Lift sling rigging company produce Aramid Anti-Drone Nets,knotted Aramid Anti-Drone Net,high strength Anti-Drone Net,Aramid Anti-Drone Net for Restricted Area Protection,Para Aramid Safety Net,Heavy Duty Aramid Fabric Netting for Anti-Drone Defense/Perimeter Protection/Security Facilities.
ಎ aramid anti-drone net is a knotted rope panel hung across the line a small unmanned aircraft would fly through. We supply it as a complete assembly rather than a loose piece of netting: knotted aramid panel, spliced border, corner eyes, tensioners and anchors, quoted per opening so that the panel, the border and the fixings carry the same load.
Two rope sizes cover almost every installation. ಎ 6 mm braided aramid rope breaks at 2.6 ಟಿ and is the panel for perimeter work, prisons, schools and anywhere the aperture has to be fine without the panel becoming heavy. ಎ 10 mm braided aramid rope breaks at 7 ಟಿ and is the panel for real kinetic impact — refineries, substations, ಬಂದರುಗಳು, airfields. Both are knotted, both are spliced into the border, and both are supplied with the fittings that take the load out of the mesh and into the structure.
At a glance
- 6 mm braided aramid rope — breaking force 2.6 ಟಿ
- 10 mm braided aramid rope — breaking force 7 ಟಿ (70.67 kN measured on a 10 mm sample)
- Knotted mesh 40–120 mm, ಗೆ ಫಲಕಗಳು 10 × 20 ಮೀ
- Supplied with border, corner eyes, tensioners and anchors
- No power, no radar, no operator — passive interception
- Does not melt: carbonises from about 400 °C ಮತ್ತು ಅದರ ಆಕಾರವನ್ನು ಹೊಂದಿದೆ
On this page
What the assembly is made of
Four elements decide whether the barrier works, and only one of them is the rope.
- The panel. A 12-strand braided aramid rope, double-knotted into square or diamond mesh. The knot gathers four rope ends, so the load entering from one direction leaves through the other three instead of passing through a clamp.
- The border. The same braid or one size up, double-laid and spliced — never knotted — around the perimeter. The border collects everything the mesh gathers and hands it to the corner eyes.
- The corner eyes and fixing points. Spliced eyes with stainless thimbles at the corners, eyelets or D-rings along the edge at your anchor spacing.
- The anchors. Posts, wall plates or stand-off brackets. A panel that is strong enough and tied to a post that is not will fail at the post.
The construction detail behind the knot, the braid and the fire behaviour is set out on the high strength anti-drone rope net ಪುಟ; this page carries the specification and the fittings you need to place an order.
ತಾಂತ್ರಿಕ ನಿಯತಾಂಕಗಳು
The figures below are the manufacturing range. The batch certificate supplied with the panel governs, and the installed barrier is only as strong as its border and anchors.
| ಐಟಂ | Aramid anti-drone net — standard build |
|---|---|
| ಫೈಬರ್ | ಪ್ಯಾರಾ-ಅರಾಮಿಡ್ (Kevlar-type), ಯುವಿ-ಸ್ಥಿರಗೊಳಿಸಲಾಗಿದೆ; polyester available for light duty |
| ಹಗ್ಗ ನಿರ್ಮಾಣ | 12-ಸ್ಟ್ರಾಂಡ್ ಬ್ರೇಡ್, coreless; 8-strand on 6 mm and below |
| ಹಗ್ಗದ ವ್ಯಾಸ | 6 ಮಿಮೀ ಮತ್ತು 10 ಮಿಮೀ ಪ್ರಮಾಣಿತ; 4 / 8 / 12 ಆರ್ಡರ್ ಮಾಡಲು ಮಿಮೀ |
