Categorías de productos

5 Ton Heavy Duty Ratchet Straps

Breve descripción:

Producción de la empresa de aparejos de eslingas de elevación 5 Ton Heavy Duty Ratchet Straps,10 Correa de trinquete de tonelada,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

5 ton heavy duty ratchet straps: 50 mm poliéster, 5,000 y romper, LC 2,500 daN a EN 12195-2. Inoxidable 304/316 and aramid high-temp builds. Directo de fábrica.

Detalle del producto

Producción de la empresa de aparejos de eslingas de elevación 5 Ton Heavy Duty Ratchet Straps,10 Correa de trinquete de tonelada,5-Ton Heavy Duty Ratchet Tie Down Strap,5.000daN Lashing strap,5000kg Truck ratchet strap,5 Tonne Ratchet Strap with Chassis Rave Hook,5000kg Ratchet Strap Claw Hook,5000kg Ratchet Strap D Ring,5000kg Ratchet Strap Flat Snap Hook,Ratchet Strap Looped Ends,Ratchet Strap S Hooks.

Cargo restraint · EN 12195-2

5 Ton Heavy Duty Ratchet Straps

50 correas de poliéster de mm, a forged ratchet and 2,500 daN of lashing capacity — plus a stainless build for salt and an aramid build for heat.

2,500 Y capacidad de amarre 5,000 Y fuerza de rotura 350 Y STF en 50 daN hand 3–10 metros standard length
5 ton heavy duty ratchet straps with hook options: claw hook, gancho plano, D ring and S hook

“5 ton heavy duty ratchet straps” is the phrase buyers search for, and the reason this page exists is that the phrase covers two different articles. en un 50 mm polyester assembly the breaking strength is 5,000 Y y el capacidad de amarre (LC) es 2,500 Y. Both numbers are real, both are printed on the same label, and quoting one against the other is how trailers get overloaded. We build the assembly to EN 12195-2, mark it, and state both figures so the comparison you make at quotation stage is between like and like.

The standard build is 50 mm high-tenacity polyester webbing, a forged ratchet tensioner with a 300 mm handle, and the end fitting your anchor point needs — chassis rave hook, claw hook, D ring, flat snap hook, S hook, sewn loop or no fitting at all. Lengths run 3 a 10 m como estándar, LC 2,500 Y, STF 350 daN at 50 y fuerza de la mano. Two special builds sit alongside it for the jobs polyester cannot take: a stainless ratchet on the same webbing for salt and wash-down duty, and para-aramid webbing for steel that is still hot.

Part of the eslinga de cincha and lashing range. El 50 mm specification in isolation sits on the 50 milímetros 5000 correa de amarre con trinquete kg página.

What “5 Ton” Actually Means on a Ratchet Strap

Three figures appear on a lashing strap and only one of them describes what the strap is allowed to do in service. Bajo EN 12195-2 la cinta de una correa de amarre debe alcanzar al menos el doble de su capacidad de amarre, which is where the familiar 2:1 relationship comes from — and where the confusion starts, because “5,000 kg” is the failure figure, not the working figure.

Mesa 1 — The three numbers on a 5 ton heavy duty ratchet strap
Cifra Value on the 50 mm assembly lo que describe How it gets misread
Resistencia mínima a la rotura 5,000 Y (5,000 kilos) La carga a la que falla el conjunto en una prueba de tracción. Read as the working figure — the mistake that overloads a trailer
Capacidad de amarre (LC) 2,500 Y (2.5 t) La restricción que el conjunto está clasificado para mantener., printed on the label Comparado con la WLL de una eslinga de elevación, which is a different duty altogether
Fuerza de tensión estándar (STF) 350 daN at 50 y fuerza de la mano The tension one person reaches with the ratchet handle Confundido con LC, para que el operador siga pasando el punto útil
Ask for both numbers. Two suppliers quoting “5 tonne” can be quoting the breaking strength and the working figure — a factor of two apart — and a North American catalogue printing the same article as “10,000 lb” is quoting breaking strength in pounds. Mismo cinturón, different unit, same trap.

