Lift sling rigging company produce Aramid Anti-Drone Nets,knotted Aramid Anti-Drone Net,high strength Anti-Drone Net,Aramid Anti-Drone Net for Restricted Area Protection,Para Aramid Safety Net,Heavy Duty Aramid Fabric Netting for Anti-Drone Defense/Perimeter Protection/Security Facilities.
A aramid anti-drone net is a knotted rope panel hung across the line a small unmanned aircraft would fly through. We supply it as a complete assembly rather than a loose piece of netting: knotted aramid panel, spliced border, anya nkuku, tensioners and anchors, quoted per opening so that the panel, the border and the fixings carry the same load.
Two rope sizes cover almost every installation. A 6 mm braided aramid rope breaks at 2.6 t and is the panel for perimeter work, prisons, schools and anywhere the aperture has to be fine without the panel becoming heavy. A 10 mm braided aramid rope breaks at 7 t and is the panel for real kinetic impact — refineries, substations, ọdụ ụgbọ mmiri, airfields. Both are knotted, both are spliced into the border, and both are supplied with the fittings that take the load out of the mesh and into the structure.
At a glance
- 6 mm braided aramid rope — breaking force 2.6 t
- 10 mm braided aramid rope — breaking force 7 t (70.67 kN measured on a 10 mm sample)
- Knotted mesh 40–120 mm, panel ka 10 × 20 m
- Supplied with border, anya nkuku, tensioners and anchors
- No power, no radar, no operator — passive interception
- Adịghị agbaze: carbonises sitere na ihe 400 Celsius C ma jide udi ya
On this page
What the assembly is made of
Four elements decide whether the barrier works, na naanị otu n'ime ha bụ eriri.
- The panel. A 12-strand braided aramid rope, double-knotted into square or diamond mesh. The knot gathers four rope ends, so the load entering from one direction leaves through the other three instead of passing through a clamp.
- Oke oke. The same braid or one size up, double-laid and spliced — never knotted — around the perimeter. The border collects everything the mesh gathers and hands it to the corner eyes.
- The corner eyes and fixing points. Spliced eyes with stainless thimbles at the corners, eyelets or D-rings along the edge at your anchor spacing.
- The arịlịka. Posts, wall plates or stand-off brackets. A panel that is strong enough and tied to a post that is not will fail at the post.
The construction detail behind the knot, the braid and the fire behaviour is set out on the high strength anti-drone rope net ibe; this page carries the specification and the fittings you need to place an order.
Usoro nka
The figures below are the manufacturing range. The batch certificate supplied with the panel governs, and the installed barrier is only as strong as its border and anchors.
| Ihe | Aramid anti-drone net — standard build |
|---|---|
| Fiber | Para-aramid (Ụdị Kevlar), UV kwụsiri ike; polyester available for light duty |
| Ịrụ eriri | 12-eriri eriri, coreless; 8-strand on 6 mm and below |
| Dayameta eriri | 6 mm na 10 mm ọkọlọtọ; 4 / 8 / 12 mm ịtụ |
| Breaking force — 6 mm | 2.6 t (≈25.5 kN) |
| Breaking force — 10 mm | 7 t (≈68.6 kN; 70.67 kN measured on sample Dia10mm, 23 June 2026) |
| Ogologo oge | ≈3.5 % na nkwụsịtụ; n'okpuru 1.5 % na ibu ọrụ |
| Ntupu | 40 / 50 / 60 / 80 / 100 / 120 mm, square ma ọ bụ diamond |
| Ihe owuwu | Ejikọtara ọnụ, double knot hand-set and locked |
| Nha panel | 5 × 10 m, 10 × 10 m, 10 × 20 m dị ka otu panel; nnukwu oghere dị ka akụkụ jikọtara ọnụ |
| Ibu | ≈1.6 kg/m² at 10 mm / 100 mm ntupu; ≈0.6 kg/m² at 6 mm / 100 mm |
| Thermal | Enweghị ebe mgbaze na ọrụ; continuous to ≈200 °C; carbonises from ≈400 °C |
| Agba | Eke aramid ọla edo, nwa, ma ọ bụ ịtụ |
| Mkpuchi | Ekpuchighị, ma ọ bụ PU / neoprene tinye maka UV na abrasion na paịlị mpụga na-adịgide adịgide |
| Ịka akara | Mkpado nwere nha panel, dayameta eriri, ntupu, eriri na batch nọmba |
| Ọrụ | Physical interception — never fall arrest, anaghị ebuli |
Tebụl 1 — Aramid anti-drone net, ọkọlọtọ ewu.