| Breaking force — 6 ಮಿಮೀ | 2.6 ಟಿ (≈25.5 kN) |
| Breaking force — 10 ಮಿಮೀ | 7 ಟಿ (≈68.6 kN; 70.67 kN measured on sample Dia10mm, 23 June 2026) |
| ಉದ್ದನೆ | ≈3.5 % ವಿರಾಮದಲ್ಲಿ; ಅಡಿಯಲ್ಲಿ 1.5 % ಕೆಲಸದ ಹೊರೆಯಲ್ಲಿ |
| ಜಾಲರಿ | 40 / 50 / 60 / 80 / 100 / 120 ಮಿಮೀ, ಚದರ ಅಥವಾ ವಜ್ರ |
| ನಿರ್ಮಾಣ | ಗಂಟು ಹಾಕಿದ, double knot hand-set and locked |
| ಪ್ಯಾನಲ್ ಗಾತ್ರ | 5 × 10 ಮೀ, 10 × 10 ಮೀ, 10 × 20 m as single panels; larger openings as joined panels |
| ತೂಕ | ≈1.6 kg/m² at 10 ಮಿಮೀ / 100 ಮಿಮೀ ಜಾಲರಿ; ≈0.6 kg/m² at 6 ಮಿಮೀ / 100 ಮಿಮೀ |
| Thermal | No melting point in service; continuous to ≈200 °C; carbonises from ≈400 °C |
| ಬಣ್ಣ | ನೈಸರ್ಗಿಕ ಅರಾಮಿಡ್ ಚಿನ್ನ, ಕಪ್ಪು, ಅಥವಾ ಆರ್ಡರ್ ಮಾಡಲು |
| ಲೇಪನ | ಲೇಪಿತ, ಅಥವಾ ಪಿಯು / neoprene dipped for UV and abrasion on permanent outdoor panels |
| ಗುರುತು ಹಾಕುವುದು | ಪ್ಯಾನಲ್ ಗಾತ್ರದೊಂದಿಗೆ ಟ್ಯಾಗ್ ಮಾಡಿ, ಹಗ್ಗದ ವ್ಯಾಸ, ಜಾಲರಿ, ಫೈಬರ್ ಮತ್ತು ಬ್ಯಾಚ್ ಸಂಖ್ಯೆ |
| ಕರ್ತವ್ಯ | Physical interception — never fall arrest, never lifting |
ಟೇಬಲ್ 1 — Aramid anti-drone net, standard build.
ಗಡಿ, fittings and anchor schedule
Buyers rarely fail on the panel and often fail on what it is tied to. The schedule below is what we supply with a standard opening; every line is confirmed on the approval drawing before the panel is woven.
| ಐಟಂ | ನಿರ್ದಿಷ್ಟತೆ | ವಸ್ತು / ಮುಗಿಸಿ | ಟಿಪ್ಪಣಿಗಳು |
|---|---|---|---|
| ಗಡಿ ಹಗ್ಗ | 10 mm 12-strand aramid, ಎರಡು-ಹಾಕಿದ, spliced | ಅರಾಮಿಡ್, optional PU dip | Never knotted — a knot in the border puts the panel through a single joint at its most loaded point |
| Corner eye | 80 × 160 mm spliced eye, stainless thimble | AISI 316 thimble | One per corner as standard; extra eyes on long spans |
| Edge eyelets | Ø 12 ಮಿಮೀ, ನಲ್ಲಿ 500 ಮಿಮೀ ಕೇಂದ್ರಗಳು | Stainless, pressed | For lacing to a frame or to a second panel |
| D-ring / delta ring | Ø 12 ಮಿಮೀ, 60 × 110 ಮಿಮೀ | Zinc-plated or AISI 316 | Where a ratchet tensioner is used instead of a turnbuckle |
| ಟೆನ್ಷನರ್ | M12 turnbuckle, ಅಥವಾ 50 mm ratchet tensioner | Galvanised / zinc-plated | Take the slack out and stop; over-tensioning creeps the knots |
| Anchor post | Ø 60 × 3.0 mm or Ø 76 × 3.0 mm tube, 3–6 m | Hot-dip galvanised | Base plate 200 × 200 × 10 ಮಿಮೀ, 4 × M16; post size to be confirmed against design wind |
| Wall / anchor plate | 150 × 150 × 8 ಮಿಮೀ, 4 × M12 | Hot-dip galvanised | For fixing to concrete or steel structure |
| Stand-off bracket | 300 / 500 / 1000 mm arm | Galvanised | Keeps 1 m clear behind the panel for a caught aircraft to deform into |
| Eye bolt | M12 × 120 ಮಿಮೀ | Galvanised | Anchor point at the post or wall |
| Wire rope clip set | M6 / M8 with thimble | Galvanised | For anchor tails and temporary fixings |
| Wear sleeve | 500 ಮಿಮೀ, open tubular | PU-coated polyester | Where the panel crosses structure or a sharp edge |
| Repair kit | 3 m matching braid + splicing fid | ಅರಾಮಿಡ್ | One damaged mesh is re-knotted on site and recorded |
| Panel tag | 60 × 120 ಮಿಮೀ | Woven polyester | ಪ್ಯಾನಲ್ ಗಾತ್ರ, rope, ಜಾಲರಿ, ಫೈಬರ್, ಬ್ಯಾಚ್ ಸಂಖ್ಯೆ |
ಟೇಬಲ್ 2 — Fittings supplied with a standard opening. Load ratings of anchors and tensioners are confirmed against the panel design on the approval drawing.