¿Por qué el 50 mm Build Is the Heavy-Duty Default

Width is a compromise between strength, handling and what the anchor will accept. Narrow bands are cheap but concentrate the load and run out of capacity above a van; the widest belts carry twice as much and are twice as awkward to throw over a load bed. El 50 mm sits where the strength covers a flatbed, a container or a plant trailer while the band can still be handled in gloves.

Mesa 2 — Width ladder: where 50 mm sits
Ancho de banda Typical LC fuerza de ruptura Para que se compra
25 milímetros (1 en) 400–500 daN 800–1,000 daN Tool boxes, light restraint, tight anchor eyes
35 milímetros (1-3/8 en) 750 Y 1,500 Y Van and trailer decks, general cargo
38 milímetros (1-1/2 en) 1,000–1,500 daN 2,000–3,000 daN Placa de acero, haces de tubos, plant
50 milímetros (2 en) 2,500 Y 5,000 Y Heavy cargo restraint, bobinas, maquinaria, contenedores
75–100 milímetros 5,000 daN and up 10,000 daN and up Abnormal loads, where the bed allows the width

The hardware matters as much as the band. The ratchet is forged steel with a case-hardened pawl and gear, and the handle is dimensioned so the standard tension force is reached inside the 250 N manual limit of EN 12195-2 — no extension bars and no cheater pipes, which is how handles get bent and operators get hurt.

Standard Specification of the 5 Ton Assembly

Mesa 3 — 50 milímetros 5 ton heavy duty ratchet strap: parámetros técnicos
Artículo Especificación
Cincha 100% poliéster de alta tenacidad, tejido de sarga, Estabilizado a los rayos UV, 50 milímetros ± 2%
Grosor de la banda / masa 1.8 mmnominales / 88 g per metre
Capacidad de amarre (LC) 2,500 y por montaje
Resistencia mínima a la rotura 5,000 Y (2:1 against LC)
Fuerza de tensión estándar (STF) 350 daN at 50 y fuerza de la mano
tensor Forged steel ratchet, black electrophoretic coating, case-hardened pawl, 300 mm handle
Elongación en LC 7% o menos
Temperatura de servicio −40°C a +100 °C (correas de poliéster)
Longitud estándar 3–10 metros; 1–30 m to order
Calificación etiqueta tejida: LC, STF, longitud, número de lote, standard reference
Estándar Designed, tested and marked to EN 12195-2
código SA 630790

The End Fitting Decides Whether the Strap Fits the Job

The webbing is the easy half. The fitting has to reach the anchor the vehicle actually has, seat on the crown of the eye rather than the point of another hook, and stay seated when the load shifts.

Mesa 4 — End fittings for 5 ton heavy duty ratchet straps
Adecuado Anchors to Notes before ordering
Chassis rave hook Flatbed side rail, chassis lip Check rail thickness and that the hook throat clears it
Claw hook Anchor rings, D rings, recessed eyes Opening must clear the ring; load on the crown only
D ring / delta ring Welded or bolted anchor points Ring bore at least as wide as the webbing
Flat snap hook Pista electrónica, slotted rail, agujeros Confirm slot width; snap gate must close fully
S hook Tubería, rieles, frame members Both ends must seat without point loading on a weld
Sewn loop / looped ends Around the load or through a bore Nothing metal at the load; ideal for finished surfaces
Sin fin, sin ajuste Girth only — hulls, bobinas, paquetes See the endless loop build below
5 ton heavy duty ratchet straps with hook options: claw hook, gancho plano, D ring and S hook
Uno 50 banda de mm, eight ways to terminate it — the hook option decides which anchor the strap can reach.

El 5 Ton Strap in Two Special Builds

Polyester covers most freight, and it fails predictably when it is out of its depth: se suaviza alrededor 150 °C and melts at about 255 °C, and it corrodes nothing but is let down by plated hardware in salt. The two builds below exist for exactly those two failure modes, and they are ordered by customers who have already had the failure once.

