Catégories de produits

Robuste 20 Ton Polyester Cargo Lifting Net

Brève description:

Lift sling rigging company produce Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

20 t polyester cargo lifting net: 7:1 facteur de sécurité, 100 mm duplex bands, four or eight points, cut to the load footprint and proof tested per net.

Détail du produit

Lift sling rigging company produce Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

Cargo lifting net · polyester · 20 classe

Robuste 20 Ton Polyester Cargo Lifting Net

UN 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

20 t limite de charge de travail 140 t minimum breaking load 100 mm duplex band 8 points de levage
Heavy duty polyester flat webbing cargo lifting net laid out, wide bands in a square mesh

A heavy duty 20 ton polyester cargo lifting net is a flat lattice of wide high-tenacity polyester bands, stitched into a square mesh with a doubled border and four or eight reinforced lifting points. The load sits inside the mesh and is carried across the full width of every band beneath it, so the pressure on the cargo is spread over a face rather than concentrated on four sling legs.

We build these nets to order in Taizhou: band width and layer, engrener, taille nette, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.

The number behind “20 ton”. The working load limit is 20 t and the safety factor is 7:1, so the net’s minimum breaking load is 140 t. That figure is what the test bed proves; le 20 t is what you are allowed to lift, in the arrangement the net was rated in.

Why polyester at this rating

À 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.

Tableau 1 — Polyester against nylon for a 20 t net
Polyester (ANIMAL DE COMPAGNIE) Nylon (Pennsylvanie)
Stretch under a steady load Low — the net stays square and the load stays level Markedly higher; the net settles and the load can tilt
Absorption des chocs Modéré Best in the family; 18–22 % allongement à la rupture
Absorption d'eau Très faible, dries quickly À propos 4 %, with some strength loss when saturated
Repetitive crane cycles The usual choice Better where pickups are rough
Température de travail −40 °C à +100 °C Lower at the top end
Best fit for a 20 charger Bagged, palletised, bundled or stacked cargo lifted on a cycle Irregular or shocky loads that must settle into the mesh
Nylon rope cargo net for comparison with a flat webbing net
The rope alternative: better on irregular loads, but it stretches far more than a polyester band net under a steady 20 t.

What changes when the rating goes to 20 t

Capacity is not a property of the net’s size. It comes from four things moving together: le groupe, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.

Tableau 2 — Build steps from a light net to a 20 t net
Load band Band and build Engrener Points de levage What else changes
2 – 5 t 50 mm single layer 100 mm 4 corners Standard warehouse net
5 – 10 t 50 – 75 mm, duplex on the load run 100 mm 4 corners, 8 sur demande Heavier border, reinforced loops
10 – 20 t 75 – 100 mm recto-verso 100 – 150 mm 8 points Master ring or spreader beam; net built to drawing
20 – 30 t 100 mm recto-verso, band count from the load face 150 mm 8 points Spreader beam in the assembly; proof test per net
Au-dessus de 30 t 100 mm multi-layer or wider pitch 150 – 200 mm 8 points or more Engineered and tested to the lift, not to a catalogue

Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.

Deux conséquences s’ensuivent. D'abord, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 t sur un 10 t ring is a 10 assemblage. Deuxième, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Corner detail of a heavy duty webbing cargo net, folded double-stitched border and reinforced loop
Détail du coin: the doubled border is spliced into the loop, which is where the whole 20 t passes through — and where a net is inspected first.

Sizing the net to a 20 charger

A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.

  • Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. UN 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
  • Forme de sac: the flat width has to wrap up the sides and close over the top, donc largeur à plat = empreinte + 2 × bag depth. UN 1.2 m footprint in a 0.6 m deep bag needs about 2.4 m à travers.
  • Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.
Flat polyester cargo lifting net spread on the floor with four corner lifting loops
Flat form: the net overhangs the load footprint and the four corners gather on the hook, so the cargo sits inside the lattice rather than on top of it.

Engrener: sized from the cargo, pas le tonnage

Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.

Tableau 3 — Mesh against the smallest piece in the load
Plus petite dimension de chargement Typical cargo at 20 t Maillage à préciser
Sous 75 mm Petits moulages, composants en vrac, drummed goods 100 mm diamant, ou un filet à sac fermé
75 – 150 mm Briques, marchandises en sac, pierre fendue 100 – 150 mm
150 – 250 mm Sawn packs, bundled tube, cartons, ferraille 150 – 200 mm
Sur 250 mm Blocs, grosse pierre, débris de démolition 200 – 300 mm

