Kategori pwodwi yo

Single Ply Endless Lifting Sling

Kout Deskripsyon:

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Single ply endless lifting sling: one layer, one lapped joint, pa gen fen. 4 mm bann, 1-12 t nan 7:1 de YON 1492-1, quoted by circumference or flat length.

Pwodwi detay

Lift sling rigging company produce Single Ply Endless Lifting Sling,Single Ply Endless Sling,single ply Endless webbing sling,Single-Ply Endless Flat Sling.

Endless lifting sling · single layer · 4 mm flat band

Single Ply Endless Lifting Sling

Yon kouch, one lapped joint, pa gen fen. The lightest closed loop in the range: it folds into a pocket, turns a tight radius and drapes over the load — 1 t pou 12 t nan 7:1 de YON 1492-1.

1–12 t single ply ladder 4 mm band section 7:1 de YON 1492-1 25-300 mm band lajè
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets

A single ply endless lifting sling is the single-layer build of the closed loop: one band of high-tenacity polyester, lapped over itself and closed with dense parallel rows of stitching, ki pa gen je, no fittings and no metal anywhere on the article. Li se alkole kalite A plat tise fistibal sangle nan EN 1492-1 — the type 5 web sling in North American usage.

The word to be careful with is ply. It does not mean two slings or two bands in parallel; it means how many layers of webbing are woven into the one band the loop is made from. Single ply is one layer, and everything that follows — the 4 mm section, the weight per metre, the way it turns round a small radius, and the capacity it can be given at a given width — comes from that one decision.

The trade-off in one line. Single ply gives the most flexible loop and the lowest weight per metre; duplex gives more capacity at the same width, a stiffer bearing face and more abrasion reserve. Anba sou 6 t, and wherever the loop has to fold, single ply is the right default.

What one layer actually gives you

Four practical differences separate the single-layer loop from the duplex build, and each one shows up on a different job:

  • A 4 mm section. The band folds into a pocket, coils onto a hook and passes between a load and a tight gap where a thicker band will not go.
  • Less weight per metre. The ladder below runs from 0.20 kg/m nan 1 t pou 2.05 kg/m nan 10 t — a one-handed carry for the sizes most yards actually use.
  • More supple over a radius. One layer conforms to pipe, tube and rolled sections instead of standing off them, so contact is over the full width rather than at two edges.
  • Yon jwenti, thin and easy to read. The lapped joint is the only made connection in the load path; in a single layer the stitching rows sit on one visible face, with no second layer masking them.
Single ply endless lifting sling in a basket hitch lifting a stack of steel sheets
Plate and sheet in a basket: one layer of band, doubled under the load, a full-width soft bearing face and no fitting anywhere near the steel.

Single ply against duplex, at the same width

The two builds are not two grades of the same thing; they are two answers to different questions. The comparison below is the one we use in quotation, and the widths are the published single-ply ladder.

Tablo 1 — Single ply and duplex, same nominal width
Single pli Duplex
Layers in the band Youn De, woven as one band
Section thickness 4 mm at the standard ladder Roughly twice the single-ply section
Capacity at a given width The ladder figure Higher — the reason duplex exists above the single-ply range
Pwa pou chak mèt 0.20 kg/m nan 1 t pou 2.05 kg/m nan 10 t Higher for the same width
Manyen Folds small, turns a tight radius, drapes onto the load Pi rèd; sits flatter over an edge and resists abrasion longer
Kote li genyen Anba sou 6 t, tight gaps, small diameters, mixed rigs High capacity in a narrow width, rough edges, heavy abrasion
Joint One lap, stitching visible on the face One lap through the doubled band

The duplex build has its own page: double ply endless lifting sling.

The capacity ladder, sèl pli

Working load limits are quoted in straight lift, nan 7:1 de YON 1492-1. Colour follows EN 1492-1 and is a capacity band, not a material; pi wo a 10 t there is no colour code and the label is the only rating.