Aramid against steel wire mesh
Steel wire mesh is the barrier most buyers compare against, and the comparison is usually made on the wire. It should be made on the joint. A clamped stainless mesh is pressed together with aluminium double ferrules, one at every crossing, and the ferrule — not the wire — sets the limit of the panel.
The following is the specification the steel mesh trade works to, translated from the Chinese original supplied with the material.
| Rope Ø (ಮಿಮೀ) | Strand | Ferrule joint, min. breaking force | ಕೆಎನ್ | ಟನ್‌ಗಳು |
|---|---|---|---|---|
| 1.2 | 7 × 7 | not published for mesh joints | - | - |
| 1.5 | 7 × 7 | ≈41 kgf (≈400 N) | 0.4 | 0.04 |
| 1.6 | 7 × 7 | not published for mesh joints | - | - |
| 2.0 | 7 × 7 | ≈265 kgf | 2.6 | 0.27 |
| 2.4 (3/32″) | 7 × 7 | ≈426 kgf (4.18 ಕೆಎನ್) | 4.18 | 0.43 |
| 3.0 | 7 × 19 | ≈552 kgf | 5.4 | 0.55 |
| 4.0 | 7 × 19 | ≈981 kgf | 9.6 | 0.98 |
| 6 / 8 / 10 / 12 | 7 × 19 | no ferrule rating published for mesh joints | - | - |
ಟೇಬಲ್ 3 — Stainless steel wire rope mesh, aluminium double ferrule to DIN EN 13411-3, SUS 304 / 304ಎಲ್ / 316 / 316ಎಲ್. Ferrule joints must not be bent again or re-used after pressing; for dynamic, impact or personnel duty the working load is taken as 1/5 ಗೆ 1/6 of the breaking force.
Steel wire mesh: a pressed aluminium ferrule at every crossing. The largest standard ferrule breaks at about 0.98 t — and that joint repeats across the whole panel.
Put the two tables side by side and the difference is not marginal.
| Element | Breaking force | Against the 4.0 mm ferrule |
|---|---|---|
| 10 mm aramid rope, knotted | 7 ಟಿ (≈68.6 kN) | 7.1 × |
| 10 mm aramid, ನಲ್ಲಿ 50 % knot efficiency | ≈3.6 t (35 ಕೆಎನ್) | 3.7 × |
| 6 mm aramid rope, knotted | 2.6 ಟಿ (≈25.5 kN) | 2.7 × |
| 4.0 mm steel wire + aluminium ferrule | 0.98 ಟಿ (9.6 ಕೆಎನ್) | 1.0 × |
| 3.0 mm steel wire + aluminium ferrule | 0.55 ಟಿ (5.4 ಕೆಎನ್) | 0.56 × |
ಟೇಬಲ್ 4 — Like for like: one element of net against one element of net.
Even the lightest rope we put in an anti-drone panel — 6 ಮಿಮೀ, 2.6 t — carries 2.7 times the load of the heaviest ferrule in the steel table, and it does so at roughly a tenth of the weight per square metre. The gap matters for a second reason: a steel mesh repeats its weakest joint hundreds of times across an opening, so a drone finds the nearest one, while a knotted panel spreads the impact through neighbouring meshes and degrades instead of unzipping.