Spécification

Tableau 4 — Heavy duty 20 ton polyester cargo lifting net
Paramètre Spécification
Taper Open flat webbing lattice, quatre ou huit points de levage
Matériau du bracelet 100 % polyester haute ténacité (ANIMAL DE COMPAGNIE); nylon or UHMWPE on request
Largeur de bande 75 – 100 mm for this class
Band build Duplex (double couche) on the load-bearing run, single layer elsewhere
Ouverture en maille 100 – 150 mm; square standard, diamond on request
Taille nette Typiquement 4.0 × 4.0 m à 6.0 × 6.0 m, or to the load footprint
Limite de charge de travail 20,000 kg in the rated arrangement
Facteur de sécurité 7:1 — charge de rupture minimale 140,000 kilos
Bordure et coins Doubled border, épissé dans les coins; reinforced loops, four or eight
Raccords Master ring or grade 80 chaînes; spreader beam for eight-point lifts
Traitement Stabilisé aux UV, anti-âge, abrasion-resistant finish
Température de travail −40 °C à +100 °C
Marquage WLL, arrangement, net size and identification on a sewn label; band printing on request
Documentation Capacity label, rapport d'essai de matériaux, Marquage CE; tested on our own 1000 t bed
Code HS 630790
Polyester webbing cargo net with the border and lifting loops visible across its width
Border and loops: the perimeter takes the load from corner to corner, so no single stitch line carries the lift.

Eight points, not four, once the load is long

Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.

  • Four points suit square, compact loads where the net is only holding the cargo together;
  • Eight points suit long or wide loads, and any lift where the net must stay flat under load;
  • The spreader or master link, the slings above it and the hook must each be rated at least 20 t;
  • Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.

The leg sees more than the share: à 45 deg from the vertical, un 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.

Inspection et mise à la retraite

Tableau 5 — What ends a net’s service life
Vérifier Retirer ou réparer si
Corner loops and their stitching A loop is deformed, the stitching is broken, or the band is cut at the throat
Frontière La frontière est coupée, flattened, or has pulled out of a corner
Load-bearing bands Any band is cut, profondément abrasé, heat glazed or chemically stained
Mesh geometry The lattice is distorted from an overload — the net no longer sits square
Piqûre Stitch lines are broken or pulled at a crossover
Label and printing The WLL or the arrangement is illegible — an unlabelled net cannot be rated

Inspect before each lift and have the net examined by a competent person at the interval your site sets. Rangez-le propre et sec, hors du sol et à l'abri du soleil direct; never knot, weld or heat-repair a webbing net.

Steel coils loaded inside a webbing cargo net on a factory floor
Coils inside the mesh: at this rating the net is as much a handling tool as a container, and the crane never touches the cargo.

How it is built, and how the rating is proven

  • Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
  • Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
  • Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
  • Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.

La même entreprise tisse des sangles et presse des embouts de câbles métalliques., which is why a net, un élingue en sangle et un élingue en câble métallique on the same lift can be matched in rating rather than bought from three suppliers.

Où un 20 t net does the work

Tableau 6 — Sectors that buy this class
Secteur Ce que le net soulève Construction habituelle
Acier et fabrication Forfaits, rubriques, charges de repos Filet plat, 100 mm recto-verso, eight points
Stone and quarry Blocs, pierre fendue, pavés Forme de sac, 150 maille mm, pièces de coin
Ports et terminaux Bagged and unitised cargo, quay work Flat net on a spreader, WLL imprimée
Bois Sawn packs, poteaux, sleepers Flat or bag, 150 – 200 maille mm
Déchets et recyclage Ferrailles mixtes et abrasives Grande maille, wear bands at the corners
Béton préfabriqué Units, anneaux, panneaux Flat net with edge sleeves, eight points

Foire aux questions

Est-ce que le 20 t rating for the net or for the whole assembly?

The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, chaînes, spreader and slings above must be rated at least 20 t as well.

Why is the safety factor 7:1 and not 5:1?

7:1 is the factor we build to for this class, which gives a 140 t charge de rupture minimale pour un 20 note. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.

Polyester or nylon for a 20 soulever?

Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.

How big a net do I need for a 2 × 2 m load?

At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.

Can it be lifted by a single hook?

Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.

Can you print our brand and the WLL on the net?

Yes — WLL, arrangement, taille nette, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.

Demander un devis

Send the load and how it is presented

The cargo — what it is, comment il est emballé, and the weight as presented for the lift;

The footprint — length × width, plus height if a bag form is needed;

The lift — four or eight points, hauteur du crochet, and whether a spreader beam is available;

The duty — how many lifts a week, indoors or on a quay, and the temperature range;

The paperwork — CE marking, test report and own-brand printing if you need them.

Send the load and the footprint for a quotation →

Où aller ensuite

Entreprise de gréage d'élingues de levage · Lifute Industrial Park, Ville de Taizhou, Province du Jiangsu, Chine · Code SH 630790
Tél +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Laissez votre message

Faire défiler vers le haut