Mga Kategorya sa Produkto

Bug-at nga Katungdanan 20 Ton Polyester Cargo Lifting Net

Mubo nga Deskripsyon:

Ang kompanya sa lift sling rigging naghimo og Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

20 t polyester cargo lifting net: 7:1 hinungdan sa kaluwasan, 100 mm duplex bands, four or eight points, cut to the load footprint and proof tested per net.

Detalye sa Produkto

Ang kompanya sa lift sling rigging naghimo og Heavy Duty 20 Ton Polyester Cargo Lifting Net,10Ton Cargo Lifting Net,30T Cargo Net,50Tonne Lifting Net,20Tonne Cargo Net,

Cargo lifting net · polyester · 20 t klase

Bug-at nga Katungdanan 20 Ton Polyester Cargo Lifting Net

A 20 t working load limit at 7:1: wide duplex polyester bands, eight lifting points and a rating that comes off the test bed, not off a table.

20 t working load limit 140 t minimum breaking load 100 mm duplex band 8 mga punto sa pagbayaw
Heavy duty polyester flat webbing cargo lifting net laid out, wide bands in a square mesh

A heavy duty 20 ton polyester cargo lifting net is a flat lattice of wide high-tenacity polyester bands, stitched into a square mesh with a doubled border and four or eight reinforced lifting points. The load sits inside the mesh and is carried across the full width of every band beneath it, so the pressure on the cargo is spread over a face rather than concentrated on four sling legs.

We build these nets to order in Taizhou: band width and layer, mata sa baling, gidak-on sa net, lifting points and printing are set from the load, and each net is proof tested on our own bed before it leaves with its capacity label and material test report.

The number behind “20 ton”. The working load limit is 20 t and the safety factor is 7:1, so the net’s minimum breaking load is 140 t. That figure is what the test bed proves; ang 20 t is what you are allowed to lift, in the arrangement the net was rated in.

Why polyester at this rating

Sa 20 t the net is under load for a long time and usually lifted many times a week, so stretch matters more than it does on a one-off lift. That is what decides the fibre.

Lamesa 1 — Polyester against nylon for a 20 t net
Polyester (PET) Naylon (PA)
Stretch under a steady load Low — the net stays square and the load stays level Markedly higher; the net settles and the load can tilt
Shock pagsuyup Kasarangan Best in the family; 18–22 % elongation sa break
Pagsuyop sa tubig Ubos kaayo, dries quickly Mahitungod sa 4 %, with some strength loss when saturated
Repetitive crane cycles The usual choice Better where pickups are rough
Temperatura sa pagtrabaho −40 °C ngadto sa +100 °C Lower at the top end
Best fit for a 20 t load Giputos, palletised, bundled or stacked cargo lifted on a cycle Irregular or shocky loads that must settle into the mesh
Nylon rope cargo net for comparison with a flat webbing net
The rope alternative: better on irregular loads, but it stretches far more than a polyester band net under a steady 20 t.

What changes when the rating goes to 20 t

Capacity is not a property of the net’s size. It comes from four things moving together: ang banda, the number of load-bearing bands under the load, the corner points, and the hardware the points gather onto.

Lamesa 2 — Build steps from a light net to a 20 t net
Load band Band and build mesh Mga punto sa pagbayaw What else changes
2 – 5 t 50 mm single layer 100 mm 4 corners Standard warehouse net
5 – 10 t 50 – 75 mm, duplex on the load run 100 mm 4 corners, 8 sa hangyo Heavier border, reinforced loops
10 – 20 t 75 – 100 mm duplex 100 – 150 mm 8 points Master ring or spreader beam; net built to drawing
20 – 30 t 100 mm duplex, band count from the load face 150 mm 8 points Spreader beam in the assembly; proof test per net
Ibabaw 30 t 100 mm multi-layer or wider pitch 150 – 200 mm 8 points or more Engineered and tested to the lift, not to a catalogue

Build steps above 10 t are our standard practice; the rating of any individual net is fixed by its own proof test and quoted from that certificate.

Duha ka sangputanan ang mosunod. Una, the corner loops and the master link or spreader have to be rated for the same 20 t — a net rated 20 t sa a 10 t ring is a 10 t asembliya. Ikaduha, the same net can be rated differently for four points and eight: the label states the arrangement it was tested in, and lifting it another way changes what it may carry.

Corner detail of a heavy duty webbing cargo net, folded double-stitched border and reinforced loop
Detalye sa eskina: the doubled border is spliced into the loop, which is where the whole 20 t passes through — and where a net is inspected first.

Sizing the net to a 20 t load

A lifting net must be bigger than the load, or the cargo sits on the border instead of inside the mesh and the corner loops pull straight up through it.