Steel mesh is still the right answer for rigid screens, heavy debris and abrasion, and we make wire rope assemblies on the same presses — see ತಂತಿ ಹಗ್ಗ ಜೋಲಿಗಳು. It is not the right answer for a fast, light aircraft, because the ferrule sets the limit at about a tonne.
Choosing rope and mesh
Two decisions, ಈ ಕ್ರಮದಲ್ಲಿ: what has to be stopped, then what has to be seen through.
| Situation | ಹಗ್ಗ | ಜಾಲರಿ | ಏಕೆ |
|---|---|---|---|
| Perimeter screening, prisons, schools, events | 6 ಮಿಮೀ | 60–80 mm | ಬೆಳಕು, low wind area, deployable by two people; the threat is a small multirotor or a contraband drop |
| ಉಪಕೇಂದ್ರಗಳು, data centres, fuel points | 10 ಮಿಮೀ | 80–100 ಮಿ.ಮೀ | Real kinetic impact and a dropped payload; needs the joint strength and the fire behaviour |
| ಸಂಸ್ಕರಣಾಗಾರಗಳು, tank farms, hot process areas | 10 ಮಿಮೀ | 80–100 ಮಿ.ಮೀ | Panel must not melt or drip; aramid carbonises and holds its geometry |
| Airfields, helipads, approach zones | 10 ಮಿಮೀ | 100–120 mm | Larger airframes; wind load usually governs the anchors rather than the aircraft |
| Fine screens, sparks, small debris | 6 ಮಿಮೀ | 40–50 mm | Aperture smaller than the smallest part that must not pass |
ಟೇಬಲ್ 5 — Selection guide. Where the fire case governs rather than the impact, ನೋಡಿ ಬೆಂಕಿ ತಡೆಗಟ್ಟುವಿಕೆ ವಿರೋಧಿ ಡ್ರೋನ್ ಜಾಲರಿ.
Installation and stand-off
- ಸ್ಟ್ಯಾಂಡ್-ಆಫ್. Keep at least 1 m clear behind the panel. A caught aircraft has to deform into space, not into the asset.
- ಆಂಕರ್ ಅಂತರ. 2 ಮೀ ಅಥವಾ ಗಡಿಯ ಉದ್ದಕ್ಕೂ ಹತ್ತಿರದಲ್ಲಿದೆ. The border spans between anchors and carries everything the panel collects.
- ಉದ್ವೇಗ. Take the slack out and stop. A knotted aramid panel sets under its first load; over-tensioning creeps the knots and works the anchors loose.
- ರೂಫ್ ರಿಟರ್ನ್. A vertical wall can be flown over. Anything above about 6 m needs a return or a top curtain.
- No cut mesh. Never cut an aperture for access or a service. Put a reinforced opening on the drawing.
- ಗಾಳಿ. ಎ 100 ಮಿಮೀ ನಿವ್ವಳ ಸರಿಸುಮಾರು 30 % ಘನ; ಸ್ಥಳೀಯ ಮೂಲ ಗಾಳಿಯ ಒತ್ತಡದಲ್ಲಿ ಫಲಕವನ್ನು ಸರಂಧ್ರ ಮೇಲ್ಮೈಯಾಗಿ ಲೆಕ್ಕಹಾಕಿ, and size the posts to that, not to the drone.
ಗುರುತು ಹಾಕುವುದು, packing and documents
Each panel is rolled, strapped and tagged, with the tag carrying panel size, ಹಗ್ಗದ ವ್ಯಾಸ, ಜಾಲರಿ, ಫೈಬರ್ ಮತ್ತು ಬ್ಯಾಚ್ ಸಂಖ್ಯೆ. Panels travel in a PVC bag inside a woven outer, or on a pallet for multi-panel orders. Batch test records, a packing list and a declaration of conformity are supplied with the shipment; state the standard your site or customs authority needs and the documents are prepared to it.
