bed
HS코드 630790
Polyester webbing cargo net with the border and lifting loops visible across its width
Border and loops: the perimeter takes the load from corner to corner, so no single stitch line carries the lift.

Eight points, 4개는 아니고, once the load is long

Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.

  • Four points suit square, compact loads where the net is only holding the cargo together;
  • Eight points suit long or wide loads, and any lift where the net must stay flat under load;
  • The spreader or master link, the slings above it and the hook must each be rated at least 20 티;
  • Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.

The leg sees more than the share: ~에 45 deg from the vertical, 에이 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.

검사 및 퇴직

테이블 5 — What ends a net’s service life
확인하다 다음과 같은 경우 폐기하거나 수리하십시오.
Corner loops and their stitching A loop is deformed, the stitching is broken, or the band is cut at the throat
국경 테두리가 잘려있어요, flattened, or has pulled out of a corner
Load-bearing bands Any band is cut, 깊게 마모됨, heat glazed or chemically stained
Mesh geometry The lattice is distorted from an overload — the net no longer sits square
바느질 Stitch lines are broken or pulled at a crossover
Label and printing The WLL or the arrangement is illegible — an unlabelled net cannot be rated

Inspect before each lift and have the net examined by a competent person at the interval your site sets. 깨끗하고 건조하게 보관하세요, 땅에서 떨어져 있고 직사광선을 피하는 곳; never knot, weld or heat-repair a webbing net.

Steel coils loaded inside a webbing cargo net on a factory floor
Coils inside the mesh: at this rating the net is as much a handling tool as a container, and the crane never touches the cargo.

구축 방법, and how the rating is proven

  • Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
  • Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
  • Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
  • Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.

웨빙을 엮고 와이어로프 페럴을 프레스하는 작업도 동일합니다., which is why a net, 에이 웨빙 슬링 그리고 와이어 로프 슬링 on the same lift can be matched in rating rather than bought from three suppliers.

어디서 20 t net does the work

테이블 6 — Sectors that buy this class
부문 네트가 들어올리는 것 평소 빌드
철강 및 제조 번들, 섹션, 정지 부하 플랫 넷, 100 mm 듀플렉스, eight points
Stone and quarry 블록, 쪼개진 돌, 석탄 가방 형태, 150 mm 메쉬, 코너 패치
항구 및 터미널 Bagged and unitised cargo, quay work Flat net on a spreader, 인쇄된 WLL
재목 Sawn packs, 극, sleepers Flat or bag, 150 – 200 mm 메쉬
스크랩 및 재활용 혼합 및 연마 스크랩 대형 메쉬, wear bands at the corners
프리캐스트 콘크리트 Units, 반지, 패널 Flat net with edge sleeves, eight points

자주 묻는 질문

는 20 t rating for the net or for the whole assembly?

The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, 족쇄, spreader and slings above must be rated at least 20 t as well.

Why is the safety factor 7:1 그리고는 아니다 5:1?

7:1 is the factor we build to for this class, which gives a 140 t a에 대한 최소 파단 하중 20 t 등급. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.

Polyester or nylon for a 20 리프트?

Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.

How big a net do I need for a 2 × 2 m load?

At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.

Can it be lifted by a single hook?

Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.

Can you print our brand and the WLL on the net?

Yes — WLL, 준비, 순 크기, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.

견적요청

Send the load and how it is presented

The cargo — what it is, 어떻게 포장되어 있는지, and the weight as presented for the lift;

The footprint — length × width, plus height if a bag form is needed;

The lift — four or eight points, 후크 높이, and whether a spreader beam is available;

The duty — how many lifts a week, indoors or on a quay, and the temperature range;

The paperwork — CE marking, test report and own-brand printing if you need them.

Send the load and the footprint for a quotation →

다음엔 어디로 갈까

리프트 슬링 장비 회사 · Lifute Industrial Park, 타이저우시, 장쑤성, 중국 · HS 코드 630790
전화 +86 523 8693 5818 · 왓츠앱 +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

메시지를 남겨주세요

맨 위로 스크롤