Tablo 2 — Single ply endless sling: capacity, colour and weight
WLL, leve dwat Koulè Referans lajè Ranje longè Apeprè. pwa Toufe (× 0.8)
1 t Vyolèt Konfime sou lòd 0.5 – 100 m 0.22 kg/m 0.8 t
2 t Vèt 50 mm 1 – 100 m 0.35 kg/m 1.6 t
3 t Jòn 75 mm 1 – 100 m 0.52 kg/m 2.4 t
4 t Gri 100 mm 1.5 – 100 m 0.80 kg/m 3.2 t
5 t Wouj 125 mm 1.5 – 100 m 0.85 kg/m 4.0 t
6 t Brown 150 mm 1.5 – 100 m 0.96 kg/m 4.8 t
8 t Ble 200 mm 2 – 100 m 1.34 kg/m 6.4 t
10 t Orange 250 mm 2 – 100 m 1.64 kg/m 8.0 t
Anwo 10 t Pa gen kòd koulè Duplex build Pou kòmande Sou demann Label gouvène

Widths and weights are the published series for this range; the finished width, ply and weight are confirmed on the order acknowledgement.

Lajè, safety factor and the same capacity

A higher safety factor needs a wider band for the same working load limit, se poutèt sa kolòn lajè a gen twa valè. Tell us the standard your site works to and the sling is built to it; the figures below are the single-ply polyester ladder.

Tablo 3 — Band lajè pa faktè sekirite, 4 mm sèl pli Polyester
WLL Nan 5:1 Nan 6:1 Nan 7:1 Epesè Pwa nan 7:1
1 t (1 000 kg) 25 mm 25 mm 30 mm 4 mm 0.20 kg/m
2 t (2 000 kg) 50 mm 50 mm 60 mm 4 mm 0.60 kg/m
3 t (3 000 kg) 75 mm 75 mm 90 mm 4 mm 0.78 kg/m
4 t (4 000 kg) 100 mm 100 mm 120 mm 4 mm 0.90 kg/m
5 t (5 000 kg) 125 mm 125 mm 150 mm 4 mm 1.14 kg/m
6 t (6 000 kg) 150 mm 150 mm 180 mm 4 mm 1.33 kg/m
8 t (8 000 kg) 200 mm 200 mm 240 mm 4 mm 1.85 kg/m
10 t (10 000 kg) 250 mm 250 mm 300 mm 4 mm 2.05 kg/m
12 t (12 000 kg) 300 mm 300 mm 300 mm 4 mm 2.70 kg/m
Four single ply endless slings in white, vyolèt, green and black
The capacity colour is woven in, not printed on: white for the general band, violet for 1 t, green for 2 t, with one black transverse stripe per tonne as a second check.

Jwenti a, and why it is the first thing to look at

Yon fistibal kontinuèl se kontinuèl nan itilize, pa san pwoblèm. Se gwoup la lapped sou tèt li epi li fèmen ak ranje paralèl dans nan asanblaj; Wis sa a se yon jwenti plen fòs epi li chita nan chemen chaj la. Li se sèl koneksyon ki fèt nan atik la antye.

On a single-layer loop that joint is easier to inspect than on a duplex one, because the stitching rows lie on one visible face rather than between two layers. Look for broken or pulled stitches, a lap that has started to open, and abrasion where the lap passes over an edge. If the joint is sound, the rest of the loop is one continuous band and can be read anywhere along its length.

White single ply endless sling laid out on gravel
Yon bann, lapped and stitched once. That single joint is the only made connection in the load path, and the first thing an inspector reads.

Three hitches from the same loop

The marked figure is the straight-lift rating; every other arrangement is derived from it. Size the sling to the hitch the crew will actually rig, not to the one in the lift plan.

Tablo 4 — Mode factor by hitch
Attelage Faktè mòd Ki sa li vle di sou sit la
Vètikal × 1.0 The label figure applies directly
Toufe × 0.8 A 4 t chaje nan yon toufe bezwen yon 5 t sling — the wrap grips as the load comes on
Panyen, janm tou pre vètikal × 2.0 Both sides of the loop carry the load and the bearing face is doubled
Panyen, 7°–45° × 1.4 As the legs open the rating falls; plan the angle, not only the weight
Panyen, 45°–60° × 1.0 At wide angles the basket advantage is gone — treat it as a straight lift

Longè: sikonferans, or the height you actually get

Yon bouk fèmen pa gen okenn fen, donk pa gen anyen pou mezire bout pou bout. This trade quotes the same sling two ways, epi yo diferan pa apeprè yon faktè de: the circumference is the perimeter of the loop, while the effective working length is the usable height you get, roughly half the circumference because the loop is doubled when it hangs.

Tablo 5 — The same sling under both conventions
Site kòm Ki sa li mezire Fistibal la menm egal
Sikonferans The perimeter of the loop — total band in the article 2 m
Longè travay efikas Wotè ki ka itilize; the loop doubles when it hangs 1 m

Non konvansyon an ak figi a, oswa endike itilizasyon an olye de sa - sikonstans atik la bouk la dwe fè wonn - ak anbigwite a disparèt anvan gwoup la koupe.

