Mga Kategorya ng Produkto

5 Ton Heavy Duty Ratchet Straps

Maikling Paglalarawan:

Lift sling rigging company produce 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

5 ton heavy duty ratchet straps: 50 mm polyester, 5,000 at masira, LC 2,500 daN sa EN 12195-2. hindi kinakalawang 304/316 and aramid high-temp builds. Direkta sa pabrika.

Detalye ng Produkto

Lift sling rigging company produce 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

Cargo restraint · EN 12195-2

5 Ton Heavy Duty Ratchet Straps

50 mm polyester webbing, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

2,500 At kapasidad ng paghampas 5,000 At pagkasira ng lakas 350 At STF sa 50 daN hand 3–10 m standard length
5 ton heavy duty ratchet straps with hook options: claw hook, flat hook, D ring and S hook

“5 ton heavy duty ratchet straps” is the phrase buyers search for, and the reason this page exists is that the phrase covers two different articles. Sa isang 50 mm polyester assembly the breaking strength is 5,000 At at ang kapasidad ng paghampas (LC) ay 2,500 At. Both numbers are real, both are printed on the same label, and quoting one against the other is how trailers get overloaded. We build the assembly to EN 12195-2, mark it, and state both figures so the comparison you make at quotation stage is between like and like.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 sa 10 m bilang pamantayan, LC 2,500 At, STF 350 at N sa 50 at lakas ng kamay. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.

Part of the webbing lambanog and lashing range. Ang 50 mm specification in isolation sits on the 50 mm 5000 kg ratchet lashing belt pahina.

What “5 Ton” Actually Means on a Ratchet Strap

Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. Sa ilalim ng EN 12195-2 ang webbing ng isang lashing strap ay dapat umabot ng hindi bababa sa dalawang beses sa kapasidad nito sa paghagupit, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.

mesa 1 — The three numbers on a 5 ton heavy duty ratchet strap
Pigura Value on the 50 mm assembly Ang inilalarawan nito How it gets misread
Pinakamababang lakas ng breaking 5,000 At (5,000 kg) Ang pagkarga kung saan nabigo ang pagpupulong sa isang pagsubok sa paghila Read as the working figure — the mistake that overloads a trailer
Lashing kapasidad (LC) 2,500 At (2.5 t) Ang pagpigil sa pagpupulong ay na-rate na hawakan, printed on the label Kumpara sa WLL ng nakakataas na lambanog, which is a different duty altogether
Karaniwang puwersa ng pag-igting (STF) 350 at N sa 50 at lakas ng kamay The tension one person reaches with the ratchet handle Nalilito kay LC, kaya ang operator ay patuloy na paikot-ikot na lampas sa kapaki-pakinabang na punto
Ask for both numbers. Two suppliers quoting “5 tonne” can be quoting the breaking strength and the working figure — a factor of two apart — and a North American catalogue printing the same article as “10,000 lb” is quoting breaking strength in pounds. Parehong sinturon, different unit, same trap.

Bakit ang 50 mm Build Is the Heavy-Duty Default

Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. Ang 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.

mesa 2 — Width ladder: where 50 mm sits
Lapad ng web Typical LC Nakakasira ng lakas Para saan ito binili
25 mm (1 sa) 400–500 daN 800–1,000 daN Tool boxes, light restraint, tight anchor eyes
35 mm (1-3/8 sa) 750 At 1,500 At Van and trailer decks, general cargo
38 mm (1-1/2 sa) 1,000–1,500 daN 2,000–3,000 daN Platong bakal, mga bundle ng tubo, plant
50 mm (2 sa) 2,500 At 5,000 At Heavy cargo restraint, mga coils, makinarya, mga lalagyan
75–100 mm 5,000 daN and up 10,000 daN and up Abnormal loads, where the bed allows the width

The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.

Standard Specification of the 5 Ton Assembly

mesa 3 — 50 mm 5 ton heavy duty ratchet strap: teknikal na mga parameter
item Pagtutukoy
Webbing 100% high-tenacity polyester, twill weave, Nag-stabilize ang UV, 50 mm ± 2%
Kapal ng banda / misa 1.8 mm nominal / 88 g per metre
Lashing kapasidad (LC) 2,500 at bawat kapulungan
Pinakamababang lakas ng breaking 5,000 At (2:1 against LC)
Karaniwang puwersa ng pag-igting (STF) 350 at N sa 50 at lakas ng kamay
Tensioner Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle
Pagpahaba sa LC 7% o mas kaunti
Temperatura ng serbisyo −40 °C hanggang +100 °C (polyester webbing)
Karaniwang haba 3–10 m; 1–30 m to order
Pagmamarka Habi label: LC, STF, haba, batch number, standard reference
Pamantayan Designed, tested and marked to EN 12195-2
HS code 630790

The End Fitting Decides Whether the Strap Fits the Job

The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.

mesa 4 — End fittings for 5 ton heavy duty ratchet straps
Angkop Anchors to Notes before ordering
Chassis rave hook Flatbed side rail, chassis lip Check rail thickness and that the hook throat clears it
Claw hook Anchor rings, D rings, recessed eyes Opening must clear the ring; load on the crown only
D ring / delta ring Welded or bolted anchor points Ring bore at least as wide as the webbing
Flat snap hook E-track, slotted rail, mga butas Confirm slot width; snap gate must close fully
S hook Mga tubo, riles, frame members Both ends must seat without point loading on a weld
Sewn loop / looped ends Around the load or through a bore Nothing metal at the load; ideal for finished surfaces
Walang katapusang, walang angkop Girth only — hulls, mga coils, mga bundle See the endless loop build below
5 ton heavy duty ratchet straps with hook options: claw hook, flat hook, D ring and S hook
Isa 50 mm banda, eight ways to terminate it — the hook option decides which anchor the strap can reach.