Stainless steel ratchet tie downs — for salt, wash-down and finished surfaces

The stainless build keeps the same 50 mm polyester webbing and replaces the hardware with AISI 304 o 316: ratchet frame, rivets, spring and, where an anchor exists, stainless wire hooks. LC runs from 400 daN at 25 mm a 2,500 daN at 50 milímetros, still at 2:1 against webbing break. Most orders are the endless form, where the strap closes on itself through the ratchet and the buckle is the only metal part in the whole assembly — and it sits outside the loop, so a hull, a mast section or a coil sees webbing only.

The grade decision is about chloride, no cargar. 304 (1.4301) handles rain, agua dulce, condensation and indoor wash-down; 316 (1.4401/1.4404) adds molybdenum for salt spray, marina air, de-icing salt and food plants. Both are annealed to a comparable strength, so paying for 316 en la creencia de que es más fuerte es pagar por la propiedad equivocada. Where the application is safety-related, confirm the grade on the mill certificate rather than on the invoice description.

Two shop-floor notes worth passing on. Stainless threads gall, so a dry 316 nut run hard onto a 316 stud can seize — the ratchet is assembled lubricated and should be re-lubricated rather than forced with a bar. And stainless bolted to aluminium in salt water forms a galvanic pair, so where the strap anchors to an alloy frame, isolate the contact.

Full range and grade comparison: correa de trinquete sin fin de acero inoxidable.

aramida (kevlar) ratchet straps — for heat, sparks and cut edges

Para-aramid webbing behaves differently from polyester at temperature. It has no practical melting point: at about 427 °C it chars and carbonises instead of melting and dripping, its limiting oxygen index is 28 or above so it self-extinguishes once the ignition source is removed, and it holds 200 °C continuously with short-term peaks to 400 °C. On a steel coil that is still warm from the mill, a polyester strap of the same width would already have lost its tension; the aramid band is still doing its job.

The second property is mechanical. Para-aramid has roughly three times the tenacity of polyester at equal thickness, with the cut and abrasion resistance that coil edges, slab corners, galvanised strip and scaffolding demand, and a denser weave so damage stays local instead of unravelling across the width. Elongation at break is only 2.4–3.5%, which is what a static restraint wants — the strap does not creep, and it does not need re-tensioning when the load cools.

Two honest limits. Aramid is flame retardant, not fireproof: molten steel, ladles and hot slag still need a heat shield or a stand-off. And low elongation is exactly wrong for snatch and shock loads — for those, the polyester band or a dedicated recovery strap is the right article.

Widths 25–50 mm, LC 500–2,500 daN, standard lengths 1–10 m: aramid flame retardant ratchet straps.

How Many Straps Does the Load Actually Need?

Lashing capacity is not the same thing as restraint delivered. A strap tensioned at an angle gives a horizontal component that is smaller than its LC, and the angle is the operator’s choice, not the supplier’s. At 45° a strap delivers roughly 0.7 of its lashing capacity; bring the legs closer to vertical and the figure rises towards the full LC, lay them flatter and it falls away.

Mesa 5 — Worked example: 50 mm straps at 2,500 daN LC
Straps used Angle to the deck Restraint per strap Total restraint
2 45° aprox. 1,750 Y aprox. 3,500 Y
4 30° aprox. 1,250 Y aprox. 5,000 Y
4 45° aprox. 1,750 Y aprox. 7,000 Y
4 60° aprox. 2,165 Y aprox. 8,660 Y
6 45° aprox. 1,750 Y aprox. 10,500 Y

The arithmetic is an illustration, not a lashing plan: EN 12195-2 also brings friction between load and deck into the calculation, and a low-friction load on a steel bed needs anti-slip matting before extra straps. Send us the cargo weight, the deck, the anchor points and the route, and we will state the number of straps and the angle rather than leave it to the yard.

donde el 5 Ton Ratchet Strap Earns Its Keep

  • Cama plana, container and plant trailer restraint — the volume application for the 50 mm build.
  • bobina de acero, losa, billet and pipe bundles, with edge protection at the contact points.
  • Maquinaria, moulds and skid-mounted plant, donde un 25 mm strap has neither the width nor the tension.
  • Paquetes de madera, cajas y vinazas, including the endless form that simply closes round the pack.
  • Vehicle transport and recovery decks, holding cars and plant to the bed rather than to a hook.
  • Marina, marina and wash-down duty in 304 o 316 where plated hardware would be a maintenance item.
  • Steel mills, foundries and glass plants in aramid, where polyester would melt before the shift ended.
5 ton heavy duty ratchet straps securing a timber crate on a flatbed truck
50 mm straps over a timber crate on a flatbed — two legs at roughly 45°, hooks seated on the crown of the rail.