Green single ply endless sling with its blue capacity label
Etikèt koud la pote limit chaj travay la, materyèl la, estanda a, the length and the batch — on a closed loop it is the whole record of the article.

Polyester, and the limits of it

The standard build is 100% Polyester segondè-tenasite (PES). It elongates no more than 3% at the working load limit and no more than 10% nan chaj la kraze, so the load does not creep down as the lift comes on, and the standard build works from −40 °C to +100 °C. Nylon is offered where shock and abrasion dominate; polypropylene where weight and cost matter more than strength; UHMWPE and aramid where strength-to-weight or heat is the deciding factor.

What ends a polyester build is the same list as for any synthetic sling: heat above the range, strong alkalis, sharp edges that cut rather than abrade, and a cut or a glaze anywhere on the circumference. On a closed loop there is no second end to compare, so condition is judged against the surrounding band.

Single ply endless slings lifting bundles of steel pipe at a loading bay
Pipe bundles at a loading bay: the loop is passed round the bundle and both sides come back to the hook, so the band is doubled where the load is heaviest.

Marking and traceability

  • NAN 1492-1 capacity colour in the weave — violet 1 t, vèt 2 t, jòn 3 t, gri 4 t, wouj 5 t, mawon 6 t, ble 8 t, zoranj 10 t.
  • One black transverse stripe per tonne as a second, chèk optik sou gwoup la tèt li.
  • A sewn label with the working load limit, materyèl, estanda, length and traceability code — and above 10 t, the label is the only rating there is.
  • Every sling proof tested in our own laboratory before dispatch, with a test certificate per batch on request; Kòd HS 630790.
Two single ply yellow endless slings showing the flat band and its thin section
The single-layer section is 4 mm: it folds into a pocket, turns round a small diameter and drapes over the load instead of standing off it.

Mande souvan

What does single ply mean, exactly?

One layer of webbing in the band the loop is made from — not two slings, and not two bands side by side. It gives a 4 mm section at the standard ladder widths, the lowest weight per metre in the range, and the most supple loop we build.

Se yon fistibal kontinuèl san pwoblèm?

Non. Li se kontinuèl nan itilize, pa san pwoblèm: the band is lapped over itself and closed with dense parallel stitching, and that lap is a full-strength joint in the load path. What a closed loop removes is the eyes and the end fittings, not the joint. If you need a closed loop with no joint in the load-bearing element at all, sa se la kontinuèl fistibal wonn, where the core is continuous.

How far up the capacity range does single ply go?

The single-ply ladder is published to 12 t nan 7:1 in a 300 mm bann; the range as a whole runs to 30 t, and above the single-ply ladder the duplex build is the answer rather than a wider single band.

Can I use one loop for a vertical lift and a choke?

Wi, and the figure changes with the arrangement: 1.0 vètikal, 0.8 toufe, 2.0 in a basket with the legs near vertical, tonbe nan 1.4 and then 1.0 as the legs open. Size to the hitch the crew will actually rig.

Will a single ply sling mark aluminium or painted steel?

Gwoup la se fib sentetik epi pa gen okenn Fitting manyen chaj la, so it will not scratch or burr the way a chain or a wire rope can. Width is the protection measure — for mirror-finish or anodised work, specify a width above the capacity ladder and the pressure on the surface falls with it.

How should the length be quoted?

Pa sikonferans oswa pa longè travay efikas - de yo diferan pa apeprè yon faktè de. Non konvansyon an, or give the girth of the article the loop must go round, and the figure is confirmed on the order acknowledgement.

Mande yon sitasyon

Five things settle a single ply loop

The load — what it is, its girth at the pick positions, and its surface;

The hitch — vertical, toufe oswa panyen, and the leg angle if it is a basket;

The working load limit in that hitch, ak faktè sekirite sit ou a ap travay;

The length — with its convention, or the girth the loop has to go round;

The marking and packing — own-brand label, carton or pallet specification.

Send the duty and the figure for a quotation →

Ki kote yo ale pwochen

Lift Sling Rigging Company · Lifute Endistriyèl Park, Taizhou City, Pwovens Jiangsu, Lachin · Kòd HS 630790
Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Kite Mesaj Ou

Scroll nan tèt