Ang 5 Ton Strap in Two Special Builds

Polyester covers most freight, and it fails predictably when it is out of its depth: lumalambot ito sa paligid 150 °C and melts at about 255 °C, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.

Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces

The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 o 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 at N sa 25 mm sa 2,500 at N sa 50 mm, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.

The grade decision is about chloride, not load. 304 (1.4301) handles rain, fresh water, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 in the belief that it is stronger is paying for the wrong property. Kung saan ang aplikasyon ay nauugnay sa kaligtasan, kumpirmahin ang grado sa sertipiko ng gilingan sa halip na sa paglalarawan ng invoice.

Two shop-floor notes worth passing on. Hindi kinakalawang na sinulid apdo, so a dry 316 nut tumakbo nang husto papunta sa a 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. At ang hindi kinakalawang na bolted sa aluminyo sa tubig-alat ay bumubuo ng isang galvanic na pares, so where the strap anchors to an alloy frame, ihiwalay ang kontak.

Full range and grade comparison: walang katapusang hindi kinakalawang na asero ratchet strap.

Aramid (Kevlar) ratchet straps — for heat, sparks and cut edges

Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 °C. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.

The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.

Two honest limits. Aramid is flame retardant, not fireproof: molten steel, ladles and hot slag still need a heat shield or a stand-off. And low elongation is exactly wrong for snatch and shock loads — for those, the polyester band or a dedicated recovery strap is the right article.

Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.

How Many Straps Does the Load Actually Need?

Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.

mesa 5 — Worked example: 50 mm straps at 2,500 daN LC
Straps used Angle to the deck Restraint per strap Total restraint
2 45° tinatayang. 1,750 At tinatayang. 3,500 At
4 30° tinatayang. 1,250 At tinatayang. 5,000 At
4 45° tinatayang. 1,750 At tinatayang. 7,000 At
4 60° tinatayang. 2,165 At tinatayang. 8,660 At
6 45° tinatayang. 1,750 At tinatayang. 10,500 At

The arithmetic is an illustration, not a lashing plan: SA 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.

Kung saan ang 5 Ton Ratchet Strap Earns Its Keep

  • Flatbed, container and plant trailer restraint — the volume application for the 50 mm build.
  • Steel coil, slab, billet and pipe bundles, with edge protection at the contact points.
  • Makinarya, moulds and skid-mounted plant, saan a 25 mm strap has neither the width nor the tension.
  • Mga pakete ng kahoy, crates and stillages, including the endless form that simply closes round the pack.
  • Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
  • Marine, marina and wash-down duty in 304 o 316 where plated hardware would be a maintenance item.
  • Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.
5 ton heavy duty ratchet straps securing a timber crate on a flatbed truck
50 mm straps over a timber crate on a flatbed — two legs at roughly 45°, hooks seated on the crown of the rail.

Kulay, Printing and Private Label

Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, kulay kahel, dilaw, itim, pula, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, haba, standard and traceability code. Cartons of 10 sa 20 mga piraso, palletised for export, with neutral or own-brand packaging as required.

Pagsubok, Traceability and the Paperwork Buyers Ask For

Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. Mga ulat sa pagsubok, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.

One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.

Mga Madalas Itanong

Ay a 5 ton ratchet strap rated to lift 5 tonelada?

Hindi, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.

Why does the same strap get called 5 tonelada at 2.5 tonelada?

Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.

50 mm o 38 mm for a flatbed?

50 mm, unless the anchor points are small. Ang 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; ang 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.

Do I need 304 o 316 hindi kinakalawang?

316 where chloride is present — sea air, spray ng asin, de-icing salt, boatyards, halaman ng pagkain. 304 is enough for rain, fresh water, condensation and indoor wash-down. The difference is corrosion resistance, hindi lakas.

At what temperature does polyester fail, and what does aramid do instead?

Polyester softens around 150 °C and melts at about 255 °C, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 °C, and chars at about 427 °C sa halip na matunaw. sa itaas 400 °C, or against molten metal, both need a heat shield.

Can the strap be supplied with a printed brand and a custom length?

Oo. Mga lapad, haba sa 30 m, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.

Humiling ng Sipi

Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, ang kapaligiran (salt, init, hugasan-down), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.

Kumpanya ng Lift Sling Rigging

Lifute Industrial Park, Lungsod ng Taizhou, Lalawigan ng Jiangsu, Tsina

Tel: +86 523 8693 5818 · WhatsApp: +86 180 6600 2268

E-mail: 702461526@qq.com · HS code 630790

Send your lifting details for a quotation →

Mga Kaugnay na Produkto

Kumpanya ng Lift Sling Rigging · Lifute Industrial Park, Lungsod ng Taizhou, Lalawigan ng Jiangsu, China · HS code 630790
Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com · xulft.com

 

Iwanan ang Iyong Mensahe

Mag-scroll sa Itaas