Oke, fittings and anchor schedule
Buyers rarely fail on the panel and often fail on what it is tied to. The schedule below is what we supply with a standard opening; every line is confirmed on the approval drawing before the panel is woven.
| Ihe | Nkọwapụta | Ihe onwunwe / imecha | Ihe ndetu |
|---|---|---|---|
| Ụdọ oke ala | 10 mm 12-strand aramid, okpukpu abụọ, gbawara agbawa | Aramid, optional PU dip | Never knotted — a knot in the border puts the panel through a single joint at its most loaded point |
| Corner eye | 80 × 160 mm spliced eye, stainless thimble | AISI 316 timble | One per corner as standard; extra eyes on long spans |
| Edge eyelets | Ø 12 mm, na 500 ebe mm | Stainless, pressed | For lacing to a frame or to a second panel |
| D-ring / delta ring | Ø 12 mm, 60 × 110 mm | Zinc-plated or AISI 316 | Where a ratchet tensioner is used instead of a turnbuckle |
| Tensioner | M12 turnbuckle, ma ọ bụ 50 mm ratchet tensioner | Galvanised / zinc-plated | Take the slack out and stop; over-tensioning creeps the knots |
| Anchor post | Ø 60 × 3.0 mm or Ø 76 × 3.0 mm tube, 3–6 m | galvanized na-ekpo ọkụ | Base plate 200 × 200 × 10 mm, 4 × M16; post size to be confirmed against design wind |
| Wall / anchor plate | 150 × 150 × 8 mm, 4 × M12 | galvanized na-ekpo ọkụ | For fixing to concrete or steel structure |
| Stand-off bracket | 300 / 500 / 1000 mm arm | Galvanised | Keeps 1 m clear behind the panel for a caught aircraft to deform into |
| Eye bolt | M12 × 120 mm | Galvanised | Anchor point at the post or wall |
| Wire rope clip set | M6 / M8 with thimble | Galvanised | For anchor tails and temporary fixings |
| Wear sleeve | 500 mm, open tubular | PU-coated polyester | Where the panel crosses structure or a sharp edge |
| Repair kit | 3 m matching braid + splicing fid | Aramid | One damaged mesh is re-knotted on site and recorded |
| Panel tag | 60 × 120 mm | Woven polyester | Nha panel, rope, ntupu, eriri, nọmba ogbe |
Tebụl 2 — Fittings supplied with a standard opening. Load ratings of anchors and tensioners are confirmed against the panel design on the approval drawing.
Aramid against steel wire mesh
Steel wire mesh is the barrier most buyers compare against, and the comparison is usually made on the wire. It should be made on the joint. A clamped stainless mesh is pressed together with aluminium double ferrules, one at every crossing, and the ferrule — not the wire — sets the limit of the panel.
