Lift sling rigging company produce Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,
Servizio pesante 20 Ton Polyester Cargo Lifting Net
UN 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

We build these nets to order in Taizhou: band width and layer, maglia, dimensione netta, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.
Why polyester at this rating
A 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.
| Poliestere (ANIMALE DOMESTICO) | Nylon (PA) | |
|---|---|---|
| Stretch under a steady load | Low — the net stays square and the load stays level | Markedly higher; the net settles and the load can tilt |
| Assorbimento degli urti | Moderare | Best in the family; 18–22 % allungamento a rottura |
| Assorbimento d'acqua | Molto basso, dries quickly | Di 4 %, with some strength loss when saturated |
| Repetitive crane cycles | The usual choice | Better where pickups are rough |
| Temperatura di lavoro | Da −40 °C a +100 °C | Lower at the top end |
| Best fit for a 20 caricare | Insaccato, pallettizzato, bundled or stacked cargo lifted on a cycle | Irregular or shocky loads that must settle into the mesh |

What changes when the rating goes to 20 T
Capacity is not a property of the net’s size. It comes from four things moving together: la banda, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.
| Load band | Band and build | Maglia | Punti di sollevamento | What else changes |
|---|---|---|---|---|
| 2 – 5 T | 50 mm single layer | 100 mm | 4 corners | Standard warehouse net |
| 5 – 10 T | 50 – 75 mm, duplex on the load run | 100 mm | 4 corners, 8 su richiesta | Heavier border, reinforced loops |
| 10 – 20 T | 75 – 100 duplex da mm | 100 – 150 mm | 8 points | Master ring or spreader beam; net built to drawing |
| 20 – 30 T | 100 duplex da mm, band count from the load face | 150 mm | 8 points | Spreader beam in the assembly; proof test per net |
| Sopra 30 T | 100 mm multi-layer or wider pitch | 150 – 200 mm | 8 points or more | Engineered and tested to the lift, not to a catalogue |
Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.
Ne conseguono due conseguenze. Primo, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 t su a 10 t ring is a 10 tassemblaggio. Secondo, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Sizing the net to a 20 caricare
A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.
- Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. UN 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
- Forma di borsa: the flat width has to wrap up the sides and close over the top, COSÌ flat width = footprint + 2 × bag depth. UN 1.2 m footprint in a 0.6 m deep bag needs about 2.4 m across.
- Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.

Maglia: dimensionato dal carico, non la stazza
Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.
| Dimensione del carico più piccola | Typical cargo at 20 T | Maglia da specificare |
|---|---|---|
| Sotto 75 mm | Small castings, componenti alla rinfusa, drummed goods | 100 mm diamond, or a closed bag net |
| 75 – 150 mm | Mattoni, bagged goods, pietra spaccata | 100 – 150 mm |
| 150 – 250 mm | Sawn packs, bundled tube, cartoni, rottame | 150 – 200 mm |
| Sopra 250 mm | Blocchi, large stone, detriti della demolizione | 200 – 300 mm |
Specifica
| Parametro | Specifica |
|---|---|
| Tipo | Open flat webbing lattice, four or eight lifting points |
| Materiale del cinturino | 100 % poliestere ad alta tenacità (ANIMALE DOMESTICO); nylon or UHMWPE on request |
| Larghezza della banda | 75 – 100 mm for this class |
| Band build | Duplex (doppio strato) on the load-bearing run, single layer elsewhere |
| Apertura a rete | 100 – 150 mm; square standard, diamond on request |
| Dimensione netta | Tipicamente 4.0 × 4.0 m a 6.0 × 6.0 M, or to the load footprint |
| Limite del carico di lavoro | 20,000 kg in the rated arrangement |
| Fattore di sicurezza | 7:1 — carico di rottura minimo 140,000 kg |
| Bordo e angoli | Doubled border, giuntato negli angoli; reinforced loops, four or eight |
| Raccordi | Master ring or grade 80 catene; spreader beam for eight-point lifts |
| Trattamento | Stabilizzato ai raggi UV, anti-invecchiamento, abrasion-resistant finish |
| Temperatura di lavoro | Da −40 °C a +100 °C |
| Marcatura | WLL, arrangement, net size and identification on a sewn label; band printing on request |
| Documentazione | Capacity label, material test report, Marcatura CE; tested on our own 1000 t bed |
| Codice SA | 630790 |