Color, Printing and Private Label

Band colour is a customer choice rather than a rating, which is why the same 50 mm assembly ships in blue, naranja, amarillo, negro, rojo, olive or a matched shade. Brand, LC and a batch number can be printed directly on the webbing so the strap is identifiable after years in a warehouse, and the sewn label carries LC, STF, longitud, standard and traceability code. Cartons of 10 a 20 pieces, palletised for export, with neutral or own-brand packaging as required.

Pruebas, Traceability and the Paperwork Buyers Ask For

Every production batch is sampled for breaking strength at the 2:1 ratio the standard requires, and each assembly carries a batch number that traces back to the webbing roll and the hardware lot. Informes de prueba, material declarations, mill certificates for stainless grades and lashing capacity calculations are available for tender packages and safety audits.

One point worth being blunt about: any claim of EN 12195-2 conformity, CE marking or a third-party test mark has to match the documents actually held for that product and that factory. We state the standard the assembly is built and tested to, and we send the report with the shipment, because a claim that cannot be produced costs more than the order it wins.

Preguntas frecuentes

es un 5 ton ratchet strap rated to lift 5 montones?

No, and it is not rated to lift at all. A lashing strap carries a lashing capacity — 2,500 daN on the 50 mm build — for restraint in transit. Lifting needs a sling with the correct safety factor and its own marking. A strap bought for restraint and used as a sling is the most common and most serious misuse in this category.

Why does the same strap get called 5 tonelada y 2.5 tonelada?

Because two different figures are being quoted. 5,000 daN is the minimum breaking strength; 2,500 daN is the lashing capacity the assembly is rated to hold, at the 2:1 ratio EN 12195-2 requires. Always ask which figure a quotation is against.

50 milímetros o 38 mm for a flatbed?

50 milímetros, unless the anchor points are small. El 38 mm is a genuine 1,000–1,500 daN strap and suits plate and pipe; el 50 mm gives 2,500 daN with a longer handle and a heavier ratchet, and it is the size most flatbed and container work ends up with.

Do I need 304 o 316 inoxidable?

316 where chloride is present — sea air, spray de sal, sal descongelada, boatyards, plantas alimenticias. 304 is enough for rain, agua dulce, condensation and indoor wash-down. The difference is corrosion resistance, no fuerza.

At what temperature does polyester fail, and what does aramid do instead?

Polyester softens around 150 °C and melts at about 255 °C, and it drips burning polymer as it goes. Para-aramid holds 200 °C continuously, takes short peaks to 400 °C, and chars at about 427 °C instead of melting. Arriba 400 °C, or against molten metal, both need a heat shield.

Can the strap be supplied with a printed brand and a custom length?

Sí. Anchos, longitudes a 30 metro, band colour, webbing print, label layout and packaging are all made to order, and the rating applies to the finished assembly rather than to the roll of webbing.

Solicitar una cotización

Five lines are enough for an accurate price and an accurate rating: the cargo weight and shape, the deck and anchor points, el medio ambiente (salt, calor, lavado), the length and the end fitting. We reply with the assembly, the LC and STF figures, the standard it is built to and the lead time.

Empresa de aparejos de eslingas de elevación

Parque Industrial Lifute, Ciudad de Taizhou, Provincia de Jiangsu, Porcelana

Teléfono: +86 523 8693 5818 · WhatsApp: +86 180 6600 2268

Correo electrónico: 702461526@qq.com · HS code 630790

Send your lifting details for a quotation →

Productos relacionados

Empresa de aparejos de eslingas de elevación · Lifute Industrial Park, Ciudad de Taizhou, Provincia de Jiangsu, China · código SA 630790
Teléfono +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · ascensor98@jslift.com · xulft.com

 

Deja tu mensaje

Desplazarse hacia arriba