Framleiða fyrirtæki með lyftistöngum 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet ól,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.
5 Ton Heavy Duty Ratchet Straps
50 mm pólýester vefjum, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 til 10 m sem staðalbúnaður, LC 2,500 Og, STF 350 og N kl 50 og handafli. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.
Part of the webbing slingur and lashing range. The 50 mm specification in isolation sits on the 50 mm 5000 kg spennubelti með skralli síðu.
What “5 Ton” Actually Means on a Ratchet Strap
Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. Undir EN 12195-2 vefur festingarólar verður að ná að minnsta kosti tvöfaldri festingargetu sinni, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.
| Mynd | Value on the 50 mm assembly | Það sem það lýsir | How it gets misread |
|---|---|---|---|
| Lágmarksbrotstyrkur | 5,000 Og (5,000 kg) | Álagið sem samsetningin mistekst í togprófi | Read as the working figure — the mistake that overloads a trailer |
| Festingargeta (LC) | 2,500 Og (2.5 t) | Aðhaldið sem samsetningin er metin til að halda, printed on the label | Samanborið við WLL lyftistöng, which is a different duty altogether |
| Venjulegur spennukraftur (STF) | 350 og N kl 50 og handafli | The tension one person reaches with the ratchet handle | Er að rugla saman við LC, þannig að stjórnandinn heldur áfram að vinda framhjá gagnlega punktinum |
Hvers vegna 50 mm Build Is the Heavy-Duty Default
Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. The 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.
| Vefbreidd | Typical LC | Brotstyrkur | Fyrir hvað það er keypt |
|---|---|---|---|
| 25 mm (1 inn) | 400–500 daN | 800–1,000 daN | Tool boxes, light restraint, tight anchor eyes |
| 35 mm (1-3/8 inn) | 750 Og | 1,500 Og | Van and trailer decks, general cargo |
| 38 mm (1-1/2 inn) | 1,000–1,500 daN | 2,000–3,000 daN | Stálplata, pípubúnt, plant |
| 50 mm (2 inn) | 2,500 Og | 5,000 Og | Heavy cargo restraint, vafningum, vélar, gáma |
| 75-100 mm | 5,000 daN and up | 10,000 daN and up | Abnormal loads, where the bed allows the width |
The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.
Standard Specification of the 5 Ton Assembly
| Atriði | Forskrift |
|---|---|
| Vefgangur | 100% hárþéttni pólýester, twill vefnaður, UV stöðugt, 50 mm ± 2% |
| Bandþykkt / messa | 1.8 mm að nafnvirði / 88 g per metre |
| Festingargeta (LC) | 2,500 og á hverja samkomu |
| Lágmarksbrotstyrkur | 5,000 Og (2:1 against LC) |
| Venjulegur spennukraftur (STF) | 350 og N kl 50 og handafli |
| Strekkjari | Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle |
| Lenging við LC | 7% eða minna |
| Þjónustuhitastig | -40 °C til +100 °C (pólýester webbing) |
| Venjuleg lengd | 3-10 m; 1–30 m to order |
| Merking | Ofið merki: LC, STF, lengd, lotunúmer, standard reference |
| Standard | Designed, tested and marked to EN 12195-2 |
| HS kóða | 630790 |
The End Fitting Decides Whether the Strap Fits the Job
The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.
| Mátun | Anchors to | Notes before ordering |
|---|---|---|
| Chassis rave hook | Flatbed side rail, chassis lip | Check rail thickness and that the hook throat clears it |
| Claw hook | Anchor rings, D rings, recessed eyes | Opening must clear the ring; load on the crown only |
| D ring / delta hringur | Welded or bolted anchor points | Ring bore at least as wide as the webbing |
| Flat snap hook | E-braut, slotted rail, holur | Confirm slot width; snap gate must close fully |
| S hook | Pípur, teinar, frame members | Both ends must seat without point loading on a weld |
| Sewn loop / looped ends | Around the load or through a bore | Nothing metal at the load; ideal for finished surfaces |
| Endalaus, ekki passa | Girth only — hulls, vafningum, knippi | See the endless loop build below |

The 5 Ton Strap in Two Special Builds
Polyester covers most freight, and it fails predictably when it is out of its depth: það mýkist í kring 150 °C and melts at about 255 °C, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.
Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces
The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 eða 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 og N kl 25 mm til 2,500 og N kl 50 mm, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.
The grade decision is about chloride, ekki hlaða. 304 (1.4301) handles rain, fersku vatni, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 í þeirri trú að það sé sterkara er að borga fyrir ranga eign. Þar sem umsókn er öryggistengd, staðfesta einkunnina á mylluskírteininu frekar en á reikningslýsingunni.
Two shop-floor notes worth passing on. Ryðfríir þræðir gall, so a dry 316 hneta keyra hart á a 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. Og ryðfrítt boltað við ál í saltvatni myndar galvanískt par, so where the strap anchors to an alloy frame, einangra snertingu.
Full range and grade comparison: endless stainless steel ratchet strap.
Aramid (Kevlar) ratchet straps — for heat, sparks and cut edges
Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 °C. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.
The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.
Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.
How Many Straps Does the Load Actually Need?
Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.
| Straps used | Angle to the deck | Restraint per strap | Total restraint |
|---|---|---|---|
| 2 | 45° | ca. 1,750 Og | ca. 3,500 Og |
| 4 | 30° | ca. 1,250 Og | ca. 5,000 Og |
| 4 | 45° | ca. 1,750 Og | ca. 7,000 Og |
| 4 | 60° | ca. 2,165 Og | ca. 8,660 Og |
| 6 | 45° | ca. 1,750 Og | ca. 10,500 Og |
The arithmetic is an illustration, not a lashing plan: IN 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.
Þar sem 5 Ton Ratchet Strap Earns Its Keep
- Flatbed, container and plant trailer restraint — the volume application for the 50 mm build.
- Stálspóla, hella, billet and pipe bundles, with edge protection at the contact points.
- Vélar, moulds and skid-mounted plant, þar sem a 25 mm strap has neither the width nor the tension.
- Timburpakkar, grindur og stillingar, including the endless form that simply closes round the pack.
- Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
- Marine, marina and wash-down duty in 304 eða 316 where plated hardware would be a maintenance item.
- Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.

Litur, Printing and Private Label
Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, appelsínugult, gulur, svartur, rauður, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, lengd, standard and traceability code. Cartons of 10 til 20 stykki, palletised for export, with neutral or own-brand packaging as required.
Prófanir, Traceability and the Paperwork Buyers Ask For
Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. Test reports, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.
One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.
Algengar spurningar
Er a 5 ton ratchet strap rated to lift 5 tonn?
Nei, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.
Why does the same strap get called 5 tonn og 2.5 tonn?
Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.
50 mm eða 38 mm for a flatbed?
50 mm, unless the anchor points are small. The 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; the 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.
Do I need 304 eða 316 ryðfríu?
316 where chloride is present — sea air, saltúða, afísingarsalt, boatyards, food plants. 304 is enough for rain, fersku vatni, condensation and indoor wash-down. The difference is corrosion resistance, ekki styrk.
At what temperature does polyester fail, and what does aramid do instead?
Polyester softens around 150 °C and melts at about 255 °C, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 °C, and chars at about 427 °C instead of melting. Hér að ofan 400 °C, or against molten metal, both need a heat shield.
Can the strap be supplied with a printed brand and a custom length?
Já. Breiddar, lengdir til 30 m, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.
Óska eftir tilboði
Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, umhverfið (salt, hita, wash-down), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.
Lift Sling Rigging Company
Lifute iðnaðargarðurinn, Taizhou borg, Jiangsu héraði, Kína
Sími: +86 523 8693 5818 · WhatsApp: +86 180 6600 2268
Tölvupóstur: 702461526@qq.com · HS code 630790
Tengdar vörur
- Ratchet straps — the full lashing range, 25 mm til 100 mm.
- 50 mm 5000 kg spennubelti með skralli — this specification in detail.
- Endless loop ratchet strap — closed loop, enginn krókur, for girth-only loads.
- Endless stainless steel ratchet strap — 304 eða 316 for salt and wash-down.
- Aramid flame retardant ratchet straps — 200 °C samfellt, 400 °C hámarki.
- Pólýester webbing sling — when the job is lifting rather than lashing.

