Lift Sling Riging კომპანია აწარმოებს Heavy Duty-ს 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,
მძიმე მოვალეობა 20 Ton Polyester Cargo Lifting Net
ა 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

We build these nets to order in Taizhou: band width and layer, ბადე, წმინდა ზომა, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.
Why polyester at this rating
ზე 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.
| პოლიესტერი (PET) | ნეილონი (PA) | |
|---|---|---|
| Stretch under a steady load | Low — the net stays square and the load stays level | Markedly higher; the net settles and the load can tilt |
| შოკის შთანთქმა | ზომიერი | Best in the family; 18–22 % დრეკადობა შესვენებისას |
| წყლის შთანთქმა | ძალიან დაბალი, dries quickly | შესახებ 4 %, with some strength loss when saturated |
| Repetitive crane cycles | The usual choice | Better where pickups are rough |
| სამუშაო ტემპერატურა | -40 °C-მდე +100 °C | Lower at the top end |
| Best fit for a 20 ტ დატვირთვა | ჩანთიანი, პალეტირებული, bundled or stacked cargo lifted on a cycle | Irregular or shocky loads that must settle into the mesh |

What changes when the rating goes to 20 ტ
Capacity is not a property of the net’s size. It comes from four things moving together: ბენდი, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.
| Load band | Band and build | ბადე | ამწევი წერტილები | What else changes |
|---|---|---|---|---|
| 2 - 5 ტ | 50 mm single layer | 100 მმ | 4 corners | Standard warehouse net |
| 5 - 10 ტ | 50 - 75 მმ, duplex on the load run | 100 მმ | 4 corners, 8 მოთხოვნით | Heavier border, reinforced loops |
| 10 - 20 ტ | 75 - 100 მმ დუპლექსი | 100 - 150 მმ | 8 points | Master ring or spreader beam; net built to drawing |
| 20 - 30 ტ | 100 მმ დუპლექსი, band count from the load face | 150 მმ | 8 points | Spreader beam in the assembly; proof test per net |
| ზემოთ 30 ტ | 100 mm multi-layer or wider pitch | 150 - 200 მმ | 8 points or more | Engineered and tested to the lift, not to a catalogue |
Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.
ორი შედეგი მოჰყვება. პირველი, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 თ ა 10 t ring is a 10 t შეკრება. მეორე, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Sizing the net to a 20 ტ დატვირთვა
A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.
- Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. ა 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
- ჩანთის ფორმა: the flat width has to wrap up the sides and close over the top, ისე ბრტყელი სიგანე = კვალი + 2 × bag depth. ა 1.2 m footprint in a 0.6 m deep bag needs about 2.4 მ.
- Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.

ბადე: sized from the cargo, არა ტონაჟი
Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.
| ტვირთის ყველაზე მცირე განზომილება | Typical cargo at 20 ტ | Mesh დასაზუსტებლად |
|---|---|---|
| ქვეშ 75 მმ | მცირე კასტინგები, კომპონენტები ნაყარი, drummed goods | 100 მმ ბრილიანტი, ან დახურული ჩანთის ბადე |
| 75 - 150 მმ | აგური, შეფუთული საქონელი, გაყოფილი ქვა | 100 - 150 მმ |
| 150 - 250 მმ | Sawn packs, bundled tube, მუყაოები, ჯართი | 150 - 200 მმ |
| დასრულდა 250 მმ | ბლოკები, დიდი ქვა, დანგრევის ნამსხვრევები | 200 - 300 მმ |
სპეციფიკაცია
| პარამეტრი | სპეციფიკაცია |
|---|---|
| ტიპი | ღია ბრტყელი გისოსები, ოთხი ან რვა აწევის წერტილი |
| ბენდის მასალა | 100 % მაღალი გამძლეობის პოლიესტერი (PET); nylon or UHMWPE on request |
| ზოლის სიგანე | 75 - 100 mm for this class |
| Band build | დუპლექსი (ორმაგი ფენა) on the load-bearing run, single layer elsewhere |
| ბადის გახსნა | 100 - 150 მმ; square standard, diamond on request |
| წმინდა ზომა | როგორც წესი 4.0 × 4.0 მ-მდე 6.0 × 6.0 მ, or to the load footprint |
| სამუშაო დატვირთვის ლიმიტი | 20,000 kg in the rated arrangement |
| უსაფრთხოების ფაქტორი | 7:1 - მინიმალური რღვევის დატვირთვა 140,000 კგ |
| საზღვარი და კუთხეები | Doubled border, კუთხეებში გაბმული; reinforced loops, four or eight |
| ფიტინგები | სამაგისტრო ბეჭედი ან კლასი 80 ბორკილები; spreader beam for eight-point lifts |
| მკურნალობა | UV სტაბილიზირებულია, დაბერების საწინააღმდეგო, abrasion-resistant finish |
| სამუშაო ტემპერატურა | -40 °C-მდე +100 °C |
| მარკირება | WLL, arrangement, net size and identification on a sewn label; band printing on request |
| დოკუმენტაცია | Capacity label, მასალის ტესტის ანგარიში, CE მარკირება; ტესტირება ჩვენს მიერ 1000 t bed |
| HS კოდი | 630790 |

