50mm 5000kg Ratchet Lashing Belt — Ratchet Tie Down Straps

This is the size most buyers end up with: in 50 mm 5000 kg ratchet lashing belt - 2 inch polyester webbing, a forged ratchet buckle and a hook at each end, rated at a lashing capacity of LC 2,500 En and a minimum breaking strength of 5,000 En. Standard tension force is 350 daN at a hand force of 50 En, and the assembly is built and marked to EN 12195-2.

It is the middle of the range and the reason is arithmetic rather than fashion. 25 mm en 35 mm belts are cheap but narrow: they concentrate the load, they run out of strength on anything above a van, and the buckle a narrow band needs is fiddly in gloves. 75 mm en 100 mm belts carry twice as much, and they are also twice as awkward on a load bed, twice as heavy in the hand and twice the price. De 50 mm sits where the strength is enough for a flatbed, a container or a plant trailer, and the band is still easy to throw over a load and pull through.

What “50mm 5000kg” Actually Means

Three different numbers get sold as “5000kg”, and only one of them describes what the strap may do in service. The sequence below is the one that matters at the counter.

If you are comparing quotations for 50 mm ratchet tie down riemen, ask for the breaking strength in daN and the LC separately, and ask which one the price was quoted against. Two suppliers quoting “5 tonne” can mean the breaking strength and the working figure, and the difference is a factor of two.

Under EN 12195-2 the webbing of a lashing strap must reach at least twice its lashing capacity, which is where the 2:1 relationship comes from: 2,500 daN of rated restraint, 5,000 daN before anything breaks. A North American catalogue will often print the same article as “10,000 lb” because it quotes breaking strength in pounds. Deselde riem, different unit — and a genuine trap when two quotations are compared side by side.

Technical Parameters of the 50mm 5000kg Belt

De tafel is de standert build. Lingte, end fitting, colour and marking are fixed on the order, because the rating applies to the finished assembly — band, stitching and hardware together — not to the roll of webbing it came from.

De 50 mm advantage is not only strength. IN 50 mm band spreads the same preload over twice the area of a 35 mm band, so it crushes a carton, a painted panel or a soft bag far less at the same tension. That is why buyers move up a size for the load’s sake rather than the rating’s.

Attachment Parameters — Buckle, Hooks and End Fittings

The band is the cheap half of the assembly and the fittings are what the buyer is really choosing, because they decide whether the strap fits the vehicle in front of them. Every item below is supplied on a 50 mm belt to your length, or on its own as a spare.

Ratchet buckle

The short-lever ratchet is the standard 50 mm buckle: one gloved hand, a pawl that holds what has been gained, and a drum that winds a few centimetres per stroke. The long aluminium lever trades speed for tension — it reaches the 350 daN STF in fewer strokes and it is the version specified where the operator is working in gloves, at height or in the wet. The buckle is a lever and a winch at once, and the number it produces is the STF on the label, not the LC. Grit in the pawl, a bent lever and a drum that no longer turns freely are the three ways it ends its life early.

Hooks, and why the anchor decides

Specify the anchor point rather than the hook. A double-J with a closed throat for a lashing point or a container fitting; in platte heak foar de râne fan in load bed, because it sits flat and marks the deck least; a vinyl-sleeved S-hook for a ring on light duty. A hook sitting half in its point is the commonest reason a lashing comes loose, and it lets go under braking — which is the moment the strap was bought for. Ringen, shackles and the hardware that takes a belt end are on the lifting apparaten side.

Endless and ring ends

With no hook at all, the belt is passed around the load and tensioned against itself — the configuration a bundle or a pallet needs, and the one that lets a single strap serve several load shapes. A ring end does the same job but leaves a hard point for a shackle or a second belt. Both keep the assembly’s rating, because the band and the stitching are unchanged; only the hardware is missing.

Five Ways the Assembly Is Configured

What Makes a Genuine 5,000 kg Belt — the Weakest Link

Every part of a lashing is rated, and the assembly is rated at the lowest of them. A supplier who quotes 5,000 kg from the webbing alone has quoted a number that does not exist in the box.

De band

50 mm high-tenacity polyester reaches roughly 5,000 daN at 1.8 mm thickness when the weave is dense and the yarn is specified by minimum tenacity. Cheaper band is thinner, lighter and reaches the same width with less strength — it also elongates further, which lets the load walk and then shocks the system when it catches. Ask for the band mass per metre: 88 g/m is this build, and a figure much below it is a different belt.

The stitching

The stitch is a load path, not a seam. IN 50 mm belt carries a box-X pattern in high-tenacity polyester thread at every hook and buckle, with the run stitched in the same thread at a set pitch. Brutsen, worn or pulled stitching at the ends is a retirement condition, not a repair — a restitched belt has no rating unless the maker re-tests it.

De heak

The hook’s minimum breaking strength has to be at or above the assembly’s, dêrom a 50 mm J-hook is forged rather than stamped. A stamped hook on a 5,000 daN band is the single most common way a cheap belt fails: the band survives, the hook opens.