The following is the specification the steel mesh trade works to, translated from the Chinese original supplied with the material.
| Ụdọ Ø (mm) | Strand | Ferrule joint, min. breaking force | kN | Tọn |
|---|---|---|---|---|
| 1.2 | 7 × 7 | not published for mesh joints | - | - |
| 1.5 | 7 × 7 | ≈41 kgf (≈400 N) | 0.4 | 0.04 |
| 1.6 | 7 × 7 | not published for mesh joints | - | - |
| 2.0 | 7 × 7 | ≈265 kgf | 2.6 | 0.27 |
| 2.4 (3/32″) | 7 × 7 | ≈426 kgf (4.18 kN) | 4.18 | 0.43 |
| 3.0 | 7 × 19 | ≈552 kgf | 5.4 | 0.55 |
| 4.0 | 7 × 19 | ≈981 kgf | 9.6 | 0.98 |
| 6 / 8 / 10 / 12 | 7 × 19 | no ferrule rating published for mesh joints | - | - |
Tebụl 3 — Stainless steel wire rope mesh, aluminium double ferrule to DIN EN 13411-3, SUS 304 / 304L / 316 / 316L. Ferrule joints must not be bent again or re-used after pressing; for dynamic, impact or personnel duty the working load is taken as 1/5 ka 1/6 of the breaking force.
Steel wire mesh: a pressed aluminium ferrule at every crossing. The largest standard ferrule breaks at about 0.98 t — and that joint repeats across the whole panel.
Put the two tables side by side and the difference is not marginal.
| Element | Breaking force | Against the 4.0 mm ferrule |
|---|---|---|
| 10 mm aramid eriri, knotted | 7 t (≈68.6 kN) | 7.1 × |
| 10 mm aramid, na 50 % knot efficiency | ≈3.6 t (35 kN) | 3.7 × |
| 6 mm aramid eriri, knotted | 2.6 t (≈25.5 kN) | 2.7 × |
| 4.0 mm steel wire + aluminium ferrule | 0.98 t (9.6 kN) | 1.0 × |
| 3.0 mm steel wire + aluminium ferrule | 0.55 t (5.4 kN) | 0.56 × |
Tebụl 4 — Like for like: one element of net against one element of net.
Even the lightest rope we put in an anti-drone panel — 6 mm, 2.6 t — carries 2.7 times the load of the heaviest ferrule in the steel table, and it does so at roughly a tenth of the weight per square metre. The gap matters for a second reason: a steel mesh repeats its weakest joint hundreds of times across an opening, so a drone finds the nearest one, while a knotted panel spreads the impact through neighbouring meshes and degrades instead of unzipping.
Steel mesh is still the right answer for rigid screens, nnukwu irighiri ihe na abrasion, and we make wire rope assemblies on the same presses — see eriri eriri slings. It is not the right answer for a fast, ụgbọ elu dị mfe, because the ferrule sets the limit at about a tonne.
Choosing rope and mesh
Two decisions, n'usoro a: what has to be stopped, then what has to be seen through.
| Situation | Ụdọ | Ntupu | Ntak |
|---|---|---|---|
| Perimeter screening, prisons, schools, events | 6 mm | 60–80 mm | Ìhè, low wind area, deployable by two people; the threat is a small multirotor or a contraband drop |
| Substations, data centres, fuel points | 10 mm | 80-100 mm | Real kinetic impact and a dropped payload; needs the joint strength and the fire behaviour |
| Ụlọ nrụpụta, tank farms, hot process areas | 10 mm | 80-100 mm | Panel must not melt or drip; aramid carbonises and holds its geometry |
| Airfields, helipads, approach zones | 10 mm | 100–120 mm | Larger airframes; wind load usually governs the anchors rather than the aircraft |
| Fine screens, sparks, small debris | 6 mm | 40–50 mm | Aperture smaller than the smallest part that must not pass |
Tebụl 5 — Selection guide. Where the fire case governs rather than the impact, hụ mgbochi ọkụ mgbochi drone ntupu.
Installation and stand-off
- Akwụsịla. Keep at least 1 m doro anya n'azụ panel. A caught aircraft has to deform into space, not into the asset.
- Oghere arịlịka. 2 m ma ọ bụ nso n'akụkụ oke. The border spans between anchors and carries everything the panel collects.
- Tension. Take the slack out and stop. Otu panel aramid kekọtara na-edobe n'okpuru ibu nke mbụ ya; over-tensioning creeps the knots and works the anchors loose.