Eight points, ოთხი არა, once the load is long
Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.
- Four points suit square, compact loads where the net is only holding the cargo together;
- Eight points suit long or wide loads, and any lift where the net must stay flat under load;
- The spreader or master link, the slings above it and the hook must each be rated at least 20 ტ;
- Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.
The leg sees more than the share: ზე 45 deg from the vertical, ა 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.
Inspection and retirement
| შეამოწმეთ | გადადგომა ან შეკეთება თუ |
|---|---|
| Corner loops and their stitching | A loop is deformed, the stitching is broken, or the band is cut at the throat |
| საზღვარი | საზღვარი გაჭრილია, flattened, or has pulled out of a corner |
| Load-bearing bands | Any band is cut, ღრმად გახეხილი, heat glazed or chemically stained |
| Mesh geometry | The lattice is distorted from an overload — the net no longer sits square |
| ნაკერი | Stitch lines are broken or pulled at a crossover |
| Label and printing | The WLL or the arrangement is illegible — an unlabelled net cannot be rated |
Inspect before each lift and have the net examined by a competent person at the interval your site sets. შეინახეთ სუფთა და მშრალ მდგომარეობაში, მიწიდან და პირდაპირი მზისგან; never knot, weld or heat-repair a webbing net.

How it is built, and how the rating is proven
- Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
- Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
- Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
- Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.
იგივე ნამუშევრები ქსოვს ბადეებს და აჭერს მავთულხლართებს, which is why a net, ა ვეებერთელა სლინგი და ა მავთულის თოკი on the same lift can be matched in rating rather than bought from three suppliers.
სადაც ა 20 t net does the work
| სექტორი | რასაც ბადე აწევს | ჩვეულებრივი აშენება |
|---|---|---|
| ფოლადი და წარმოება | ჩალიჩები, სექციები, დასასვენებელი დატვირთვები | ბრტყელი ბადე, 100 მმ დუპლექსი, eight points |
| Stone and quarry | ბლოკები, გაყოფილი ქვა, რიყის | ჩანთის ფორმა, 150 მმ ბადე, კუთხის ლაქები |
| პორტები და ტერმინალები | Bagged and unitised cargo, quay work | Flat net on a spreader, დაბეჭდილი WLL |
| ხე-ტყე | Sawn packs, ბოძები, sleepers | Flat or bag, 150 - 200 მმ ბადე |
| ჯართი და გადამუშავება | შერეული და აბრაზიული ჯართი | დიდი ბადე, wear bands at the corners |
| ასაწყობი ბეტონი | Units, ბეჭდები, პანელები | Flat net with edge sleeves, eight points |
ხშირად ეკითხებოდა
არის 20 t rating for the net or for the whole assembly?
The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, ბორკილები, spreader and slings above must be rated at least 20 t as well.
Why is the safety factor 7:1 და არა 5:1?
7:1 is the factor we build to for this class, which gives a 140 t მინიმალური რღვევის დატვირთვა a 20 t რეიტინგი. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.
Polyester or nylon for a 20 ტ ლიფტი?
Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.
How big a net do I need for a 2 × 2 m load?
At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.
Can it be lifted by a single hook?
Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.
Can you print our brand and the WLL on the net?
Yes — WLL, arrangement, წმინდა ზომა, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.
მოითხოვეთ ციტატა
Send the load and how it is presented
The cargo — what it is, როგორ არის შეფუთული, and the weight as presented for the lift;
The footprint — length × width, plus height if a bag form is needed;
The lift — four or eight points, კაკლის სიმაღლე, and whether a spreader beam is available;
The duty — how many lifts a week, indoors or on a quay, and the temperature range;
The paperwork — CE marking, test report and own-brand printing if you need them.
სად წავიდეთ შემდეგ
- Webbing cargo lifting net — the standard 2–10 t range;
- Heavy duty nylon flat webbing net — the same lattice in nylon;
- ნეილონის თოკის ტვირთის ამწევი ბადე — rope construction to 50 ტ;
- Heavy duty cargo net sling — closed bottom for loose cargo;
- გამავრცელებელი სხივების ამწევი for eight-point lifts;
- The whole cargo lifting net range და contact.