The ratchet

It frame, the pawl and the drum all see the full tension. Zinc-plated forged steel is the material for this rating; the aluminium in a long-lever buckle is the handle, not the frame. A ratchet that lets go under vibration gives no warning from outside the drum, which is why a worn pawl spring is a retirement condition.

How to Check a 5,000 kg Strap on Arrival

• Lês it label, not the listing. LC 2,500 daN and STF 350 daN must be printed on a sewn label with the length, breedte, maker and batch. A sticker is not a label.
• Weigh one strap. IN 6 m 50 mm assembly of this build is about 1.2 kg. A strap that is half the weight is a thinner band with the same colour.
• Measure the band. 50 mm ± 2 % wiid, 1.8 mm thick at the edge, and the weave should be dense enough that you cannot see daylight through it.
• Look at the hook. Forged hooks have a parting line and a solid throat; stamped hooks are folded sheet and open under load.
• Ask for the pull-test record. It is the one document that ties the figure on the label to the batch in the carton.

One more check that costs nothing: pull the strap through your hands and look for a splice, a heat-sealed join or a colour change mid-length. Band is woven in a continuous run and should never be joined.

Using a 5T Belt: Lade, Angle and Friction

IN 2,500 daN belt does not restrain 2.5 tonnes of cargo by itself, and the arithmetic is worth doing once so the number of straps stops being a habit. A load is held against acceleration in three directions and the forward case is normally the worst: most road markets size a lashing at around 0.8 g.

Worked on a 5,000 kg load on a steel deck with a friction coefficient of about 0.3, lashed top-over at 60 degrees to the deck, the standard relation gives:

• Forward force to be held: 5,000 × 0.8 × 9.81 ≈ 39,240 N, or about 3,924 En.
• Friction already helping: 0.3 × 5,000 × 9.81 ≈ 14,715 N, oer 1,472 En.
• Residual to be carried by the lashings: oer 2,452 En of tension at the deck.

Each 50 mm belt contributes a vertical clamping component of 2 × STF × sin 60°, rûchwei 606 daN per belt, and that clamping force turns into friction at the deck. Five belts is the practical answer at 60 degrees — four on a timbered deck, six or more on wet aluminium, which is exactly why the count is a calculation and not a rule of thumb. Anti-slip mats under the load buy more restraint than another half-turn on the handle.

Lengths, Sets and Packing

On a ratchet tie down strap the packing is half the specification and most of the buying decision. A two-piece set with a printed header card is the retail norm for trailer work; a four-piece set is the DIY pack; distributeurs nimme 10 of 20 riemen oan in karton, banded, with the LC and the length on the outside. The sewn label is the part that cannot be changed after the fact: dyn merk, dyn diel nûmer, LC 2,500 daN and STF 350 daN in the unit your market reads, en de batch as jo systeem it nedich is.

For the container and flatbed trade the same belt is often bought as a 6 m single with a short lever and a J-hook, because that is the length that reaches from a deck ring over a pallet and back. If you are buying a mixed order, this is the size to standardise on: ien lingte, ien hok, ien label, en de 25 mm en 75 mm become the exceptions rather than the rule.

Soarch en Pensjonearring

• Cuts and nicks at an edge. De band mislearret fan in skansearre râne nei binnen; a nick reaching the warp is the end of the strap.
• Glazed or stiff fibre. Heat or chemical contact changes the yarn before it looks worn.
• Broken or worn stitching at a hook or buckle.
• A bent or opened hook — once an S-hook has opened it will open again under a smaller load.
• In fersliten ratchet — a pawl that no longer snaps, a weak spring, a drum that drags.
• In ûnlêsber label. Without the LC the belt cannot be matched to a load.

Winkel oprûn, skjin en droech, út 'e flier en út sinneljocht; waskje mei wetter en myld detergent, nea oplosmiddel. IN 50 mm belt left on an open trailer for a season is not the belt that was delivered — polyester takes UV better than polypropylene, but it still fades, stiifet en ferliest krêft foardat it droegen liket.

Faak stelde fragen

Related Products

• Ratchet tie-down riemen - it folsleine berik, 25-100 mm, if 50 mm is not the size you need.
• Cargo lashing — how the number of straps for a consignment is worked out.
• Recycled-fiber car lashing belts — the same size in rPET webbing, for vehicle transport.
• Webbing slingers — the lifting article, with WLL and mode factors.
• 3 tonne platte singels sling — the most-bought lifting size.
• Lifting apparaten — hooks, shackles and rings at the belt end.
• Cargo lift net — when the load is loose rather than packed.
• Rûne slingers — soft lifting slings for machinery and shells.

Lêst bywurke: 6 November 2026 | Standard reference: YN 12195-2 (load restraint assemblies on road vehicles — web lashing). Figures are the standard build for this range; the sewn label on the assembly you receive governs.