  • Flat form: allow at least 100–150 mm of net beyond the load on every side, and more where the sides are vertical or the load is loose. A 2.0 × 2.0 m load therefore takes a net of about 2.3 × 2.3 m or larger.
  • Porma sa bag: the flat width has to wrap up the sides and close over the top, busa patag nga gilapdon = footprint + 2 × bag depth. A 1.2 m footprint in a 0.6 m deep bag needs about 2.4 m tabok.
  • Corner legs: the four or eight legs have to reach the hook or master ring without lifting the border off the cargo — a common reason a net that fits the load is still too small for the lift.
Flat polyester cargo lifting net spread on the floor with four corner lifting loops
Flat form: the net overhangs the load footprint and the four corners gather on the hook, so the cargo sits inside the lattice rather than on top of it.

mesh: gidak-on gikan sa kargamento, dili ang tonelada

Mesh decides what cannot escape the net; tonnage decides how strong the bands are. A heavy net with too open a mesh spills small items whatever its rating.

Lamesa 3 — Mesh against the smallest piece in the load
Pinakagamay nga dimensyon sa kargamento Typical cargo at 20 t Mesh aron matino
Ubos 75 mm Mga gagmay nga casting, mga sangkap sa kadaghanan, drummed goods 100 mm diamante, o usa ka sirado nga bag nga pukot
75 – 150 mm Mga tisa, giputos nga mga butang, gipikas nga bato 100 – 150 mm
150 – 250 mm Sawn packs, bundled tube, mga karton, scrap 150 – 200 mm
Tapos na 250 mm Mga bloke, dako nga bato, mga debris sa demolisyon 200 – 300 mm

Espesipikasyon

Lamesa 4 — Heavy duty 20 ton polyester cargo lifting net
Parameter Espesipikasyon
Type Ablihi ang patag nga webbing lattice, upat o walo ka punto sa pagbayaw
Materyal nga banda 100 % high-tenacity nga polyester (PET); nylon or UHMWPE on request
gilapdon sa banda 75 – 100 mm for this class
Band build Duplex (doble nga layer) on the load-bearing run, single layer elsewhere
Pag-abli sa mata 100 – 150 mm; square standard, diamond on request
Pukot nga gidak-on Typically 4.0 × 4.0 m sa 6.0 × 6.0 m, or to the load footprint
Limit sa karga sa pagtrabaho 20,000 kg in the rated arrangement
Kaluwasan nga hinungdan 7:1 - minimum nga breaking load 140,000 kg
Border and corners Doubled border, gidugtong sa mga suok; reinforced loops, four or eight
Mga gamit Master ring or grade 80 mga kadena; spreader beam for eight-point lifts
Pagtambal Na-stabilize ang UV, anti-tigulang, abrasion-resistant finish
Temperatura sa pagtrabaho −40 °C ngadto sa +100 °C
Pagmarka WLL, arrangement, net size and identification on a sewn label; band printing on request
Dokumentasyon Capacity label, materyal nga pagsulay report, Pagmarka sa CE; gisulayan sa atong kaugalingon 1000 t bed
HS code 630790
Polyester webbing cargo net with the border and lifting loops visible across its width
Border and loops: the perimeter takes the load from corner to corner, so no single stitch line carries the lift.

Eight points, dili upat, once the load is long

Twenty tonnes gathered onto four corner loops means each loop carries about 5 t before any angle is taken into account; from eight points it is 2.5 t each, and the load face stays square instead of bowing in the middle. That is why an eight-point net is paired with a spreader beam or a master link rather than hung from a single hook.

  • Four points suit square, compact loads where the net is only holding the cargo together;
  • Eight points suit long or wide loads, and any lift where the net must stay flat under load;
  • The spreader or master link, the slings above it and the hook must each be rated at least 20 t;
  • Never lift from fewer points than the net was rated for, and never knot or shorten a leg to take up slack.

The leg sees more than the share: sa 45 deg from the vertical, a 2.5 t share becomes about 3.5 t along the leg (2.5 / cos 45), which is why the slings above the net are sized from the angle, not from the load divided by eight.

Inspeksyon ug pagretiro

Lamesa 5 — What ends a net’s service life
Susiha Pagretiro o pag-ayo kung
Corner loops and their stitching A loop is deformed, the stitching is broken, or the band is cut at the throat
Border Ang utlanan giputol, flattened, or has pulled out of a corner
Load-bearing bands Any band is cut, nasakitan pag-ayo, heat glazed or chemically stained
Mesh geometry The lattice is distorted from an overload — the net no longer sits square
Pagtahi Stitch lines are broken or pulled at a crossover
Label and printing The WLL or the arrangement is illegible — an unlabelled net cannot be rated

Inspect before each lift and have the net examined by a competent person at the interval your site sets. Tipigi kini nga limpyo ug uga, gikan sa yuta ug gikan sa direkta nga adlaw; never knot, weld or heat-repair a webbing net.