- Nlaghachi n'elu ụlọ. A vertical wall can be flown over. Anything above about 6 m chọrọ nloghachi ma ọ bụ ákwà mgbochi elu.
- No cut mesh. Never cut an aperture for access or a service. Put a reinforced opening on the drawing.
- Ifufe. A 100 mm net bụ roughly 30 % siri ike; gbakọọ panel ahụ dị ka oghere na-asọ oyi na ikuku ikuku nke mpaghara, and size the posts to that, not to the drone.
Ịka akara, packing and documents
Each panel is rolled, strapped and tagged, with the tag carrying panel size, dayameta eriri, ntupu, eriri na batch nọmba. Panels travel in a PVC bag inside a woven outer, or on a pallet for multi-panel orders. Batch test records, a packing list and a declaration of conformity are supplied with the shipment; state the standard your site or customs authority needs and the documents are prepared to it.
Koodu HS 630790. Mmalite: Ụlọ ọrụ Lift Sling Rigging Co., Ltd., Ltd, Ụlọ ọrụ Lifute Industrial Park, Obodo Taizhou, Jiangsu Province, China.
Questions buyers ask
How strong is an aramid anti-drone net against a steel wire mesh?
A 6 mm aramid rope breaks at 2.6 t and a 10 mm at 7 t. The largest standard ferrule on steel wire mesh — 4.0 mm rope — breaks at 981 kgf, gbasara 0.98 t. On joint strength the 10 mm aramid element carries about seven times the best steel mesh joint, and even the 6 mm element carries 2.7 times as much.
What mesh size do I specify?
40–60 mm for small multirotors, so a propeller blade cannot pass; 80–100 mm for larger multirotors and fixed-wing airframes; 120 mm where panel weight and wind area matter more than aperture. The rule is that the aperture must be smaller than the part that would arrive first, tụrụ n'etiti ebe eriri ma akọwapụtaghị oghere doro anya.
Is it a panel or a complete assembly?
A complete assembly: knotted panel, spliced border, corner eyes with stainless thimbles, edge eyelets where specified, tensioners and anchors, tagged and documented. Panels can be supplied loose where you already have the anchors and only need the net.
Will it stop a drone carrying a munition?
The net stops the delivery, not the warhead, and that is the whole point of netting a position. A 5 kg munition arriving at 100 m/s is arrested with about 62.5 kN if it is stopped over 0.4 m; shared across the four ropes of an engaged mesh that is roughly 16 kN per rope, against about 34 kN carried by a knotted 10 mm element even at 50 % knot efficiency. Break the delivery and the warhead never arrives.
Can a damaged panel be repaired on site?
Yes on knotted construction. One damaged mesh is re-knotted with the same braid and the repair is recorded. Ụdọ oke ala mebiri emebi, a pulled corner eye or a large damaged area is replaced rather than patched.
Does the net need power or detection?
Mba. It is a passive physical barrier: no power, no radar, no operator. That is also why it still works against fibre-optic and pre-programmed drones that electronic countermeasures cannot reach.
Ngwaahịa ndị emetụtara
- High strength anti-drone rope net — the engineering behind the knot, the braid and the joint
- Ụgbụ Aramid nwere eriri — construction options and strength per braid
- Mgbochi mgbochi drone ntupu — where flame, not impact, governs the fibre
- Durable safety netting for fall protection — the same netting tradition where a person has to be caught
- Ụgbụ ụdọ nchekwa — the full category, na panel, meshes na nsọtụ nkọwa
- eriri nylon and braided aramid rope — the line our panels are knotted from
Zipu oghere, get a panel you can install
Tell us the width and height of the opening, what the panel fixes to and at what spacing, the stand-off behind it, the aircraft you are designing against and the design wind speed. Anyị ji dayameta ụdọ laghachi, ntupu, border specification, fittings list and price — with the breaking force at the knot, ọ bụghị naanị na reel.
E-mail : lift98@jslift.com· Telephone and WeChat +8618066002268