تولید شرکت دکل زنی بالابر 5 Ton Heavy Duty Ratchet Straps,10 Tonne Ratchet Strap,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.
5 Ton Heavy Duty Ratchet Straps
50 میلی متر بافته پلی استر, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 به 10 m به عنوان استاندارد, LC 2,500 و, STF 350 daN at 50 و نیروی دست. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.
Part of the زنجیر بافته شده and lashing range. را 50 mm specification in isolation sits on the 50 میلی متر 5000 تسمه ضامن دار کیلوگرمی صفحه.
What “5 Ton” Actually Means on a Ratchet Strap
Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. تحت EN 12195-2 the webbing of a lashing strap must reach at least twice its lashing capacity, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.
| شکل | Value on the 50 mm assembly | آنچه را توصیف می کند | How it gets misread |
|---|---|---|---|
| حداقل قدرت شکست | 5,000 و (5,000 کیلوگرم) | باری که در آن مجموعه در تست کشش شکست می خورد | Read as the working figure — the mistake that overloads a trailer |
| ظرفیت شلاق (LC) | 2,500 و (2.5 تی) | The restraint the assembly is rated to hold, printed on the label | در مقایسه با WLL یک زنجیر بالابر, which is a different duty altogether |
| نیروی کشش استاندارد (STF) | 350 daN at 50 و نیروی دست | The tension one person reaches with the ratchet handle | با ال سی اشتباه گرفته شده, بنابراین اپراتور از نقطه مفید عبور می کند |
چرا 50 mm Build Is the Heavy-Duty Default
Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. را 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.
| عرض وب | Typical LC | قدرت شکستن | What it is bought for |
|---|---|---|---|
| 25 میلی متر (1 در) | 400–500 daN | 800–1,000 daN | Tool boxes, light restraint, tight anchor eyes |
| 35 میلی متر (1-3/8 در) | 750 و | 1,500 و | Van and trailer decks, general cargo |
| 38 میلی متر (1-1/2 در) | 1,000–1,500 daN | 2,000–3,000 daN | ورق فولادی, بسته های لوله, plant |
| 50 میلی متر (2 در) | 2,500 و | 5,000 و | Heavy cargo restraint, کویل ها, ماشین آلات, ظروف |
| 75-100 میلی متر | 5,000 daN and up | 10,000 daN and up | Abnormal loads, where the bed allows the width |
The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.
Standard Specification of the 5 Ton Assembly
| مورد | مشخصات |
|---|---|
| تاربندی | 100% پلی استر با مقاومت بالا, بافت جناغی, UV تثبیت شد, 50 mm ± 2% |
| ضخامت باند / جرم | 1.8 mm nominal / 88 g per metre |
| ظرفیت شلاق (LC) | 2,500 و در هر مجموعه |
| حداقل قدرت شکست | 5,000 و (2:1 against LC) |
| نیروی کشش استاندارد (STF) | 350 daN at 50 و نیروی دست |
| کشنده | Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle |
| ازدیاد طول در LC | 7% یا کمتر |
| دمای سرویس | -40 درجه سانتیگراد تا +100 درجه سانتی گراد (بافته پلی استر) |
| طول استاندارد | 3-10 متر; 1–30 m to order |
| علامت گذاری | برچسب بافته شده: LC, STF, طول, شماره دسته, standard reference |
| استاندارد | Designed, tested and marked to EN 12195-2 |
| کد HS | 630790 |
The End Fitting Decides Whether the Strap Fits the Job
The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.
| مناسب | Anchors to | Notes before ordering |
|---|---|---|
| Chassis rave hook | Flatbed side rail, chassis lip | Check rail thickness and that the hook throat clears it |
| Claw hook | Anchor rings, D rings, recessed eyes | Opening must clear the ring; load on the crown only |
| D ring / حلقه دلتا | Welded or bolted anchor points | Ring bore at least as wide as the webbing |
| Flat snap hook | تراک الکترونیکی, slotted rail, سوراخ ها | Confirm slot width; snap gate must close fully |
| S hook | لوله ها, rails, frame members | Both ends must seat without point loading on a weld |
| Sewn loop / looped ends | Around the load or through a bore | Nothing metal at the load; ideal for finished surfaces |
| بی پایان, مناسب نیست | Girth only — hulls, کویل ها, بسته نرم افزاری | See the endless loop build below |

را 5 Ton Strap in Two Special Builds
Polyester covers most freight, and it fails predictably when it is out of its depth: اطرافش نرم میشه 150 °C and melts at about 255 درجه سانتی گراد, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.
Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces
The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 یا 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 daN at 25 میلی متر به 2,500 daN at 50 میلی متر, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.
The grade decision is about chloride, بار نمی شود. 304 (1.4301) handles rain, آب شیرین, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 با این باور که قوی تر است، پرداخت برای اموال اشتباه است. جایی که برنامه مربوط به ایمنی است, درجه را در گواهی کارخانه به جای شرح فاکتور تأیید کنید.
Two shop-floor notes worth passing on. رزوه های ضد زنگ, so a dry 316 مهره به سختی روی a اجرا شود 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. و پیچ های ضد زنگ به آلومینیوم در آب نمک یک جفت گالوانیکی را تشکیل می دهد, so where the strap anchors to an alloy frame, مخاطب را جدا کنید.
Full range and grade comparison: بند ضامن دار فولادی ضد زنگ بی پایان.
آرامید (کولار) ratchet straps — for heat, sparks and cut edges
Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 درجه سانتی گراد. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.
The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.
Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.
How Many Straps Does the Load Actually Need?
Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.
| Straps used | Angle to the deck | Restraint per strap | Total restraint |
|---|---|---|---|
| 2 | 45درجه | تقریبا. 1,750 و | تقریبا. 3,500 و |
| 4 | 30درجه | تقریبا. 1,250 و | تقریبا. 5,000 و |
| 4 | 45درجه | تقریبا. 1,750 و | تقریبا. 7,000 و |
| 4 | 60درجه | تقریبا. 2,165 و | تقریبا. 8,660 و |
| 6 | 45درجه | تقریبا. 1,750 و | تقریبا. 10,500 و |
The arithmetic is an illustration, not a lashing plan: در 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.
جایی که 5 Ton Ratchet Strap Earns Its Keep
- Flatbed, container and plant trailer restraint — the volume application for the 50 mm build.
- Steel coil, دال, billet and pipe bundles, with edge protection at the contact points.
- ماشین آلات, moulds and skid-mounted plant, جایی که a 25 mm strap has neither the width nor the tension.
- بسته های چوبی, crates and stillages, including the endless form that simply closes round the pack.
- Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
- دریایی, marina and wash-down duty in 304 یا 316 where plated hardware would be a maintenance item.
- Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.

رنگ, Printing and Private Label
Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, نارنجی, زرد, سیاه, قرمز, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, طول, standard and traceability code. Cartons of 10 به 20 قطعات, palletised for export, with neutral or own-brand packaging as required.
تست کردن, Traceability and the Paperwork Buyers Ask For
Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. Test reports, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.
One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.
سوالات متداول
یک است 5 ton ratchet strap rated to lift 5 تن?
خیر, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.
Why does the same strap get called 5 تن و 2.5 تن?
Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.
50 میلی متر یا 38 mm for a flatbed?
50 میلی متر, unless the anchor points are small. را 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; را 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.
Do I need 304 یا 316 ضد زنگ?
316 where chloride is present — sea air, نمک پاش, نمک یخ زدایی, boatyards, گیاهان غذایی. 304 is enough for rain, آب شیرین, condensation and indoor wash-down. The difference is corrosion resistance, نه قدرت.
At what temperature does polyester fail, and what does aramid do instead?
Polyester softens around 150 °C and melts at about 255 درجه سانتی گراد, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 درجه سانتی گراد, and chars at about 427 °C instead of melting. بالا 400 درجه سانتی گراد, or against molten metal, both need a heat shield.
Can the strap be supplied with a printed brand and a custom length?
بله. عرض ها, طول به 30 متر, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.
درخواست نقل قول
Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, محیط زیست (salt, گرما, شستشو کردن), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.
شرکت لیفت اسلینگ ریگینگ
شهرک صنعتی لیفوت, شهر تایژو, استان جیانگ سو, چین
تلفن: +86 523 8693 5818 · واتس اپ: +86 180 6600 2268
ایمیل: 702461526@qq.com · HS code 630790
محصولات مرتبط
- Ratchet straps — the full lashing range, 25 میلی متر به 100 میلی متر.
- 50 میلی متر 5000 تسمه ضامن دار کیلوگرمی — this specification in detail.
- Endless loop ratchet strap — closed loop, بدون قلاب, for girth-only loads.
- Endless stainless steel ratchet strap - 304 یا 316 for salt and wash-down.
- Aramid flame retardant ratchet straps - 200 درجه سانتی گراد پیوسته, 400 °C peak.
- زنجیر بافته پلی استر — when the job is lifting rather than lashing.