Steel coils loaded inside a webbing cargo net on a factory floor
Coils inside the mesh: at this rating the net is as much a handling tool as a container, and the crane never touches the cargo.

Giunsa kini pagtukod, and how the rating is proven

  • Bands woven, not cut from sheet. The webbing is woven to width and stitched into the lattice at the crossover points, with the stitch pattern set so the thread takes shear rather than peel.
  • Lattice laid square. The mesh is set out from the drawing before stitching, so the bands under the load line up with the load face instead of running diagonally.
  • Border spliced into the corners. The doubled border carries the load from corner to corner, so no single stitch line carries the lift; the loops are formed out of the border.
  • Proof tested, then labelled. Each net is loaded on our own bed and fitted with a label stating the working load limit, the arrangement it was tested in and the net number.

Ang parehas nga mga buhat naghabol sa webbing ug nagpilit sa mga ferrules sa wire rope, which is why a net, a webbing sling ug a lambuyog sa wire rope on the same lift can be matched in rating rather than bought from three suppliers.

Diin a 20 t net does the work

Lamesa 6 — Sectors that buy this class
Sektor Unsa ang gibayaw sa pukot Kasagaran nga pagtukod
Steel ug fabrication Mga bundle, mga seksyon, mga load sa stillage patag nga pukot, 100 mm duplex, eight points
Stone and quarry Mga bloke, gipikas nga bato, mga bato Porma sa bag, 150 mm nga baling, mga patsa sa eskina
Mga pantalan ug mga terminal Bagged and unitised cargo, quay work Flat net on a spreader, giimprinta nga WLL
kahoy Sawn packs, mga poste, sleepers Flat or bag, 150 – 200 mm nga baling
Scrap ug pag-recycle Mixed ug abrasive scrap Dako nga mata sa baling, wear bands at the corners
Precast kongkreto Units, mga singsing, mga panel Flat net with edge sleeves, eight points

Kanunay nga gipangutana

Ang 20 t rating for the net or for the whole assembly?

The net is rated 20 t in the arrangement it was tested in — four or eight points, on the fittings supplied. The assembly as lifted is limited by its weakest part, so the master link, mga kadena, spreader and slings above must be rated at least 20 t as well.

Why is the safety factor 7:1 ug dili 5:1?

7:1 is the factor we build to for this class, which gives a 140 t minimum breaking load for a 20 t rating. Where a site works to 5:1, say so at enquiry and the net is built to that factor instead — the rating on the label always states what it was made to.

Polyester or nylon for a 20 t pagbayaw?

Polyester where the load is lifted on a cycle and must stay level — its lower stretch keeps the net square. Nylon where the pickup is shocky or the cargo is irregular and has to settle into the mesh; it stretches far more, which absorbs the jolt but lets the load tilt.

How big a net do I need for a 2 × 2 m load?

At least 2.3 × 2.3 m to give 150 mm of overhang on every side, plus enough corner leg to reach the hook without pulling the border up over the cargo. Send the footprint and the hook height and the leg length is worked out from those two.

Can it be lifted by a single hook?

Yes on four points, where the four loops gather on a master ring under the hook. On eight points a single hook would pull the net into a cone, so a spreader beam or a two-leg arrangement is used instead.

Can you print our brand and the WLL on the net?

Yes — WLL, arrangement, gidak-on sa net, fleet number and your own brand can be printed along the band, with a sewn label as well. Yards running a fleet of nets usually ask for it.

Pangayo ug quotation

Send the load and how it is presented

The cargo — what it is, giunsa kini pagputos, and the weight as presented for the lift;

The footprint — length × width, plus height if a bag form is needed;

The lift — four or eight points, gitas-on sa hook, and whether a spreader beam is available;

The duty — how many lifts a week, indoors or on a quay, and the temperature range;

The paperwork — CE marking, test report and own-brand printing if you need them.

Send the load and the footprint for a quotation →

Kung asa moadto sunod

Kompanya sa Lift Sling Rigging · Lifute Industrial Park, Dakbayan sa Taizhou, Lalawigan sa Jiangsu, China · HS code 630790
Ang Tel +86 523 8693 5818 · WhatsApp +86 180 6600 2268 · lift98@jslift.com· xulft.com

 

Biyai ang Imong Mensahe

Pag-scroll sa Ibabaw