Eight points, non quattro, once the load is long
Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.
- Four points suit square, compact loads where the net is only holding the cargo together;
- Eight points suit long or wide loads, and any lift where the net must stay flat under load;
- The spreader or master link, the slings above it and the hook must each be rated at least 20 T;
- Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.
The leg sees more than the share: A 45 deg from the vertical, UN 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.
Inspection and retirement
| Controllo | Retire or repair if |
|---|---|
| Corner loops and their stitching | A loop is deformed, the stitching is broken, or the band is cut at the throat |
| Confine | The border is cut, flattened, or has pulled out of a corner |
| Load-bearing bands | Any band is cut, profondamente abraso, heat glazed or chemically stained |
| Mesh geometry | The lattice is distorted from an overload — the net no longer sits square |
| Cucitura | Stitch lines are broken or pulled at a crossover |
| Label and printing | The WLL or the arrangement is illegible — an unlabelled net cannot be rated |
Inspect before each lift and have the net examined by a competent person at the interval your site sets. Conservarlo pulito e asciutto, da terra e al riparo dal sole diretto; never knot, weld or heat-repair a webbing net.

Come è costruito, and how the rating is proven
- Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
- Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
- Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
- Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.
The same works weaves webbing and presses wire rope ferrules, which is why a net, UN fettuccia e un imbracatura in fune metallica on the same lift can be matched in rating rather than bought from three suppliers.
Dove a 20 t net does the work
| Settore | Ciò che la rete solleva | Costruzione abituale |
|---|---|---|
| Acciaio e fabbricazione | Fasci, sezioni, stillage loads | Rete piatta, 100 duplex da mm, eight points |
| Pietra e cava | Blocchi, pietra spaccata, cobbles | Forma di borsa, 150 maglia da mm, corner patches |
| Porti e terminal | Bagged and unitised cargo, quay work | Flat net on a spreader, WL stampato |
| Rivestire di legno | Sawn packs, poli, sleepers | Flat or bag, 150 – 200 maglia da mm |
| Rottame e riciclaggio | Rottami misti e abrasivi | Large mesh, wear bands at the corners |
| Precast concrete | Units, anelli, pannelli | Flat net with edge sleeves, eight points |
Chiesto frequentemente
È il 20 t rating for the net or for the whole assembly?
The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, catene, spreader and slings above must be rated at least 20 t as well.
Why is the safety factor 7:1 e non 5:1?
7:1 is the factor we build to for this class, which gives a 140 t carico di rottura minimo per a 20 valutazione t. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.
Polyester or nylon for a 20 t sollevare?
Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.
How big a net do I need for a 2 × 2 m load?
At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.
Can it be lifted by a single hook?
Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.
Can you print our brand and the WLL on the net?
Yes — WLL, arrangement, dimensione netta, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.
Richiedi un preventivo
Send the load and how it is presented
The cargo — what it is, come è imballato, and the weight as presented for the lift;
The footprint — length × width, plus height if a bag form is needed;
The lift — four or eight points, hook height, and whether a spreader beam is available;
The duty — how many lifts a week, indoors or on a quay, and the temperature range;
The paperwork — CE marking, test report and own-brand printing if you need them.
Dove andare dopo
- Rete di sollevamento merci in tessuto — the standard 2–10 t range;
- Heavy duty nylon flat webbing net — the same lattice in nylon;
- Rete di sollevamento carichi in corda di nylon — rope construction to 50 T;
- Heavy duty cargo net sling — closed bottom for loose cargo;
- Travi di sollevamento for eight-point lifts;
- The whole cargo lifting net range E contact.