ಎಚ್ಎಸ್ ಕೋಡ್ 630790. ಮೂಲ: ಲಿಫ್ಟ್ ಸ್ಲಿಂಗ್ ರಿಗ್ಗಿಂಗ್ ಕಂ., ಲಿಮಿಟೆಡ್, ಲೈಫ್ಯೂಟ್ ಇಂಡಸ್ಟ್ರಿಯಲ್ ಪಾರ್ಕ್, ತೈಝೌ ನಗರ, ಜಿಯಾಂಗ್ಸು ಪ್ರಾಂತ್ಯ, ಚೀನಾ.
Questions buyers ask
How strong is an aramid anti-drone net against a steel wire mesh?
ಎ 6 mm aramid rope breaks at 2.6 t and a 10 ಮಿಮೀ ನಲ್ಲಿ 7 ಟಿ. The largest standard ferrule on steel wire mesh — 4.0 mm rope — breaks at 981 kgf, ಸುಮಾರು 0.98 ಟಿ. On joint strength the 10 mm aramid element carries about seven times the best steel mesh joint, and even the 6 mm element carries 2.7 times as much.
What mesh size do I specify?
40–60 mm for small multirotors, so a propeller blade cannot pass; 80–100 mm for larger multirotors and fixed-wing airframes; 120 mm where panel weight and wind area matter more than aperture. The rule is that the aperture must be smaller than the part that would arrive first, measured between rope centres unless a clear opening is specified.
Is it a panel or a complete assembly?
A complete assembly: knotted panel, spliced border, corner eyes with stainless thimbles, edge eyelets where specified, tensioners and anchors, tagged and documented. Panels can be supplied loose where you already have the anchors and only need the net.
Will it stop a drone carrying a munition?
The net stops the delivery, not the warhead, and that is the whole point of netting a position. ಎ 5 kg munition arriving at 100 m/s is arrested with about 62.5 kN if it is stopped over 0.4 ಮೀ; shared across the four ropes of an engaged mesh that is roughly 16 kN per rope, against about 34 kN carried by a knotted 10 mm element even at 50 % knot efficiency. Break the delivery and the warhead never arrives.
Can a damaged panel be repaired on site?
Yes on knotted construction. One damaged mesh is re-knotted with the same braid and the repair is recorded. ಹಾನಿಗೊಳಗಾದ ಗಡಿ ಹಗ್ಗ, a pulled corner eye or a large damaged area is replaced rather than patched.
Does the net need power or detection?
ಸಂ. It is a passive physical barrier: no power, no radar, no operator. That is also why it still works against fibre-optic and pre-programmed drones that electronic countermeasures cannot reach.
ಸಂಬಂಧಿತ ಉತ್ಪನ್ನಗಳು
- High strength anti-drone rope net — the engineering behind the knot, the braid and the joint
- ಗಂಟುಗಳೊಂದಿಗೆ ಅರಾಮಿಡ್ ನಿವ್ವಳ — construction options and strength per braid
- ಬೆಂಕಿ ತಡೆಗಟ್ಟುವಿಕೆ ವಿರೋಧಿ ಡ್ರೋನ್ ಜಾಲರಿ — where flame, not impact, governs the fibre
- Durable safety netting for fall protection — the same netting tradition where a person has to be caught
- Safety rope nets — the full category, with panels, ಮೆಶ್ಗಳು ಮತ್ತು ಅಂಚಿನ ವಿವರಗಳು
- ನೈಲಾನ್ ಹಗ್ಗ and braided aramid rope — the line our panels are knotted from
ತೆರೆಯುವಿಕೆಯನ್ನು ಕಳುಹಿಸಿ, get a panel you can install
Tell us the width and height of the opening, what the panel fixes to and at what spacing, the stand-off behind it, the aircraft you are designing against and the design wind speed. We come back with rope diameter, ಜಾಲರಿ, border specification, fittings list and price — with the breaking force at the knot, ರೀಲ್‌ನಲ್ಲಿ ಮಾತ್ರವಲ್ಲ.
ಇಮೇಲ್ : lift98@jslift.com· Telephone and WeChat +8618066002268